Video

right on brother keep the hay a cut'n

I have a baler just like this but my bales are loose how do I get my bales tighter because I can’t even spear them with the loader.

Thanks for the video!

Would you say or do you have experience doing balage with this baler?

It's 50 on the crank,38 on the PTO . She has a lot of life left.

Nice

Your videos are amazing! If you like farming or harvesting videos, I look forward to having you visit my channel to have relaxing moments together!

Sir Need wheel hay rake 2+2 A shape. which work in sugarcane farm. Row system harvesting.

I have 2 454s ,second tractor I bought for parts, i don't know that much about remote operation, cats like the seats on mine also.

Good video. Thank you.

Heh! A Tonutti in John Deere colors! My JD 702 has Deere decals all over it.

How did you release the tension on the baler?? My bales on my 330 are kinda loose. I was wondering how to get my bales tighter.??

Good day from Ontario When we farm we had 574 & MF 255 & yes hours on 574 hrs. were faster. MF hrs. were alot slower. We borrowed a Belarus & that is the one u want to get when renting, very slow hr count. Thanks

Hello. Does that model have the safe cut shearable hub under the turtle?

Epic images

They’re all welded. For good reason. farmers got tired of adjusting it.

Well lads I'm just after getting a international 684 1980 there and she keeps spitting the engin oil out the over flow pipe. I think the man before me lost the original dipstick and put in a shorter one. Anyone no the length off the original dipstick or how much oil I should be putting into it ? Thanks lads

great walk around thanks for sharing!

great video new sub

The spinners (turtles) can be swapped around such that they turn in the opposite direction, including the two end spinners (towers), you just have to swap the top hats. Since there are 7, one will have no one to swap with. You can build it up or at the most only need to buy one new spinner and basically be running all new leading edges. The washers under the bolts that hold the spinners on are conical so attention is needed when reassembling and possibly will need replacing if they have lost their spring.

That chain is suppose to connect to the pin that holds the top link to the tractor. It is there to carry the weight of the mower instead of letting it be supported on the three point hitch.

i just got a 1979 international 684. i am just wondering if you can make how to videos on the fluid changes?

Are you in Louisiana? We have the same tractor without a cab.

Good deal on the rake!! Thanks for the video!

If you are good with a welder, you can use worn knives to build up the wear surfaces.. just make sure everything is done evenly for balance.. check Shoupe for knives and knife bolt and nuts.. we've had good luck with their stuff. Good to see you making some videos again. Good videos! Keep them coming!!

We had a 430.. had to have been a '70 something.. maybe an '80??? Had a couple guys doing custom baling make haylage for us for a few years. They bought it new, then we bought it from them with a couple years of payments left.. must have been '82 when they bought it.. it never ran in the ash from Mt. St. Helens. Nice machine! Wash, don't wash.. we didn't use to wash balers or combines, we have for the last 30+ years though.. makes it much nicer to find issues and doesn't mess anything up, just grease and run it when you are done.. Thanks for the video!!!

I’ve got a 444 and it’s around the same power but it’s slightly older than this with a different transmission, no power steering and it’s a four cylinder, it always starts well

Ok, been chatting on another channel... Checked out yours.. nice video!!! But you need to say something... I talk, I just hide from the camera 😎 except for an occasional glimpse 🤣🤣😎 I'm subbed up, now you need to get more videos 😎

One of the best tractors ever made.