- 152
- 430 124
I Make Watches
Switzerland
Registrace 21. 04. 2022
Hi! My name is Dayton. I make videos about watchmaking in Switzerland.🇨🇭
International Museum of Horology (MIH) in La Chaux-de-Fonds, Switzerland
Today I'm at the International Museum of Horology (MIH) in La Chaux-de-Fonds. I attended the watch fair here last fall but this is the first time that I actually toured the museum. As a collector it's great to have the opportunity to examine thousands of vintage watches. It's also nice to see what the museum has collected in order to gain a better understanding of historical importance as opposed to hype and marketing.
See the chapter index below to skip to the parts that interest you. If you're a watchmaker or an aspiring watchmaker you won't want to miss their restoration workshop starting at 19:24.
Musée international d'horlogerie
Rue des Musées 29, 2300 La Chaux-de-Fonds, Switzerland
chapters:
00:00 intro
00:22 Meridian telescope built in 1913 by SGIP in Geneva. This was not only used to set the time of earthly clocks, but also to time the transit of celestial bodies across the meridian circle to determine and record their positions and distance.
01:24 modern geospatial timekeeping devices from GPS to the iPhone
01:39 traveling down the ramp to the displays on the second floor
02:05 second floor display close-ups - pocket watches and movements
04:15 mechanical contraption made to study / demonstrate the isochronism of the balance with balance spring
04:29 skeleton watches
04:50 automatic watch movements including the tiny Ligne 6''' (13.5mm diameter) A. Schild AS 1775
05:40 second floor display area with bench viewing cabinets - this is fantastic as you can actually sit down and look directly at the watches and movements at very close distance
06:27 quarter repeater pocket watches and wrist watches including a very small Blancpain (Le Brassus) hour, quarter, and minute repeater gold wristwatch
08:22 stages of assembly of the Swatch and a boxed 99,999,998th commemorative (100 million Swatches sold) signed by Nicolas Hayek April 7, 1992. The watch museum in Le Locle has number 99,999,996!
08:52 more Swatches on the ramp down to the first floor
09:44 Swatch "Metrica" GK 263 incorporating a working tape measure into its band. This is one of my favorite Swatches because it incorporates text "New Time Measurements" and the metric scale numbers, is yellow, and graphically screams "tool watch" quite literally (and I love tool watches).
10:03 Ingersoll Mickey Mouse watch and two Lip watches from nearby France.
10:14 Kif, Incabloc, Monorex, Trishock and Seitz Ruby-Shock shock setting oversized models
10:36 Paul Ditisheim pocket watch with an oversized model of a balance wheel incorporating a J. Depolleir & Son New York shock absorber.
10:44 Rolex early waterproof and submariner watches and Rolex waterproof testing chamber
11:03 Abraham-Louis Breguet pocket watches with open movements
13:55 pocket watches with complications - James Nardin (cousin of Ulysse Nardin) circa 1880 lever chronometer watch with perpetual calendar, moon phase and retrograde date indicator
14:19 Charles-Henry Audemars circa 1880 keyless astronomical minute-repeating watch with perpetual calendar, age and phases of the moon.
14:34 Courvosier & Compagne circa 1830 with solar advance retarde, month and date
14:42 Thought to be made by Carl Wagner, circa 1820, a student of Philipp Matthäus Hahn (1739-1790) with hours and minutes, day or night, day of the week, seconds, phases and age of the moon, date from 1-31, and the name of the month and the number of days it has.
15:05 Ulysse Nardin wrist watches
15:59 The Turler astronomical clock
19:06 painting of a gentleman proudly gesturing to draw attention to his large clock with a tiny working model of the earth, sun and moon atop it
19:24 the workshop where the museum does its own repairs and restorations
22:58 narrated walk through the first floor - discussion of my technique and future plans
23:36 the entrance hall
24:03 a Qlocktwo wall clock in French from Schwäbisch Gmünd, Germany
24:12 the event space (where the watch fair takes place each fall)
24:20 the gift shop
24:58 the book shop
25:43 the entrance
26:08 the view of La Chaux-de-Fonds from la Tour Espacité (The Espacité Tower)
#switzerland #watchmaking
See the chapter index below to skip to the parts that interest you. If you're a watchmaker or an aspiring watchmaker you won't want to miss their restoration workshop starting at 19:24.
