Video

Thank you for the video. Customer needed a new fob battery and I wasn't quite sure where to try and open so this made it crazy easy.

Anyone run into issues with the steering knuckle not lining up on the top bolt? Seems like the cv is a tad too long. It’s seems like a it’s seeded properly. Please help!!

that's awesome! great for black ink but what about the color ink?

Mine only locks but doesnt unlock

What and where is the relay to replace for the trunk rrlease for my 2014 impala ls

Hello... Other day i had check engine light came on..checked and showed code p06dd .. but I had another thing happened which I noticed is that normally on highway going 100 km /hr my rpm were around 1600 and after the engine light and code they are sitting around 2200 ...can that oil pressure make the rpm affected by it.. ?? Any suggestions will be appreciated

How do you check it?

Haha perfect! Very helpful thank u!

I found that the 25 amp fuse next to the 30 is for the drivers side Automatic window. The right hand side fuse only works for the passenger right.

Got a rental, sitting at a gas station and could not figure it out. Thank you for the straight to the point video, helped out a lot.

Amazing explanation the only one thing what you forgot is to decrease the rotors of the oily hands

So far, the only video where they do it correctly.

Thanks! I was nearly certain that was the procedure, but when it suddenly put up a lot of resistance to the last bit of rotation, long time UV exposed plastic, and me being involved, I was afraid i was about to snap the arm!

How do you access the heating element lol

Thanks for showing how this is done. It just saved me $55 dollars in labor from a local shop.

exactly what i was looking for perfect video no bs straight to the piont

I stood at my car for 15 mins, unlocked it like you said and wahlahh👌🏿👌🏿

My garage door light isn’t blinking

Please note that, if you have a key fob that is "quirky" or doesn't seem to be working right, you may not have to "program" a new one. It is very possible that the "electronics" are ok and the problem is deterioration of the "physical" components (the most frequent problem is that the little disks under the rubber "buttons" [used to activate each feature] become detached and float around inside the key fob). If you have trouble "activating" a new key fob, try just swapping the circuit board from the old key fob into the new key fob case [remove the existing, old, "cut" "emergency" key by sliding the release button and pulling the key out, then use a thin knife or shim to force the front of the old key fob case to separate it from the back]. Remove the new "uncut" emergency key from the new key fob and open the case as above. Swap the old "already programmed" circuit board into the new case. Snap the front and back pieces of the new case together and insert the old "cut" emergency key to the new case. If the "old" electronics are ok, the new case/old electronics should work just fine.

What are all these extra parts I have left over? D:

I only have one key. Just like in the video, it will start my Jeep and lock it but not unlock it. So am I to assume that this system will not work for me to program a new key?

Thanks. Its obvous for some but I didn't know that before

Dude you got the wires mixed up.

OMG exactly the same problem on my Venture - this worked, it now seems to acquire satellites quicker than it ever did!!! Thank you so much

Oh, you can only see the battery compartment? Was hoping to replace the rubber pieces because mine are gone. I got a new fob online but it still has to be cut and programmed.

Thanks for the inspiration bro I installed one after watching this video in my old 2013 Chevy Impala LT. It was easy as cake the engine's power was restored immediately it drives great!

Thank you! Perfect explanation.

Where is the ac relay?

Big help for us Simpletons lolll 😂. Thanks!

Thank you. This was very helpful. You were also correct about the driver side having a lot less room.

What was the socket size for the pully nut?

How do I contact you if I want to do business with you? Can you leave me an e-mail?

Also, which relay switch is for the hazard lights on the Chevy traverse cause I can’t find mine

How do you fix the seat? My passenger seat is stuck in recline. I have a Chevy traverse

How do I check the alternator fuse on a 2011 Chevy treverse

Did you install it with or without your battery still connected?

This was a joke no help at all

this is an excellent video. I have 2011 dodge caravan. oil pressure switch out. i tried last night to do it. failed. couldnt get unplugged. but you did wonderful job with video. i will try again

I may be wrong, but I believe you repaired the recirculation door actuator, not the blend door actuator.

Thank-you, was promised a like for like vehicle and ended up with this one. Could not open the darn boot, couldn't find the lever for the fuel, tried looking for the gps... so much confusion. Rental companies just hand the keys and think everyone knows every type of vehicle. Videos like yours help out big time!

Does it care about if its in park or drive? On or off? Doesnt work for me but sometimes it does...

So the "feeder" batteries were connected positive to negative, etc., for all three batteries? Then the positive and negative wires from the three were applied to the appropriate terminals in the dead battery? I have four good batteries. Thanks. Just need verification and then give it a try. Thanks.

Thank you! Rental and no info!

Just now changed out my fuse. You were a great help. Thank you so much!

One of the wire terminals burned off mine (someone didn't turn off the breaker after i told them to!) I have a 16 gauge terminal, but it looks like the light wire actually has a 22 gauge. The terminal fits but the wire doesn't look as snug. Also the terminals look like a different color, not sure if the old terminal color due to oxidation. Does the new terminal have to be a special type, or are any terminals okay?

In the under hood fuse box which fuse is to the air conditioner compresser ?

Great video big thanks

Thank you. Just what I needed when I needed it

I just replaced my bad struts and had to cut off the sway bar links to remove it. My dad helped me on one side and he caught part of the boot with the grinder. But we didn't know. The next day I removed and replaced the passenger side all by myself. But doing a second check on the abs but I noticed the boot was leaking grease. Thank you for the very easy to follow video and not talking forever in the introduction.

we want to invite you to review the latest taillght for 00-06 chevy Tahoe suburban, how to contact you?