Video

Man you should send me one of your printers to review and make videos on

Why the bell is etina not an option in wiibuikder????this mess is annoying as hell! It shouldn’t be this dam hard !

The filament leaks above the nozzle what do I do?

I entered card but it says print from TF not SD.

For those who can't get the tube out, even when you press the black rubber ring, I figured out a solution. Follow the instructions for replacing the nozzle (easily found on CZcams). Make sure everything is completely cooled down. When you pull out the silver metal thing that the nozzle screws into, the stuck tube will come with it. Gently pull it through until you have enough length to work with. Use pliers and wiggle the stuck tube back and forth until it pops out. There will be a bit of a crimp but you can even it out with the pliers. I did a dry fit test before I put everything back together by sliding the filament back up the tube the wrong way to make sure it would still fit. We're currently doing a test print and everything seems to be running smoothly. I'm posting this on multiple videos since plenty of other people had the same problem I did and no one had a helpful answer. I hope this is useful.

For those who can't get the tube out, even when you press the black rubber ring, I figured out a solution. Follow the instructions for replacing the nozzle (easily found on CZcams). Make sure everything is completely cooled down. When you pull out the silver metal thing that the nozzle screws into, the stuck tube will come with it. Gently pull it through until you have enough length to work with. Use pliers and wiggle the stuck tube back and forth until it pops out. There will be a bit of a crimp but you can even it out with the pliers. I did a dry fit test before I put everything back together by sliding the filament back up the tube the wrong way to make sure it would still fit. We're currently doing a test print and everything seems to be running smoothly. I'm posting this on multiple videos since plenty of other people had the same problem I did and no one had a helpful answer. I hope this is useful.

Bill gates rap

Did you solve your problem mate ?

Hey I have a problem with the Tina2s it keeps saying y homing failed and I watched your video about how to fix it but I don’t see the same as you guys do

Amazing

I have a weedo tina 2. The nozzle looks the same. Where can i buy a replacement?

the design is very human

Can you 3D print erectile dysfunction medication? Asking for a friend

I’m unable to remove the plastic tube from the nozzle it seems to be stuck please help

Was the cat in the backround a illusion 😅

That arrow one is actually pretty sick

Question what cameras are compatible with your tina 2s printer

whats the coupler size? 5 x 8mm?

The surface area is not observed by the change for your perception to comprehend.

Me biting it

The middle row is shorter, hence the extra chocolate

Just FYI, it's much easier to remove the tube if you heat the nozzle to 200 BEFORE trying to pull it out.

To remove the hose ends push down on the little black rubber ring at the same time you pull the hose. To get to the one attacked to the nozzle you'll need pinch it down with forefinger and thumb so you don't accidentally force the whole mechanism down, while your other hand pulls the hose.

Thanks dude, you saved me from wasting my money

simply push the clog through

With my printer I need to replace the pneumatic coupling

how do i get the 2.4hz internet Connection ...

what if we cant get the tubing out? ours is stuck in it

Who’s smart enough to not tell your age 👇

Tengo esta misma mini impresora para los niños, pero no consigo que haga modelos buenos, las primeras capas son muy toscas y sin detalles y si intento hacerle una figura articulada no tiene movilidad y se acaba rompiendo po la zona de las articulaciones.

Help when i try to do take the tip off it turns the brick thing that is on top of it how could i fix that

Please what is the price of this printer

how do i edit things to have words on it

send a link to the slicer plz

What set screw? I can not see it in any of the videos.

Thanks

it doesn't upload, do you have any tech faq or something?

B A N A N A S

Hi i have the problem my nozzle Temperatur is not going over 180 and then it says nozzle fail please restart the 3d printer i need help!❤

What size spanner to remove the nozzle please. Bought some spanners off eBay and none of them fits.

Mines clogged to the max. Piece of crap printer. What does size socket to remove the damn nozzle ? Bought some printer spanner's off eBay and none of the fits :( better off buying easythreed K7 less hassle

Hi! I can't loose the noozle. When I try, the whole hot end turns with it

Whare do I download it for Mac

link to website for wiibuilder?

I removed the set screw and cut a zip tie. Got the heat block lowered and a clog popped out. Printed something, and now its back to clogged again... Do you have to take the printer apart every time you print something????

not work , pls help me

does anyone know how to reset all settings for slicing ?

That ending... lol 😂

Neither way works for me. ☹️