Video

That's correct, but it can be mitigated. Think a round clamp around the rocket launcher instead of hole for the crossbar. The are electrical clamps big enough. I don't use it for anything now, the two rod holders on the crossbar are all I need but they could be adapted for gopro, or anything else creative

@@AndiDan Appreicate the quick answer.

@@AndiDan FYI i asked an electrician friend and he recommended a 1.5" conduit pipe hanger. It would allow you to reverse the way you have the cross bar mounted essentially. You would put the large end of the clamp around the Rocket launcher and then use the smaller in of the clamp to bold to your 1" PVC crossbar.

@@AndiDan How is the stability of the rig when you have it loaded with Rods or other gear? My concern is that it may flex in and out a lot?

@@Mdowling5656 Great idea!

It certainly would, and with better results than the drill. This was more of a fun project for me, rather than a very clear goal of usability. Since posting the video I have given up on the drill mostly because steering is difficult. An 18lb thrust trolling motor would be more than enough power (like the Watersnake T18, which is only 6lb ). Small and light, with a short shaft, it would be much better than the drill idea. It could be combined with a 30Ah LiFepo4 very light battery (about 7lb), which would be placed on the back of the seat, like the one in the video. The only con I see is making sure the prop doesn't hit your feet/legs. I only use leg power in rivers now, and for lakes I bought a Zodiac inflatable, but if I were to do it again I would certainly look at a small trolling motor.

Cred ca singurul care stie e Florin Sasarman... Cred ca filmarea asta am primit-o de la el

Absolute monster. I think I'll finally feel safe to go far from shore :)

I replaced it with some paracord from Walmart. I don't remember the size, but I got like 50 ft. Maybe 1/4 in? It was enough for a 3 lb grapple anchor

I am quite sure it is not if you want a new one. Only option is junk yards or ebay

Deflated for sure. Marked the spot with a pencil when inflated, then deflated it. Even if the glue is on the skin of the tubes, some might reach the bladders, and HH^^ can melt an inflated bladder.

Thanks for the advise

@@fanofallrods2042No problem, good luck!

Salut, asta e singura inregistrare de studio, dar pot sa ma uit pe niste hard drive-uri sa vad daca mai este vreo varianta

Glad it helped!

Pull sideways. See at 3:45

Or if you are talking about the white cover, see 4:28

Yes I just need to lift the white cover enough to put in my LED bulbs

Are the clips hard to put back in and are they necessary?

Just used it yesterday again :) No problems at all. Pads and mounts are solidly on. I only need to have a small rechargeable pump with me because within 15 min of cold mountain water, the bladders contract by a third. First time it happened I though I had a leak, but fortunately I didn't. I top them off and I'm good for the rest of the day. It's also unbelievable how much abuse the bottom of the tube can take on rocks without even getting scratched. Quite impressive.

www.amazon.com/dp/B005LL3ZXW?ref=nb_sb_ss_w_as-reorder-t1_k0_1_4&amp=&crid=2N0JSQL11F6NR&amp=&sprefix=hh66

HH66

If you are talking about the propeller, that electric clamp holds it tight

The rod holders. Since they are mounted on the sides, not only top heavy, but hook up a big fish... Seems like it would rotate away from the tube. I'd be afraid the stress on the tube over time will cause a catastrophic failure.

Also, did you use HH-66 glue? Would it be possible to put the mounts on the top of the tube? I am interested in getting a Cumberland so doing options research. I currently have a Togiak but the tube cover is fabric, not PVC. Same with my Creek Company Sport pontoon.

@@2011KGM I see what you mean. Didn't have a problem at all. When you sit in the boat they actually lean inwards and compensate. I caught 2-3 lb fish and no problem. I doubt they'll fail. The tube will be pulled before the holder will fail. If you are concerned about rotating, put an eyelet on the top or middle of the rod holder, and anchor it to the tab behind the pocket. That will completely secure it Yes, I used HH-66. Yes about the top of the tube. The mount that I linked it both for side and top installation. My cover is also fabric and didn't rip or anything.

@@AndiDan awesome! Thanks!

You can see a detail at 1:06. I drilled a side hole in both scotty holders (check the outside diameter of the PVC to choose the size of the hole), inserted the pvc pipe on both sides, then used a bolt and nut through both of them to hold them together

@@AndiDan thanks for the fast reply. I'm really looking forward to fishing in mine.

@@jimmywallhanger8402 No problem, good luck!

@@AndiDan How long is the pipe between the rocketlaunchers? Thanks

@@jimmywallhanger8402 If you count 1.5 in on each side that goes into the rocket launcher, 30 in. But to make sure it fits, first I glued on the pads, installed the rocket launchers, then measured the distance between them to fit the pvc pipe

thanks! yep, Scotty

All covers are snap in. What specific part are you asking about?

@@AndiDan the one that covers the shifter screws mine is loose and won't stay up. Does it need a little tape glue? Shaped like a tube the first one you remove

@@SodaGumX Yes, I remember that I had to play with it. if you look at it, it's not perfectly round, it's a little oval. Try to slide it on in different positions before installing the knob. It will eventually work

You're very welcome! That's the reason I made the video - I couldn't find it anywhere else. I don't think there's a problem leaving the clips out. There's nothing structural there. I imagine the worst case scenario would be some rattling

@@AndiDan thank you!

Hm... Haven't tried it, I can't help you on that. Try asking www.taurusclub.com/

Glad to be of help, just like others were to me :)

Good to hear from you :)

It is actually Fix Or Repair Daily and in Spanish Fabricado Ordinario Repararlo Diario

I am glad it was helpful :)

Multumim de efort, şi ne bucurăm că-ţi place piesa :) Doua mici corectii: "orb cerşetor" şi "unor paşi inegali".

@@AndiDan mulțumesc pentru corecții :)

Only from another car. Visit some junk yards, and eventually you'll find a merc or taurus that has one intact. Because they break so easily I decided to wrap it in vinyl in the video.

Maybe you find more phones in there :)

Haha! I found a lot of unusual things in there too and now some additional retainer clips that I dropped in and fell under the consule. They're staying there bc I am not removing the entire console.

:)

Thanks :)

@@AndiDan Do you know who I am?

@@jtg9850 I do now :)

Yes, I do, thanks :) I wrote the song when my favorite uncle passed away

Cine stie, poate o sa reusim... :)

Multumim! Cu drag :)

@@AndiDan ... al 100-lea like :) ... Drag Andrei, oare nu va reuniti macar inca odata ... ca sa editati un album? Ar fi fantastic, astfel de piese sint nemuritoare ... va ascult deseori in masina, e un stick special creat pentru drum lung ...

@@cercetasiisibieni9404 Multumim mult :) Ne bucuram ca suntem inca prezenti printre oameni, dar poate ca e mai bine sa pastram ironia numelui pana la capat si sa ramanem cu ce avem pe CZcams :) In principiu, poate, dar Nu Acum :)

@@AndiDan e ok, mai tirziu un pic, dar musai in viata asta, da?!? iti multumesc, ginduri bune de acasa!