Musée international d'horlogerie
Rue des Musées 29, 2300 La Chaux-de-Fonds, Switzerland
chapters:
00:00 intro
00:22 Meridian telescope built in 1913 by SGIP in Geneva. This was not only used to set the time of earthly clocks, but also to time the transit of celestial bodies across the meridian circle to determine and record their positions and distance.
01:24 modern geospatial timekeeping devices from GPS to the iPhone
01:39 traveling down the ramp to the displays on the second floor
02:05 second floor display close-ups - pocket watches and movements
04:15 mechanical contraption made to study / demonstrate the isochronism of the balance with balance spring
04:29 skeleton watches
04:50 automatic watch movements including the tiny Ligne 6''' (13.5mm diameter) A. Schild AS 1775
05:40 second floor display area with bench viewing cabinets - this is fantastic as you can actually sit down and look directly at the watches and movements at very close distance
06:27 quarter repeater pocket watches and wrist watches including a very small Blancpain (Le Brassus) hour, quarter, and minute repeater gold wristwatch
08:22 stages of assembly of the Swatch and a boxed 99,999,998th commemorative (100 million Swatches sold) signed by Nicolas Hayek April 7, 1992. The watch museum in Le Locle has number 99,999,996!
08:52 more Swatches on the ramp down to the first floor
09:44 Swatch "Metrica" GK 263 incorporating a working tape measure into its band. This is one of my favorite Swatches because it incorporates text "New Time Measurements" and the metric scale numbers, is yellow, and graphically screams "tool watch" quite literally (and I love tool watches).
10:03 Ingersoll Mickey Mouse watch and two Lip watches from nearby France.
10:14 Kif, Incabloc, Monorex, Trishock and Seitz Ruby-Shock shock setting oversized models
10:36 Paul Ditisheim pocket watch with an oversized model of a balance wheel incorporating a J. Depolleir & Son New York shock absorber.
10:44 Rolex early waterproof and submariner watches and Rolex waterproof testing chamber
11:03 Abraham-Louis Breguet pocket watches with open movements
13:55 pocket watches with complications - James Nardin (cousin of Ulysse Nardin) circa 1880 lever chronometer watch with perpetual calendar, moon phase and retrograde date indicator
14:19 Charles-Henry Audemars circa 1880 keyless astronomical minute-repeating watch with perpetual calendar, age and phases of the moon.
14:34 Courvosier & Compagne circa 1830 with solar advance retarde, month and date
14:42 Thought to be made by Carl Wagner, circa 1820, a student of Philipp Matthäus Hahn (1739-1790) with hours and minutes, day or night, day of the week, seconds, phases and age of the moon, date from 1-31, and the name of the month and the number of days it has.
15:05 Ulysse Nardin wrist watches
15:59 The Turler astronomical clock
19:06 painting of a gentleman proudly gesturing to draw attention to his large clock with a tiny working model of the earth, sun and moon atop it
19:24 the workshop where the museum does its own repairs and restorations
22:58 narrated walk through the first floor - discussion of my technique and future plans
23:36 the entrance hall
24:03 a Qlocktwo wall clock in French from Schwäbisch Gmünd, Germany
24:12 the event space (where the watch fair takes place each fall)
24:20 the gift shop
24:58 the book shop
25:43 the entrance
26:08 the view of La Chaux-de-Fonds from la Tour Espacité (The Espacité Tower)
#switzerland #watchmaking
zhlédnutí: 749
Video
Microqubic Motion Control Video Microscope
zhlédnutí 548Před měsícem
At EPHJ this past week I met Yuksel Temiz, the creator of Microqubic 3D video microscopes. EPHJ is an annual trade fair for high precision, watchmaking and jewelry subcontracting, microtechnology and medical technology in Geneva, Switzerland. ephj.ch/en/ Microqubic AG, founded in Zug (Switzerland) in 2022, designs and manufactures patent-pending modular electro-optical systems and 2D/3D digital...
