Video

hi my mini is in lamp mode after changing ignition coil and spark plug the car won't start can you help me? best regards

The front control arm does not come off easy I had to take the knuckle off and turn it upside to whack with a hammer.

By far the best video showing how to do this

So. In ready for this bad boy, same problem in my Audi a6 c5 allroad 2002 2.7 biturbo 😮😊

Yo thanks! GREAT Vid helped out alot with my Jeep. Sadly, my problem with "limp mode" got even worse...probably because of the $50 part I got on line. Next time I'm getting a part from a reliable source.

Hey, bro, great video. It was a piece of cake. Question..How do you stop the vehicle from dying when you get in and put your foot on the brake to put it in gear?

I want to know where to buy that socket wrench you used to tighten the bolts on the rim i love that thing

You didn’t explain how to set the tension on the timing belt tensioner

One of my triple square bolts feels stripped. I turn it and it feels like my bit is skipping. I’m stressed the f out. Whats the best way to go about this.

Tha js for the video. It is rare that a product performs and i stalls as shown. Put mine in the first time in less than 30 min.

Those 2 bolts that hold the Carrier mount on are a MUTHA!! to get loose.

Excellent !

I will definitely be doing this for my b7 nice work!

This is one of the nicest engine bays I've seen

is it only one collor for the air vents for the vw b5.5 2004 ? because i cant tell if there is a black version and a grey one out there

Hi, I think my car has the same problem. Check engine light flashing, low power and no compression. Could it be exhaust valve problems? Thanks

The clip i was supposed to pull out flew off i cant get sensor out

How many prongs does it have?

Hello!! .. I am a fellow tradesman! ... I am an old Millwright from Canada, I am retired now. Thank you for posting this, am reping my van and need ot bead roll fuel line tubing. As you may know modern fuel systems operate at higher pressure now .. Up to 60 PSI ... A simple hose clamp can fall off during use! I copied your tool for to fit in a 10mm (3/8") fuel line tubing. It works fantastic .. thank you so much!! I am certain I would never have thought of this on my own! :)

This guy made a fantastic video👍🏽👍🏽

Всем привет, я на своей машине просто побывал этот радиатор моющим средством. Подсоединил один шланг к насосу.

Hi. I've changed my pads like this thank you. But my pad sensor is showing still on my dash. Do they have a sensor else where as I couldn't find any at all 😢

You also have to make sure if you have to add a secondary intake filter for proper flow. Sounds amazing too

Very good tutorial, had a little bit of issue with the steering joint bolt beeing seized but except from that everything went smooth :)

This video help me a lot . Thanks you very much

Do you have the torque specs for the subframe bolts?

This was perfect! Straight to the point and the detail of including the tool needed and torque spec was very helpful. Thank you!

Thank you! Awesome video, saved me much money, and helped me face down the dreaded pinch bolts successfully. Much appreciated with your great production effort & lighting.

Shit sucks video is good but the column won’t let me turn

Do i need to use a grinder to cut open the eom brackets or i can just use a flat screw driver to force open?

Mostly the audi problems are about taking off half the front which cause more work hours. More important is that the manual transmission its more reliable than the automatic one. These stuffs i saw as problems are correct and easy to prevent some serious dmg to the engine. 2.0TFSI for me personally its the best engine for car person who is now family person. Something more i can add is that you can have the best experience if you drive quattro not fwd. The video its really well explain and bro knows it.

Appreciate the help!

Great video thanks for posting, what is your car ride like since installing the PU bushings? I have some for the wishbones on my car, I've heard that the ride is a bit rougher with PU Bushings being harder than the factory rubber ones?? Thanks again.

I also replaced all 4 speakers on my B5.5. But I bought adapters/spacers on aliexpress, I also bought special speaker wires with socket that allows you to connect OEM speaker plug without any wire splicing. Those threaded rivets on a first look seems like a good idea, I am just afraid that those rivets doesn't allow speaker spacer lay flush with door panel, there is a risk of water ingress into interior if its not sealed properly.

Why do they even produce brushed motors still?

ha this is exactly how my 2014 lever looks. need to replace and now i know. thanks for posting!

how do u remove the intake manifold ?

you save my life, thank you from France! Mickaël

You save my life, thank you, your video is perfect! Mickaël, from France!

hacksaw for the front rubber safer and faster

Did you not have to flush it or pressure tesr it

Thank you for all your videos on B7👍👍👍👏

How many miles between each replacement?

Thank you for the visiuals. I'm about to do the same job. My setup looks pretty identical compared to the front of my 97' V6 Audi A4 FWD 12V. I thought I was gonna have to put it in full service position and disconnect the driver side upper radiator hose, it's going to be a tight squeeze! I also didn't realize I would have to remove the tensioner pulley as well. Looking at all the vehicles with their alternator just sitting at the top of the motor just makes me what to cringe at the job that awaits me. 😂

Good evening, could you provide the measurements of the piece please?

Boa noite, será que poderia colocar as medidas da peça por favor.

Is there another way to jack up car in the front of the a4 so I don't have to use the pinch welds on the sides? So I'm able to put my jack stands easily.

Helped me tackle my clutch job this weekend

Hey I was just wondering if the thread on the axle flange bolt is a reverse thread or a regular thread?

Were can I get the hardware needed for this conversion