Video

Can you post a circuit diagram for the same as the same as the video

Is the app are notify when you are in parking area only? How to make the app are notify although you are not in parking?

Why are you using Durian Uno instead of Arduino Uno? If I replace it with Arduino, will the code remain unchanged?

It's not working has been changed the pin number

Salam boleh tk buat circuit ni kat tinkerkad, FYP saya plss

Why Does it said the Durian Blynk 8266 firmware version 1.0.1 Failed

Sir can we use arduino UNO instead of ESP8266

Can i get the code?

best work and really useful.........nice prj chip welded is a classical atmega328 tqfp32? Bootloader preloaded or i can put it directly before code? THX a lot and greetings from ITALY

Do you have the code for that

How do you clean it after use? and what solution do you leave the sensor submerged after use?

Can you tell me which speaker you used for this project? It look like 8Ω, but I can't read the wattage.

thanks for the video man, but what about the temperature ? Temperature is also important if you measure PH

Nice alarm setup. Do you have a kit that has a manual reset for the LED? What I mean is a way that when the door is opened, the LED will stay on but blinking on and off. When the door is opened I want it to stay on until I manually reset it with a hidden push button. Let me know when you get a chance. Thank You!

Sir is it compulsory to add 3 LED Since blynk code it is not working so,that I am asking you.

Thank you so much for providing this video. Have a great day.

How can we use ESP 8266 in this for uploading data on server

The system doesnt seem to detect my laser. Any solutions to this?

i doesn't want the decimal. just the number the correct the coding please please please please please

where do we put the trig?

can i put the pH meter without that upper transparent lid that contains water in an running water??

I only get 2.55v not 2.50v when i turn potentiometer, the input voltage is 5.00v checked via multimeter. Should i set 2.55v to pH level 7.00 or what should i do? Thank you!

Can we control all switches at a time, Can the two motors work at that time,bro please tell me please plzzz plzzz bro

Great video but I do things a bit differently. I don't have to reset the start. I replace the drill, reset the Z hight using my calibrator and then set back to zero/zero/zero (home) and start the next run. Also -- Add a line right after the M03 S???? around line 7. For me, I have this M03 S1000. After this line, add a G00 Z2. This way the CNC will not drag your bit over the PCB. It will rise, move to it's start point and then drop to Z0 and then drop again based on the high you made Z, for me 0.1

Basically, The HX711 is a digital device. we can't read the output of the HX711 using the analog inputs (A0). May i know how you are measuring the strain ??

Thanks a lot

can use this code at mega board?

This would have been better if you talked or used an AI text to talk explanation. If you want, I will do your audio for you either narrating in English or using an AI voice.

will you send circuit schematic and codes

durian doh, mesti tajam

Hello Where can i get details about this unit ..?

It is asking password to pair what is it's password bro

Thank you. AT+THNX :)

What is the technology used??

😅 pls tell me that it is really working are u sure 😔(I only have half a month for school projects)

Link for the code

You know nothing about this. This is sound sensor which activates at the appropriate volume level, this level can be adjusted with potentiometer. It just return High, or Low signal, nothing between.

You wrote that the maxsignal is 1024 but it's 1023 because from 0 to 1023 you have 1024 values + 1023 is on 10 bits and 1024 on 11

is this available?

Any muslim here??😂😂

Is it compatible with nodemcu esp8266?

Is it compatible with nodeMCU esp8266?

Can you tell what are the components in mb12 1-120s

Can u give me that code bro?

What is the maximum volt?

Why is the minimum that my ph sensor is 4.13? from there it doesn't go down anymore :c

how did u short circuit the sensor?

need the namesof the components used

Can i use other display in this project.

what jumper wires did you use?