Eternal Calendar Mechanism Explained in Five Minutes
zhlédnutí 740Před 3 měsíci
In this video Roy Syvertsen from IWC Schaffhausen explains the Eternal Calendar mechanism in the IWC Portugieser wristwatch. Thank you to Roy for letting me publish this incredibly succinct explanation! I note that his explanation includes an explanation of how regular year perpetual calendars work. Regular perpetual calendars will need to be manually reset in the year 2100 due to the additiona...
Is it Safe Buying Watch Parts from India?
zhlédnutí 1,2KPřed 5 měsíci
The easiest way to repair a broken balance spring is NOT to make one from scratch using a $50 "raw" replacement hairspring, a $10,000 hairspring vibrator and a $5,000 balance spring outer coil cutter and spending two to three days installing it, but rather to simply buy a spare movement for $10 and swap out the entire balance assembly, including the balance spring. And that's exactly what I do ...
A Vintage Watchmaker's Hairspring Cutting Tool
zhlédnutí 1,1KPřed 5 měsíci
In this video I explore the features of an adjustable vintage watchmaker's hairspring cutting tool and go over every detail of exactly how it works. Technically the correct term for a mechanical watch hairspring is, "balance spring," but somehow "hairspring" is a much more fun (and certainly also accurate) description of these tiny wonders! 😂😂😂 I purchased this vintage watchmaking tool, like my...
Patek Philippe 16-250 Movement Gets a New Case
zhlédnutí 1KPřed 5 měsíci
In this video I recase a Patek Philippe 16-250 movement and cobalt blue Golden Ellipse dial that I bought used for $400 over a year ago. The solid silver case that I recently found for it for under $100 was made by the Italian jewelry maker Fope in the 1970s and is a perfect visual match for the Patek Philippe movement and dial. I had to make several structural changes to make this movement cha...
DIY Hardening, Tempering and Annealing Watch Screws
zhlédnutí 902Před 6 měsíci
DIY Hardening, Tempering and Annealing Watch Screws
Making a Replacement Screw for a Micrometer Using a Watchmaker's Lathe
zhlédnutí 14KPřed 6 měsíci
Making a Replacement Screw for a Micrometer Using a Watchmaker's Lathe
Watchmaker's Lathe Restoration (Fail)
zhlédnutí 2,7KPřed 6 měsíci
Watchmaker's Lathe Restoration (Fail)
Sharpening a Graver for a Watchmaker's Lathe (the wrong way)
zhlédnutí 623Před 6 měsíci
Sharpening a Graver for a Watchmaker's Lathe (the wrong way)
"Making a Stem" 😂 for a Patek Philippe 16-250 with my New Lathe
zhlédnutí 1,2KPřed 6 měsíci
"Making a Stem" 😂 for a Patek Philippe 16-250 with my New Lathe
Wolf Jahn Geneva-style 8mm Watchmaker's Lathe
zhlédnutí 8KPřed 6 měsíci
Wolf Jahn Geneva-style 8mm Watchmaker's Lathe
Petermann Freres & Co Escapement Meter
zhlédnutí 773Před 6 měsíci
Petermann Freres & Co Escapement Meter
What's the Best Watchmaking Lathe Setup? Questions and Answers from JD Richard's Chat Group!
zhlédnutí 582Před 7 měsíci
What's the Best Watchmaking Lathe Setup? Questions and Answers from JD Richard's Chat Group!
