Video

Iron

Hammer and bolster would have had that cut in 10 seconds

コテ要らずっすね〜😂😂😂👍

What was your mix ratio bud?😊

Buzz you are wee legend!!!

I had that hammer when i was an apprentice i was told my the contractor and the old timer to buy a wooden hammer

I think I'd be happy with a cut joint

I just use a grout bag. Tool and brush.

I always just use a grout bag and my mortar is wetter than what you're using. After it dries to my liking, then I will finish tooling up the wall with my hand jointer, brush and then re tooling it all with my hand jointing tool.😊

Old school - Yee ha! 🤠

I always butter both sides of the sliver and both sides of the gaping hole before I lay the bloody sliver 😊

All in the detail 👌 keep going great work

We’ve just started doing on site, Barratt homes. With the doors incheck.

Why not make a "V" mortar I the cavity & press the sliver down into it?

You could still see the sawdust from the pilot hole😅

Looking good usual proper job have you tried using lorry fan belt as a rubbing tool i find it just a little more fllexible can follow the contours of the brick edge a little better different widths gives you a nice flush finish.keep up the fine work

We still build like that in Ireland no window or door formers over here 🇮🇪

Not knocking you bud, but why not lime? Don't give me its what the client wanted 😂

Is this a pre bagged mortar you are using, Budd? Or is your local sand perfect for the job? I've tried using mortar guns in the past, but the sand we have up here in the Highlands is nowhere near fine enough.....the gun gets clogged within seconds.

them guns last for ages but as soon as it blocks dont try and force it through clean the gun and some fresh mix in it

is it best to use plasticiser too was thinking doing 4 sand 1 cement should i use soft or sharp sand does it matter

Nice one Budd. I did my patio pointing using the same gun ( not yours-my own 😜) . What i did was get a plastic funnel and place on the empty end and mark round with a sharpie. Then cut the circle out a bit smaller. Drilled a couple of 5 mm holes and screwed in some long bolts with 2 nuts each. To fill the tube put funnel over the end, hold down with two fingers and slap the mortar into the funnel. Give the whole thing a sharp tap downwards and the tube fills up quickly and solidly. Its not only you boys in the mysterious east that have good ideas. 😄😄😄

Old school using metric 🤔

Bag for me I like the look

Butter both sides of split , we used 150mm dpc and left 25mm out, when door frame fixed from inside it formed a water barrier.

Grinder so close to your feet too 😮

I wonder what’s stopping the damp.

Very very dangerous......18 rated 😮😮😮🤠

Clearly wasnt level

How you getting the ballast and cement off the grass afterwards?

That hole was pre-drilled bro

You moved the marker as you marked it good thing mortar covers the mistakes

Lmbo. All that measuring and straight edge to end up eyeballing it... lol

足元注意っすね！👍👍

Crap ,, zero muck against other block … totally shit

I like the drywall as a substitute for the mortar bed while getting your measurement.

Thats terrible, no mortar on the one side, youll never be able to get a full joint there

Budd there’s a checkout at Tesco waiting for you m8 😂

I've got my dad's old black and decker corder drill from about 1980 still going strong. No hammer action and chuck needs a key but it has it's uses.

Iron every time .. and definitely not bagging up for any face brickwork.. bagging up for manholes only..

Ok so i saw 3:13 go in there, or did i miss something in the video edit between head cam and guy with the tripod?

Don't touch the muck with your hands, looks amateur!

Don’t think I’ve ever seen you use perforated bricks

I'm no bricklayer but I have work cement, It's brutal on the skin. So why no gloves

Proper job all joints full old school love it

Looks like a good strong mix,not too much water

Sorry mate your not a bricklayer why are you showing this shite.

How can an improver teach a beginner 🤔

If he has to say he has a Mans hammer, he has a tiny nail..

Great video. Curious, what's stopping you from just drilling holes into the brick and use that as an vent? Save you the hassle of removing it to install the air brick. Would it be structurally unsound?