![Daye Danny](/img/default-banner.jpg)
- 5
- 38 782
Daye Danny
Registrace 13. 10. 2011
2008 toyota yaris fuel issue problem solved
2008 toyota yaris fuel issue problem solved
zhlédnutí: 6 941
Video
954rr cbr signal flashing fix
zhlédnutí 2,3KPřed 5 lety
How to fix your led's to flash at a normal speed rate
2015 ford edge low batt hard steering
zhlédnutí 2,7KPřed 5 lety
hard steering issue and battery replacement
I know that for Toyota Yaris 44.1 to 49.7 psi with the engine idling is normal, but my question is what if the pressure is 42 at idle, is that considered low?
Thnx 😊😊
Same problem replaced fuel pump tested old one out nothing wrong with it was just about to do injectors and fuel rail will try this 1st thank you will it be same on 1.8vvti sr/rs model?
Where did you get the remover
Great information
Do you know where the output speed sensor for transmission is located?
And after you’re done, just go back over it with some soap and water good to go baby
TLDR he replaced the fuel relay.
Thanx man
Hi I have the same problem car turns over but will not start car was ok last time I used it
Great job on the information. Very helpful 😊
Thanks. Will be trying this out.
Thank you for the heads up. No issues yet but know I know. Thinking of replacing fuel filter. I have 240k miles same 08.
I have 08 with 248000 Just started stumbling Former mechanic recommended pump and filter replacement. 1 yr ago. Hopefully this is the fix. But I'm keeping in mind Danny's information too. I really like my 08 Yaris, bought it new in 07. It's been a great dependable car
hey danny 10 months my toyota cant start !!!! i change many piece , and ur piece of relay is interisting to see. thanx you a lot man !!!!! i willl checkit !!!!!
Thank you.
Hi, what was your battery reading at iddle and when started with the alternator kicking it. Thanks
Thanks!
If mine is having the same problem thank you so much for this video
This did not work on my 2012 Kawasaki LX. Spent $45 at Lowes for the Klene Strip Adhesive Remover - VERY Disappointed! Had to buy Gallon of Goof Off for $25 to finish the Jet Ski.
Was da leds draining ur bike before u installed resistors??
Life Saver. Ford dealer wanted to keep my 2017 Ford Edge for up to 4 days even when I let them know the warning I was getting was "power steering assist fault". They should have been able to tell me I needed a new battery on the spot. A quick visit to AutoZone, new battery, my car was back to normal. Thank you!!!!!!!
That's cool but you understand adhesive is another word for glue right?
Thanks for the video. I'm buying an older waverunner this weekend and it needs new mats good to know it's as easy to do as I thought it would be
Brother did you have to use one resistor for each turn signal?
Thanks a lot for sharing this info I need to change my mats now I know how . Appreciate it.🙏🏾
Thank you! Very helpful!
Wow after killing myself using goo gone it’s now that I’m watching this video. Fml
Thank you Iv been putting of doing it as I know it would take forever! And now Iv just ordered some 👌
This applies only to the electric, steering models, right?
My battery is new like a couple of months old only and facing the same steering stiffness issue
Hey from what I learned the power steering is electronic
shit that's quick
I laughed at how he kept pushing the camera man/ or wife arm up..... LMAO
This is incredible. Thank you
You just saved me! 07 Ford Edge same issue had been sitting for a year
Did u ever find out
Just did this on two Yamaha ski worked perfectly. Ty for sharing
Where u buy it?
cant find this stuff?
Great video!! I really appreciate you posting this. Too add a little suggestion you could use a plastic puddy knife just for added protection and will do the same job
Use plastic scraper....brake cleaner aerosol cans work as well....great vid
Do you have a video putting new mats on?
I'm about to do this. Thanks for the vid!
Thanks for video, I’m fixing have to do ours.
Will acetone work
Man... just seen this. Thanks 🙏🏻
What brand of the remover are you using ?
Can it mess up the paint?
Great video. However, I am currently in the process of trying it right now… Seems like you only let your adhesive remover sit for about two minutes before scraping it up like nothing. I waited the same amount of time and it ain’t working. LOL I then looked at the bottle and it said to wait 1 to 3 hours. How is it that the bottle says to wait 1 to 3 hours but you only had to wait a couple minutes and it worked fine? (I’m using exact same product as you)
Update… I believe I have figured out why my job took longer than the one in this video… My pads were OEM from 2011, so they were over nine years old. The adhesive had formed almost an epoxy material. Rock hard. So i needed about 10 min of set time, and then the assistance of a 4” razor paint scraper instead of putty knife
Im in the same boat 😆
Thanks dude, great video
Good stuff, thank you.
Thanks for the video. I can't wait for the spring to try this out and put new mats on my ski.