Mercury Felsa F 760 4K Multicam Eleven Hours
zhlédnutí 419Před 7 měsíci
Mercury Felsa F 760 4K Multicam Eleven Hours
FHF Robert Ligne 10 5''' Restoration in Twelve Minutes
zhlédnutí 558Před 7 měsíci
FHF Robert Ligne 10 5''' Restoration in Twelve Minutes
FHF Robert Ligne 10 5''' 4K Multicam Twelve Hours
zhlédnutí 358Před 7 měsíci
FHF Robert Ligne 10 5''' 4K Multicam Twelve Hours
Full Restoration of 1921 FHF Robert Ligne 10 5''' Wrist Watch (Edited Version)
zhlédnutí 698Před 8 měsíci
Full Restoration of 1921 FHF Robert Ligne 10 5''' Wrist Watch (Edited Version)
Changing an Incabloc Setting in a Vintage ETA 2783 Watch Movement
zhlédnutí 3KPřed 8 měsíci
Changing an Incabloc Setting in a Vintage ETA 2783 Watch Movement
Traditional Watchmakers' Pivot Polishing Tool
zhlédnutí 1,5KPřed 8 měsíci
Traditional Watchmakers' Pivot Polishing Tool
A Box of Vintage Watchmaking Tools and Parts from G & J Watch Repair
zhlédnutí 6KPřed 10 měsíci
A Box of Vintage Watchmaking Tools and Parts from G & J Watch Repair
Rolexes, Radium and Atomic Clocks - Family Heirlooms in the Nuclear Age
zhlédnutí 1,3KPřed 10 měsíci
Rolexes, Radium and Atomic Clocks - Family Heirlooms in the Nuclear Age
IWC Cal 44 Watch Balance Staff Replacement
zhlédnutí 429Před 11 měsíci
IWC Cal 44 Watch Balance Staff Replacement
IWC Cal 44 Watch Balance Staff Removal
zhlédnutí 448Před 11 měsíci
IWC Cal 44 Watch Balance Staff Removal
Vintage Watch Auction Prices in Switzerland in 2023
zhlédnutí 775Před 11 měsíci
Vintage Watch Auction Prices in Switzerland in 2023
Using a $4 Junk Watch to Restore a $450 Swatch Prototype
zhlédnutí 848Před rokem
Using a $4 Junk Watch to Restore a $450 Swatch Prototype
Amazing 👏🏻👏🏻👏🏻
Thanks! I'll be publishing a proper video about using this soon!
👏🏻👏🏻👏🏻👏🏻
Woah that's a really nice looking Swatch
That's a Swatch Chrono Goldfinger!
@@IMakeWatches Awesome, thanks!
Loosen the screws on the shaft quit hitting the shaft
See 20:06. I think you may be right but my recollection is that pounding it with a wood block and a mallet did work in the end. I'm on to another lathe altogether now anyway, a Boley B8. But it has the same problem. 😂😂😂
You need to sharpen graver
Thanks! Yes, I figured that out and went overboard buying sharpeners and more gravers! I think I've got it now!
Canon pinion puller all sizes
Can we change broken top Glass?
Yes! There's a list of watch parts vendors on my website imakewatches dot com. Several of them sell the crystals. I buy them from Cousins in the UK because they have a large selection. The key is very carefully measuring the broken one, or measure the opening and add 0.1 or 0.2mm so that the new one is slightly larger than the opening and when inserted won't fall out. And then having a simple tool to help insert the new one.
Thank you once again for a most interesting informational video. Wonderful machine. However, not practical for our hobby. Not enough space to facilitate working on a movement. At least, that's my observation. Keep up the good work.
Yes, it's more for inspection than working under!
The scale of the model seem humongous! 👍
It's larger than an easy chair but smaller than a single bed. I was fascinated by the pincers around the escape wheel pinion. Those pincers are no longer a feature of the modern Swiss lever escapement. I think that the original 1754 design attributed to Thomas Mudge may have had those as a safety to make sure that the fork couldn't jiggle into a position where it jammed. If you or anyone else has additional information (or theories) about this please feel free to add a comment about it!
