Video

Hi Peter, thanks for this presentation. Can you show to convertion of a metric value 1 kpa to 0.145 psi. Thank you.

I’m confused. Is the same power source going through the contacts and the coil?

GOOD VID THANKS

Nice One

Thanks @PeteVree. More power to you. God bless

Phase» is a confusing word. May mean: 1) A voltage 2) a conductor 3) a phase angle between two sinus waves. One never knows, take your pick.

where I can buy this Labvolt Models

I subbed and do you have a video about common and seperate control?

Awesome video! Thank you!

This instructional video rocks. Others should follow the lead.

Thank you very much!

Would a 6ES7 212-1BD30-0XB0 work for your course, or would we need something with more capabilities?

Do we apply DC for power factor correction?

Where you get these text boxes?

If for some reason i lost my youtube account, and made a new one you would be the first channel i would subscribe to again, i really appreciate you sharing your knowledge sir!

In tia portal v17 .fwf file not find in the folder of said address Kindly suggest

Hands down one of the best explanations of time delay relays I've ever seen.

What is screwing me up is the #5 wire, shouldn't it go to something separate that closes the holding contact? I think I just figured it out lol. Ok so when the coil is energized it closes not only L1 L2 L3, but also the holding contact?

Thank you very much for the explanation, very helpful 🙏

please can anyone send me this plc ladder logic to my email?

can you give sample with open delta loads with different resistance load?

I❤️you. ☺️thank you!

thanks

GUYS PLEASE TELL ME HOW I SHOW THE CONTING OM HMI, I have a counter on twido suite and need to show the counting on hmi

thank you for the Tutorial

The dogs bollocks in electrical theory

Thanks i am a Sophomore of Electrical power engineer I try so much I want to be an engineer Thank you so much 🎉🎉

You just save me thank you sir

The way he explained it the wiring in the video for the high voltage is wrong then you should probably relay that to everyone so they don't get confused other than that really good video

Thanks Pete, for nice explanation

man ur video series is so crazy good

👍👍

Sir i have a golf vehicle when i press pedal single time it can not move so i press pedal many time then it move and the smoothely run but the only problem is that its starting torque is very low because batteries are fully charged i check input voltage of motor 48 volt dc exact i want to increase motor starting torque what you suggest please reply its humble request

I'm a residential electrician which is nothing compared to this and slowly I started accepting my truth at class that PLC requires more brain than what I have but you're videos are giving me hope, you're way of explaining is making sense to me finally, TY! 2 months away from graduating

230V/400V is better...😉😆

your tutorial is useful but i needed idea on how to set up the usb 4750 using driver , i have downloaded and installed the driver and SDK of DAQNavi , but the driver is not being recognized by device manager , pls help

thank you

I have a small motor like this but its not wired this way where the windings have a long jump line. The two windings are connected together but kept separate by the brush and armature. I think its way less confusing to be wired that way since the way its wired on the diagram is the way its wired irl. Whereas in the vid that jumper wire can cause some confusion.

So if we change the number of windings could we change the voltage ratio from sqrt(3) to 1? If so could the windings of each transformer pair be different and each have their own ratios?

Can you add 2 more lights in rung #2 and have them flash with flashing light 1?

Hey can you do a detailed video of wiring up a three phase reversing like you had in the wiring schematic with the large black motor control you showed in this video @11:40? This is what i have to do for my test at work.

This video connected the dots for me, literally! Taking it from ladder to schematic was awesome. Thank you very much.

Best explanation. Wish you best of luck.

Many thanks 🎉😢❤😊 4:53

Many thanks 🎉😢❤😊

Awesome information. Thanks

A partir de que versión se puede editar, yo tengo la 30 y no me deja

Very good I will try it in my SLC micro logic1000