Video

E a frente? Quanto deixou?

That was a lot of words for not much information. You're not telling us the critical part of the information - if toe gain or loss creates a tighter or looser turning car, and where does it benefit.

Very good and helpful video, thank you!

Servus, ich hab mir das Ladegerät geholt, jetzt geht grad bei uns auf der Strecke das gerücht um, das wegen dem lader das berühmte lipofeuer im fahrerlager war, stimmt das? und gibts irgendwas was ich beachten sollte?

You can buy the same thing from the hardware store for $10

I have been trying to find a lap time comparison using a traxxas tqi vs a higher quality radio and I cant find this comparison anywhere on CZcams

Welches Ladekabel benutzt du im Video genau? Weil der Balancer direkt ins ladegsrät geht ohne Balancer Board.

What is the blue tc body in the beginning of the video?

Which is better? Hardened the front or loosen the rear by one notch on the centric from default settings..

I have a Power HD DW-25LV Servo that I've never used. I was You're going to put it on my Axial Wraith, and never did. So the servo went out on my Brushless Helion Rock Rider. Would it be able to handle 7.4v 2s power? It says low voltage and I don't really know much about servos, so I was needing advice so I don't tear up a never used servo.

Hi Patrick, thanks for showing the power-supply function, to me this is a killer feature. Can you tell us can you use more than one channel at a time on power-supply function, perhaps to run two different items with different power requirements at the same time? I am thinking for powering my FPV goggles and a quad copter for bench testing.. Thanks!

Hello, thanks for sharing. What's your base setup for a loose track, go some ideas for a good starting point? I've got softer springs, thinner anti-roll bars, more droop and chassis flex maximised. I also adjusted the pills for more inboard toe-out and anti-dive (0.5mm down and out). I also put shims inside rear camber links 2mm for roll center adjustment. Any other ideas?

Changing spur is cheaper ..😂 get the pinion which can take the most FDR/gear mesh from the spur..

Toni, my man! Where is that fancy red MST from preview? You show us some other non drift car.

Hello. I hope you succeeded in turning on the recirculation system. If not, then again, to get into it you need to run the charger from the battery, and not from 220 volts

Welches Lenkrad hast du auf deiner Flysky montiert ?

Patrick can you tell us more about the recycle mode. I assume a multi channel charger will allow you to discharge out of a second channel using a discharge bank or however you call it in Europe. Thanks again for the videos, go Team Mugen Seiki! I just became a team driver as well here in California. Hope to hear from you soon.

Very nice charger. At first I thought it was way too big compared to many of the nice compact chargers out now. But after seeing all the charge options and out puts this is a very nice way to go.

Hello. I always look at your reviews. But today I'm a little disappointed. The review is poor. This charger will allow you to discharge with a current of up to 15 amperes; for this there is a recycle mode. It also allows you to charge with current up to 30 amperes. But nevertheless THANK YOU I’m writing through an online translator, maybe it won’t translate correctly. To use the 15 ampere discharge mode, you need to connect a battery as a power source. And when it is used, current flows into it.

Hello I always look at your reviews. But today I'm a little disappointed. The review is very poor. This charger will allow you to discharge with a current of up to 15 amperes; for this there is a recovery mode. It also allows you to charge with current up to 30 amperes. But nevertheless THANK YOU

I literally thought that the thumbnail was a cyber truck. Lol

Auf welcher Plattform kann man die Videovorschläge schicken bzw welchen Kontakt?

Looks like cybertruck.. 😂

Was interessant wäre, wäre ein Video wie man Fahrzeug vorallem auf Teppich High Grip besser oder einfacher rollt. Das gleiche im Kombination mit den Flex Einstellungen was was genau bewirkt.

Manual could use work...lol

I bet when the camera cut off that shock started rebounding

Will this happen to transfer over to Rc Drifting.??

With all the precision tool created for measuring this and that but there is no tool to measure sway bar.. 😂

How often does a carbon sassy have to be replaced?

Good Day Toni, trying to run a 96 spur, however, it's seems other brand spurs don't really fit or am I missing some sims? Can you please help me out and check if your kit can take the older axon or other brand spurs? Appreciate your help - cheers

I don’t know what car to get next. So many choices. Xray, Mugen, Xpress, Axon etc 😂

Better than Mugen? It’s more ex than mugen over here.. 😂

If I get 4 cheap digital scale would it be the same? 😂

Good old days in the 90s building a rc car on the floor..no dropping of screws, shims, orings, clips, ball diff 😂

Pls don’t use the toe gauge too much. It may get tweaked.. 😂

At first when i started watching these videos i thought that this guys name was Toni so he called his channel tonisport. Then i saw tonisport was sponsoring RC drivers and started to wonder. Then i heard he said his name is Patrick 😂😂😂 excellent content though, absolutely love it

My how the times have changed. Fast forward to now and gluing sidewalls is considered mandatory.

Hear me out hear me out......negative front chamber HEHEHEHEHEH *puts joint down*

Is traction the only reason tc's flip?

Wouldn't there be an advantage (in time) to the tweak methods that don't require you to put on special wheels?

Nice.. I just tested on my car..😂

Can use ride height gauge to measure also without the 10mm blocks..😂

What a great video! Thank you so much.

Unfortunately the body stops plastic still scrap off the body paint.. 😂 I put small piece of tape under the body..

bisschen wie der BD11 von Yokomo ;)

Wann kommt den das Fazit bzw. die ersten Streckenerfahrungen mit dem Mugen MTC2R?

So fast TITC again 😂

Does anyone know if you can program SW1 or SW2 to D/R 100% with the push of either button? I sometimes run a low D/R and in some instances need 100% quickly. Also, can you change the trigger throw to 80/20 instead of the 50/50?

Ich kann den Ersa Independent 75 sehr empfehlen. Funktioniert zum einen mit Feuerzeuggas und wird dennoch bis 580°C warm. Meine 8AWG Kabel habe ich letztens auf jeden Fall problemlos angelötet, bei etwas über halber Leistung. Auch der Gastank reicht wirklich lange.

手が足りません(笑)