Lovely escapement model -- sounds like it could use some oil though! 😄
Yes, that's the sound of metal on metal at scale. They either need to lubricate or swap out those chrome pallet stones for ceramic ones (or both).
Escape from reality. 😎
Escape from the illusion that ephemeral temporal audiovisual juxtapositions created to sell products and ideas are more important than reality! 😂😂😂
I poked around a bit for pricing and didn't find any info. Just out of sheer curiosity, could someone please reply with a rough price range for these?
Sorry for the delay answering you about this. Please reach out to Yuksel directly for pricing info. The microscope is very affordable compared to others with similar capabilities.
@@IMakeWatches OK, Thanks. I guess I asked you for a general price range rather than the company, because I wouldn't want the company to hope I was a potential customer....I was just curious. I really enjoy your content. Thanks for making it.
Would love to see it in operation
Yes! Me too! I also would love to open the glass case and take the time to try to figure it out. It's crazy how complicated some of these old tools are!
What an amazing collection… And the space, lighting and overall ambience are terrific. Lucky that there were so few people there. Those skeletonized pocket watches looked like they were made of lace. Thanks for the tour!
Thanks Mike! I added chapters so if anyone wants to jump to the skeleton watches just check the chapters in the description!
You should go to the one in Le Locle !!!! It has more clocks than chewy fronds does, but is much more intimate and I preferred it
@@christiankirkenes5922 Thanks! I’m actually there now! And I agree with you about the intimacy! But I need to get permission to come back another day with a tripod to make a proper video.
@@IMakeWatches That home made monks clock on the ground floor is amazing, I love how he just adds another level every time he wants another complication XD There is also a very good watchmaking school there on the other side of the valley.
@@christiankirkenes5922 Yes, that monk's clock is insane! It looks like no other watch or clock I've ever seen! Like you say it reminded me of software or something more modern architecturally both in terms of the stacked nature of it and the fact that it looks like a series of hacks in black boxes.
Hey I was there about 2 months ago !!
la france die LIP ! Fred LIP.... lovely museum next week i go with my dad to my fatherland to look at Casa Pia in portugal !! Only two months i start watchmakers scool and work place at kalle slaap my dream is comming true...sry but iam gonna watch again thnx Dayton!!
Wow! That's super cool about working for Kalle! I'm jealous! Have a great time in Portugal ElderPinto!
@@IMakeWatches dont be its all for free not a payd job but i need papers and i need work somewhere do get experience. i am jealoes of your camera setup lol
Many thanks for the tour.
Sure! Thanks for your wonderful videos! I watched your Gerald Genta video a while back and I've now added your channel to my featured channels. For anyone reading this comment please check out @thewristwatchexperience8153
Dr Evils lair !!!! who knew he was a fan of timepieces !!!!
What an amazing museum ! And its practically devoid of guests ... wow ! Thank you so much for sharing this with us 🙏
Thanks for watching! Museums are a challenge to make videos about when most of the objects that they contain are is so tiny, but I figured that it was worth a try!
Super neat. I bet that museum is amazing just in general.
Yes, I could spend days in there! I will have to go back soon because I also went to the museum in Le Locle just six minutes away and it was also amazing but I didn't film there. I wanted to show them this film first and then ask permission to go with a tripod etc.
@@IMakeWatches oh wow, yeah that would be amazing. Hope they allow it - I can’t wait to see what you shoot!
What a beautiful machine! I love the long belts hanging down... almost looks organic.
Yes, there's something interesting about the contrast of the soft belts and these very precise metal machines! Like tendons and bones.
Human ingenuity never ceases to astound ! Thanx for sharing
Thank you for commenting! I wish I could make a more in depth video about this machine. Perhaps in the future.... It is crazy complicated! Especially considering that "all" it does is make tiny screws. On the other hand modern CNC machines made by Tornos like the Swiss Nano are the size of a small car, so by that standard this machine is tiny!
