Video

I can’t find this brackets. We’re can I order them or what’s the part number on those brackets.

Not a professional way to route the harness.

My roll-back cover will not roll all the way back in ..does anyone have an answer to the problem..the canister is clean.

no link to the item lol

My ultagroove cover has seperated from the pull rail, the rail that the pull rope is attached. It appears to have become delamenated from the canvas top. It appears to be held by contact cement between the rail and the canvas. Can I repair it by relaminating with contact cement. Otherwise looks like i will have to use bolts to secure the canvas to the rail. T IA

Where brackets from?

Can the license plate still be attached in front of that or will it have to be moved somewhere else

Hi, my son has a 2024 Colorado. I scratched the gate cap. How i can i repair that scratch?

How do we uninstall the trackrac rails?

So you just leave the front shield with a clip at the front, 3 screws at the top, but hanging freely toward the backside? Yeah that’s going to make some noise while driving.

just think if you could really get it in a few day... In 11 years it takes 4 Weeks to get one..

Berry nice thanks for your help

Is the seal supposed to sit on the tailgate or in front of it

Just did this on my 2015 Tacoma trd sport, works like advertised. The metal arm and bracket that the solenoid pushes squeaks a bit, probably would’ve been ideal for them to be made out of brass rather than stainless.. figuring that it’ll wear down a bit over time and hopefully make the squeak stop. If not I’ll pop the tailgate open again some day and maybe put some Teflon in the spots it’s squeaking , idk 🤷‍♂️

I bought one of these for my 2015 F-150. Looked great! Worked well. Waterproof, too. 3-4 years later, the paint began to flake off. Now (8 years later) it looks terrible! I don’t see any bare metal yet, but it’s probably not gonna be much longer. Still waterproof. Still working great.

What size is the signal bulb?

What size are the backside nuts?

If i have a 2inch strut lift kit and install a 4" lift spindle will it raise the truck more?

What about installing on a 2001 silverado 3500?

Which Yakima rack system fits on this ?

What is the part Number for the Tag Light Used in this Video , the one I bought is to small ??????

How long does it hold the ice

Where can you buy the replacement seal?

How much does that cover weight?

Thanks for the video, it was a great help, I just finished installing mine and the step-by-step directions was dead on, thanks again

Am I the only one who thinks these are a waste of space? I guess you would have to have a specific truck for that. Otherwise I feel like it takes up a lot of use from the bed

I was able to take off and on without un bolting the bed. It was tricky though like the transmission pan. This video shows that it can be done. I have to do it again though let's see if I can do it a second time. 2015 silverado.

if anyone is watching this to figure out what size bolt you need so you can tap into the factory tonneau cover holes, it's M6x25. It is not an M8 bolt.

Now do a video where you can easily rip it with your bare hands and no tools.

Good work. Claro y al punto👍

Any video on how to change the corner piece on the bed rear cover ?

Does anyone know on how many years an tonneau covers last ?

Wheel setup please!?

What do you have to do to replace the light.later on.

Can you order for a 1999 Dodge ram 1500

How do you replace the rubber seals along the length of the side rails?

Advantage tonneau

Do you happen to know if the Vengeance rear bumper is compatible with Rigd't UltraSwing Mega-fit?

My Lo Pro should be here tomorrow 9/5/23 to install on my 2011 Ford Ranger. I’ve been asking my wife for a tonneau cover for our Ranger since we bought it in 19, as the bed fills up with snow every winter. I have to put 260# of sand bags over the rear axle for added traction during our very cold snowy winter months. We live in a very mountainous area of north central WA state and get 5-7 feet of snow every winter. Our pickup is a 4WD. We’re 5 miles from town and 25 miles from the city. Two years ago we had a big snow storm move into our area. The city had no snow prior to the storm but we had 2 feet on the ground. When that storm hit, we got 3 additional feet in 10 hours, whereas the city had only 1-2 feet. Next year we’ll be building an additional garage for the pickup. It will be installed and heated to 40 degrees F. Our over sized attached 2 car garage is also well insulated and it never gets below 40 degrees F. Believe me when our daytime temperatures are around 25 degrees F, 40 degrees F is nice to get into.

What’s the difference between the Lo Pro and the Lo Pro QT?

Thank you for sharing this video! It really helped me troubleshoot a wiring problem that I was having!

Can you close the JackRabbit cover from the side of the Truck or by the strap only?

In my case, the stock cap prevents the door from closing on my truck cap.

hi there, power actuator question, i dont have a fob for my f150 i lock and unlock it with keys or the keypad, will that still operate the power actuators on the toolbox or is it oly with a frequency

thank you. this worked for me.

mark with a felt pen the underside of the alloy side steps through the bracket bolt holes, save a load of hit-n-miss attempts at lining everything up properly,

was wondering if anyone had a part number for this kit. even the local dealer here cant help

Way under-manufactured. Most of these steps could've been done at the factory. Thank you for taking the time to make this video!

I have a mostplus tonneau cover for my 2001 chevy Silverado 1500 the rear clamps do not close due to the bed having a shaved lip toward the rear of the bed. My installation guide doesn't show how to use the rear clamp hook, I was wondering if this video is the same fix for my issue? Do I remove from the shaft and attach it like shown in the video?

Good video, but you didn't clearly show all the products.