Video

What is that black filter in the first hose you took off?

Thank you for the video i got the bootloop to stop. The only thing is the buttons are unresponsive to going back or home screen. Maybe the screen just needs replaced?

Thank you very much. I’ve been browsing through many videos but finally found solution in your video. Even though my treadmill is from Pro-Form but the troubleshooting steps are similar.

Hello. I have a Nordictrack e7.2 elliptical which has a this problem. I mede what you sugest in this video, opened the console and cleaned the terminals of the two flat cables and reinserted them into the slot, which worked once, but the second time I try to use the keys they no longer respond. anyone has some idea why is this happening? Note that i've made this procedure more than one time and it's allways the same, works for one time but the next time i try to use it no longer avilable. I should say that i'm very gratefull to "GITGIFT" Thank you very much.

Our Commercial 2450 treadmill belt sides are under the plastic sides so I cannot reach under to lubricate belt and deck. Do I remove the sides or...?

Ur too vague

Thank you! ❤

I hope this only takes me 4 minutes as well. Ill let you know...

this was amazing and worked thank you

Thanks for the video! Does the backup camera in the review mirror still work?

Os botões de start e stop não funcionam. Alguma idéia pra me ajudar?

Hello, can anyone guide me to mounting my sd card back? somehow I unmounted the sd card and i can't mount it back up to be able to proceed with the ifit download

Thanks for posting this. Helped me determine it was the controller not the motor. Got a new controller on warranty so pretty pumped!

Good video, but the music is REALLY, REALLY annoying.....

I got to the end of the apk install. It tells me "success...please wait while ifit reboots" then freezes.

Our 1750 either slows or stops after a period of time, around 30 minutes or so into a walk or jog. What should I focus on?

Exterior is easy......how do you clean the inside of the belt???

sweet porn music

Good video, no stupid dialogue, just information! BTW a jump pack or jumper cable will power a gate just fine until one gets around to running power. I welded a lifting eye at each end of mine for easy install with an engine hoist. How much you can carry depends on your rear suspension (stock is always soft) so I use Hellwig overload leaves and Timbren urethane springs (they do not conflict) on my F150.

On 2450 Incline works, Speeds stays on #1 setting only. Any thoughts.

Would you be able to make a video explaining the wiring better?

I was curious what the symptoms could be on a motor that has not quite failed but maybe is on its way out. For example on my 2450 recently if you set the speed to 4.0mph it seems the motor speed might fluctuate slightly slower for some time and then speed back up. Not always but sometimes or in one case to get a 4.0mph pace I needed to have it at 4.8mph. But maybe the incorrect voltage is going to the motor to cause this and maybe the speed sensor is the case.

I can’t find the pin hole I have a nordictrack 2450 commercial treadmill and the screen is just blank and the fan turns on

It feels like I’m going to snap my bolts when I go counter clockwise. Any ideas why that might be? I don’t want to push too hard

minen turns on the screen but will shit off in inseconds will shut off any suggestion ? I have removed the electrical cover and I do have 120 volts coming in to the circuit board though thank you in advance

I just bought a used ND 1750 Commercial, 22 model I think. When I turn the Cushion Knob on the side, theres no locking/unlocking or movement of the mechanism. Any idea what might be the issue?

How do you reaccess the android menu before it jumps to iFIT menus?

Looks very useful for my upcoming replacement, was surprised to see that I couldn't find anything official (maybe I shouldn't be). Thanks.

Thank you so much, I will donate for a beer :)

How could remove the coil out of the shaft?

I have a C2155 model...is there a vid out there that shows how to replace the drive belt on that? It's different from the C2150.

What device did you use to pull the flywheel? Is it something you made or purchased? Thanks

Well definitely didn't miss the unneeded dialogue. I will now Subscribe to see what else you can fix!

Nice video but why did you replace the wheel? Was it noisy

Good afternoon! Thank you for this awesome and informative video. We have some house guests that will be filling up our 136 yr old house in June. When they leave, we will order a 1750 or a 2450. I am sure the answer floats around “it depends”, but how often do you do a lubrication on these machines (2 people using it 2 or 3 times per week)?

Intro: RIP Headphone users

Where did you get the servo motor from?

I am trying to go to the website however it says no sd card. Not sure what to do from here?

Has anyone replaced the roller? ones I got do not look like this one has.

Good job 👍

Great video and details. Is there another bearing kit set that may work? The product link in your video is no longer available 😢. Thanks for making this video!

My dad has been trying to solve an issue with his 2450 going full speed (possibly faster than programmed top speed) as soon as he turns it on. Any advice or direction you might have to help diagnose the cause, and what likely needs to be replaced?

Just did this for a ProForm Cycle Trainer 300 CI. Bearings: 6901-2RS Bearing 12x24x6mm, 6001-2RS - 12x28x8mm. Note: don't need to do the steps from 0:05 to 0:12 - the axle stays affixed to that part. Instead, just remove the snap ring on the opposite side (which the video doesn't show), using a snap ring removal tool. Edit: note the smaller bearing slips in too smoothly into place, so it can wobble. I think this is the root cause of why the bearing is going bad on the 300 CI.

Will this work on mine if the start and stop buttons also aren’t working?

My s22i was making a scraping sound, the pedals were a bit loose. After removing the left pedal and shifting the whole drive assembly left, then putting the left pedal back on and tightening it down with some T-Handle allen wrenches it was very smooth and silent

Se ve súper bien tu espalda 😂😂

Thank you.

Bonsoir, j’ai besoin de savoir quel outil vous utilisez pour enlever les deux pales du ventilateur, chez mon brico marché ils n’ont pas l’outil, merci pour votre retour. Cdt stephane

Hell yeah brother

You’re the man, thank you 👊🏻