Wow! You have SERIOUSLY gone off the deep end 😂. I had no idea you’d built up a collection like this - is that a topping tool I saw in the background? Incredibly cool!
Yes! I keep thinking I should make a video just for you, Chris and JD about my progress. I just feel like I need to do something impressive with it and I'm not there yet. I did make that gear blank with 60 teeth that you can see in this video (with an index controller that I made), and I have the cutters to try to shape the teeth with the topping tool, but I don't really want to make a video about all of this until I can make two specific gears that I need for a specific pocket watch so the video results in a successful restoration.
@@IMakeWatches holy cow, that’s amazing, I’m so impressed with your progress! I totally get it about the video - I’m happy to wait for as long as you need but very excited to see the end result!
It's ALIVE! IT'S A-L-I-V-E!!!!!! 😁⚡️
No Please! Sharpen that tool, it already looks like a file. Jajaja
I did! Thanks!
Please gentleman, i´d like to know what´s the serial number(in the Eternas) that shows the year when the watch was made ? the one that is on the case back or in the caliber?? Thank you. By the way that´s a beautiful Eterna watch.
Thanks! I don't recall where I found that info off-hand, but you should be able to find it with google.
That Bermi has great potential, did you restore it?
Thanks. I cleaned up the case a bit but I haven't done anything with the movement. I do love the design and especially the clear caseback!
Be careful with radium especially when the dial is open
Thanks for this comment! I agree 100% about being careful about radium. Anyone reading this that is thinking about opening any vintage watch, please take the time to research radium and get yourself an inexpensive Geiger counter before opening ANY vintage watch so that you know how to identify radium and how to protect yourself beforehand. Almost all watches before the 1960s had radioactive paint on the dials and hands, and that material is dangerous if ingested or inhaled, and it has often turned to a combination of dust and gas inside the watch. It's best to become an expert on this before you open the watch rather than after because the radium dust can get into your bones and stay with you the rest of your life if you're not careful.
Really nice detail and effort invested in to such a video! Do you know which main spring winder to be used for the main spring?
Thanks! I got a Watchcraft set from a retired watchmaker in New Mexico and one of them works but I can't tell you how to source that exact one out of a set. You can see that set in this video czcams.com/video/HlukABmdcjY/video.html. I did also buy a single one on Aliexpress that was listed as being the right size for ETA 2472 and I trust it't the right size but I never used it because it was defective. I think it was around $40. It was more of a Bergeon style with the tiny crank. You could also see if bergeon.swiss sells individual ones. I know they sell sets but they're very expensive. Sorry I couldn't be more helpful! Good luck!
It is difficult to become interested by modern watches after looking at these beauties.
I totally agree! The only interesting modern watches(in my opinion) are the ones being made by hand by independent watchmakers and they cost a fortune. Check out MB&F if you don't know the brand, and the Rexhepi brothers, Rexhep and Xevdet!
I have a gold Seiko Bell-Matic that is still in excellent condition, hardly any wear of the gold plating.
Fantastic! I love Bell-Matics!
Looks like you found the right technique at the very end (collet side down, small flat faced punch to the safety roller). The pivot could have broken off at any point with all the fiddling around. It's a sick feeling when these kinds of things happen (I know from experience!). Don't be discouraged though! Like you said, it's part of the joy of watchmaking. If it were easy, everyone would be doing it. Just keep practicing and keep learning... just know that sometimes a good education is expensive... Cheers ;)
Thanks Chris! I'm obsessed with making my own parts now - in large part as a result of your videos. I'll get back to disassembly / assembly after I can re-make anything that I destroy. This balance staff will be part of that process as I'm down to one now.
or you buy a vintage staking set. I use K&D myself
Yes, I ended up getting a couple of Star staking tools! I think the K&Ds are more common in the US and Star is more common over here.
czcams.com/users/shortshVdXKa4dKsA?si=tcaQHLGf-adN7d7p
Use a screwdriver on the ratchet wheel!
