Video

what were the symptoms that you had that made you know you needed to replace the drivers side axle?

Hello, does this address P0765 error code? 🤙🙏

How about P0935? I found 6 experts but still cannot fix the issue.

Thank You !

What would be the issue if the air mostly only blows from the foot well and barely from the face vents, and you fix the issue sometimes id have to turn off and on the car

You made this an easy repair. You answered my only realy question was how to remove the access panel. Thank you!

Can’t believe these things use drums vs disc in the back in 2008.

Did you remove the front driveshaft first? This seems required to access the refill plug. Maybe with an E55 torq socket?

same thing happened to me yesterday. then smoke started coming from out of the switch. i gotta get it fixed

Do you now Witit how many miles is recommended to change the timing chain?

Hello how many milles it has when the Bering problem?

Where can I phase those assembly

Were you able to change the bushings with the rear wheels on the ground?

Love the recap

Excellent video and very helpful. Prior to changing the clutch pump I took the cover off the opposite side and replaced the gasket and filter then put new oil in.💰💰💰. Hoping it was perhaps low on oil but the Service Rear Axle light still came on. I purchased a new one and proceeded to change the pump and top off the oil. I was able to take the 2 pins out of the new connector and use the original pins from the difficult to get at harness. (I made a little pin tool and it worked slick as heck) Thanks for the heads up. It appears to be working and the light hasn’t came on yet . 🤞

Phenomenal video. Great details and the up close video, especially the pulleys from underneath, helped so much!! Thank you!!!🙏

How did you adjust the beams height??????

Very informative Thank you !

What did u do to not get hyper flash

Hello does anyone has this problem.. I have engine light came on and when I am going on highway the rpm are higher than normal.. Eg. Say on 100 km /hr usually rpm are around 1600.. since this code came my rpm on 100 km /hr are sitting around 2200 ... Any help will be appreciated is that symptom of bad oil pressure sensor

I have an MKX 2011. I’m doing the timing chains after that I have to do the same job you did so now I have a good idea how to do that. How much did it cost you?

So i messed up and turned off the car then pulled out the check plug i lost about a cup of fluid before realizing i messed up. Correct me if im wrong but it poured out more because it wasnt running? Or was it just too full?

Interesting. I had no idea the FX35 had a pump for the rear window. I guess I should change that out since the rear has never worked since owning my 2004 FX35. Thanks!

I managed to do it myself, Rouge 2015 S. Report for the records; - The cap for the oil reservoir is hell to take out, I cut it off with oscillating machine!!! you think it is rough start!! - I don't have the dip stick, so i used a long zip tie ~25'', and i took the mark of the original oil. I fed the zip tie too much at the beginning, it caught into something inside!! with some patience and force i released it, I panicked for 2 minutes, hopefully it didn't damaged something inside. - Removed 12 clips for the black fabric - I left the drain plug attached as i found it rusty, and i don't have crush washer. so i preferred to leave it sealed as is. - I unscrewed 19 screws. Some of them were very rusty. Took the pan down with some splashes. - Changed the screen filter. - Removed the gasket, it was very attached to the metal. it left some unremovable parts on the metal. I tried to scrap it but didn't want to create solid powder inside. - Failed to unscrew the cooling filter cover. 2 screws are very hard to reach or to access. Even i have accessories for the socket wrench. It needs very low profile 10mm socket. So i decide to skip this filter. - cleaned the pan, put new gasket. - screwed back 19 screws - Added the oil, it took 4 liters. You need a long thin funnel. - It took around 5 hours (it could take 3 without my shenanigans)

Example of neglecting your car. LOOK AT FILTHY ENGINE

You didn't do the fun step. When unbolting the belt tensioner, the bolt snaps and there is not enough clearance to extract the bolt stuck in the block. Then it costs a fortune to pull the engine to extract the bolt.

quero en portugues

What a load of old tosh he didn't even show us😂

How many Litres did you end up using?

This is a great diy video.

You have a new subscriber. I’ll start on mine next weekend. Thank you!

i have 2010 altima that even when the recirculating ac is on you can still smell and feel air from the outside coming in

Thank you so micy for the video, I replaced sensors in my 2009 Santa Fe. Earlier my fuel level would always show empty but now it shows 2/3 full. Even though the tank is full and I replaced the sensors, it is not showing correctly. Any idea what else could be wrong?

Is this the bank one cam shaft sensor?

I need the part for a 2016 altima, It cant find one on Amazon please help

There is a missing part in this video. From trying to take out the battery tray to taking out the sensor.

pointed straight to the issue I was having

did you have extremely poor gas mileage as well? My friend has been driving their car for TWO YEARS filling up their tank every few days only driving dozens of miles... :/ Only code was for downstream O2 sensor. p0139 code

Did you use the fixed clutch compressor in place of the variable clutch compressor? If so, how did you rewire it to make it work?

Does the car needs to be started when you do this procedure?

Does it have to be lifted can it just be leveled? Also can a siphon pump be used if you don’t have a compressor?

I do tech support for Cummins Power Gen; I really appriciate a video that is to the point and doesn't try to tell you their life story, well done!

Hey i have an 2003 altima and the air is cold when parked and blows hot while driving, any ideas?

How did u identify which one of those sensors was the one not working

Any idea if this is close to the same on a 2017 QX60? Thks for the info

Does the front windshield have a weatherstrip at the bottom of it before attaching the windshield cowl? I have the 2008 Dodge Avenger R/T 3.5L

I did this, is there a torque spec!! I have to tighten to? I got the sound back after 50 miles. Actually I have not tightened untill the bushing hit the rear flange. I saw in a video to leave some leeway, so there would be some movement in the exhaust pipe !!

Can you come do my car it's doing exactly the same thing

I have the same error code, same vehicle, however it is summer. Im in Florida.

while it’s not the easiest, it’s also possible to do this without removing the wheel