Video

Made a mistake a poured engine oil in the yellow oil fill plug under the bed Was wondering where I should drain it and if this will cause damage ?

I’ll mortgage my house if you come fix my refrigerator … 😂

Hi thank you for the video. Have you ever encountered the suction line freezing up after recharging the refrigerant?

I think your pliers had a crimper on them

So, where's Part 1??

How did you seal the cooper tube that you Pierce ?

I have a less than 2 year old ge fridge that makes a lot of rattling sound, Several techs have worked on it and ge says this is just a normal sound, the coolant boiling thru the line causing a rattling noise. I think the tech that serviced it was a little goofy, Is there anything I can do, GE sucks and will not fix it.

This is by far the best video I've seen on servicing these machines.

Great video I made the a/c connector but the compressor fan not running Your thoughts

Is there only one drain for the auxiliary hydraulic? Or, Is there a drain on the bottom side of the hydraulic pump? Similar to the transmission case?

May I have the part number of the relay, as showed at 16:50 ? Thanks!

Any comments on why it is difficult to put a 2015 900 into and change gears? Great video thanks

2008 GE Profile 22 cu ft unit stopped last week. Replaced start and run capacitors $200...fridge stayed at 65F ..freezer at 10F all day; overnight they went to perfect at 36f and 0f. Then..all week stayed at ~65 and ~10; reset thermostat...no go; suddenly today looking good at 38f and 2f...and stabilizing. WHAT is going on here???

Thank you for this explanation. When you use the vacuum pump to clear the system, is it clearing just gas out (air + refrigerant vapor) or is there liquified refrigerant? If so, where does this pump out to?

Bravo! Very impressed. I don't have all those tools, but I will be looking to get those tools. Thanks for posting. Refrigerant...huh! I wonder if you ever found the leak, since it is very small?

I am a fan. I loved the technical details, the schematics of the compressor, the subtle dry humor (I laughed out loud..."remortgage your house"...lol). My refrigerator is not cooling and the compressor is running, so I'll be watching part 2, to see what you discovered. Thank you for posting this video. You are a treasure.

Very well done. Clearest instructions for this i have yet to see.

Hey what oil do you use for the engine And what oil do you use for the hydraulic system and transmission system. Can you also tell me how many liters for in all listed above. Cheers great video! Subscribe.

Great source of information, thank you for doing this. Very detailed and well documented.

Your jumpstart tutorial is gonna get me by until my relay gets here. My freezer full of meat is saved! Thank you sooooo much! 👍

Very good video. thank you

Please don't take my comments as a complaint.I loved your video and thanks for a detailed video for such a bigger problem in refrigerators @8:30 minutes of your video you purged the blue and yellow pipes but again you opened yellow one for UV liquid pouring,so did you vaccum the compressor again or did you allow a small amount of air from the yellow pipe😮.

Thank you, just inherited an X1100C, that looks like a lot of work. mine has 340 hours on it, and no clue if anything was ever done at all for it???

Excellent! Yep! Better than a manual.

Wooow, Great videos on both Part 1 and Part 2. You know what you are doing guy. Most importantly you are sharing it here so to help people. I appreciate for taking your time and put theses videos together. The content is fundamental and makes sense. I am going to jump my compressor just the way you had showed. Keep up the great work!

Did you finally fix your unit, and if so, what was the issue?

What was your final diagnosis

Is it safe to say that the piercing valve stays on the copper process line?

This is an excellent video and very helpful in explaining that the transmission fluid is separate from the HST tank (although it all uses the same type of fluid).Nowhere is this explained in the owner's manual. The same is true for your demo of changing the coolant. My question is: Is it safe to use a car hoist to lift at the frame rails?

Thanks a ton, getting ready to do my first 50hr service on my 1100c this will help tremendously!👍

Great demonstration. Thanx

thankyou very informative video, i just bought a RTVX1130 and I love it. I will be watching your video to learn more, again thank you!

Is that Automotive R134a Refrigerant ?

You let air back in the line after you purged the line. The lines must stay connected.

Yes, I believe you deserve a award for the effort you put into showing all of us how to maintain our 1140s Excellent video

very thorough but what are the hours intervals for the different items like engine I'm sure is more frequent than hydraulic or coolant

thanks for the tip

We used Fluke multimeters in my shop in the military. I also highly recommend them.

When the wiring diagram was shown, it took me a minute to realize there was a very small cursor tracing the circuit path. It was hard for my old eyes to see it. Could you add a larger, more obvious for us old heads please?

Is there anything that should be done differently if its a dual zone refrigerator?

wow. you deserve an award for this video. Thanks for making it. I never knew the HST oil was in the tank. I thought that was for the steering and lift cylinder. I have 500 hours on mine and never changed this oil. looks like I'll be doing that ASAP. Again, great video that was effective and straight to the point. Oh and I also didn't know about the front driveshaft lube point.

Good job.

how did you pull out the refrigerator

Just bought one today. Thanks for the informative video. Excellent.

Excellent video. I just saved this to my favorites list.

What oil goes in the transmission? You said it’s basically gear oil but looks like you put hydraulic fluid in

awesome video thank you

You must be on bare metal and confirm you have a good spot by ohming ground to ground. Touching the top that is painted will give you false readings.

How about checking the hydraulic tank suction strainer before refilling.

What are the cross reference filters - say to Fram or other common brand - I am not near a Kubota dealer.