Thanks for this comment, Mike, but are you saying that I should have used a screwdriver, or pointing out that I shouldn't have? Corrective comments are welcome, particularly if you think it will help others, and don't hesitate to mention the time in the video that the comment applies to.
Just use a screwdriver to hold and slowly release power on ratchet wheel if stem is not there.
Got it! Thanks! 😂
you, JD, Spinner and retro watches are the best watchmaking channels on youtube. you a fast learner and a great teacher. grumpy watchmaker is awesome too
Thanks! I totally agree with all of those except myself!
@@IMakeWatches your channel is to show others like me the struggle you faced and how you fought through it and how good it feels to overcome and that is what i know as inspiration. its been to long man i need ya
@@hellothere312 😂😂😂 Very kind of you! 😂😂😂
Superb tribillion
Technically that's not a tribillion! It was however, trihundred ($s)! 😂😂😂
Amazing.
Yes! I saw yours finally! How do you like it? I think you underplayed it. It was cool looking around the frets!
I love microscopes in general. It’s amazing how technology evolved in our lifetime.
Thanks so much, Dayton. It was great to be interviewed and featured on your channel.
Tebrikler Yüksel!
Soooo....Dayton....we going to see one of these in your workshop? I've never seen a product and a customer so perfectly matched. 😀
I agree with you that it is perfectly matched with my interests and skills and I would love to have one. However, it's an inspection microscope, not a bench microscope. There's no reason why it can't eventually be agile and automated enough to stay out of the way on the bench while constantly seeking the best possible view of the subject (how cool would that be!?) but for now it's better suited for watch photography studios like @TeddyBaldassarre and watch manufacturers that have a regular need to make detailed inspection videos and make live measurements than it is for watchmaking vloggers like me. Actually, now that I think about it someone like Mike or Chris - or anyone better organized than I am that makes their videos shot-by-shot, could definitely use it. I just feel like my channel is all about the bench right now and that means that all of my cameras need to be clear of my work areas. Another interesting possibility would be if if could be controlled by foot pedals so that it could be used on the bench and moved from position to position even while both hands of the operator are engaged with tools and workpieces. Because it can move from Position A to Position B automatically this could actually work very well! Hmmm.... maybe I need to talk to Yuksel about this! 😂😂😂
@@IMakeWatches There's so much consistent positioning with the standard disassembly / assembly work I'm sure a lot could be covered with pre-set moves. I notice on Chris's work he's very good at keeping the watch movement in the same orientation I'm forever shifting mine, makes the edit opportunities fewer, but even so I find myself switching between camera 1,2 & 3 at the same points
@@IMakeWatches Thanks Dayton and everyone. I am very new to the watch industry, I designed the system initially for the chip/semiconductor industry. But it's a flexible system, and the software will hopefully evolve to meet different needs. The foot control is a very interesting idea. I have no clue if it makes sense, but we may even consider a VR headset for a fully-immersed hands-free experience. Yes, let's discuss. I will gladly send you a demo unit for testing :-)
@@yukseltemiz Wow! Thanks Yuksel! Let's discuss by email!
wauw awesome and amazing to see !!...now back to my bunker buildt!!!
Brilliant product, and process to get there!
Wow Yuksel, your product and backstory is so inspiring! The thought of a programmable robotic microscope is causing so much creativity in me right now! I am a watchmaking CZcamsr, photographer and technology geek, and I can think of so many other industries that can benefit from what you've created. Dayton, this was a fantastic interview and video. Kudos to you both! 😄
Thank you very much Mike!
whats going on ?
Sorry, I accidentally used music that was not rights free so I had to re-upload it!
@@IMakeWatches Bad Boy !!! LOL you could use this system to view escape functions.
Very nice very hard work...
Yes, thanks for your comment! That was a lot of fun!
Thanks for sharing part of your collection, really some great watches you have there.
Thanks Pipo! I think I said I'm not a collector in these early videos but over a hundred watches later I probably have to admit that I am. That said, I keep going lower in terms of price because I perfer older non-working watches now!