Video

It just says it’s in economy mode

I also didn't remember to tell you where your screw driver was!!!

Hi There, When the heater element goes to ground it shows the insulation has broken down, the spa is dangerous and should not be used as electricity can connect to the water. The heater needs to be replaced. See here. poolnspa.net/shop/heaters/sp800-heater/ I also have SP600 1.5kw heaters. (same price) Just order at the link above and put the note sp600 1.5 and we will send you a replacement heater tube. That is new sensors tube and element, Mark. Also see this czcams.com/video/IG-JAtsBinE/video.html

There are a series of videos here watch the whole playlist to understand what is happening here. The mismatched tyres create a jolt in the drive train. Not a wobble on one side. That sounds more like a tire fitment issue or a balancing weight has come off. Take it back to where the tyres were fitted and get the balance checked. MRT

@@Marksreviewsandtutorials maybe I didn’t explain my self well ,what you are saying in this video about acceleration and then like a few hits like something is loose feeling ,I have it like when I take off then goes away and if I accelerate to hard I also feel it then goes away

@@rubengalvao856 Watch this Playlist I believe it will help you. czcams.com/play/PLRRErA3V0MY0vvfEq8GeRrakmw9QPLuZ_.html

I did take it to the shop and made the balance and weight check everything is alright, but stays the same

Hi There The Davey three speed blowers are gone, no longer available. These blowers can fit straight in place but will just operate as 1 speed. poolnspa.net/shop/lx-blower/ It is a combination of both that make it three speed. If you are changing your Spa Controller as well do that first as it will determine the style of plug needed on your blower. Give us a call at PoolnSpa Supplies Australia www.poolnspa.net either to buy a blower or a new controller. We recommend different controllers depending on your spa and particularly how many pumps and blowers your spa has and what you are replacing. Our pricing is very good. These things are pretty complex and we are happy to chat through when people buy from us and make sure you get the right product, that is safe and will work. Mark PoolnSpa supplies Australia

@@Marksreviewsandtutorials Thank You DIdn't know that

Yes you can also replace the heater tube assembly, see here czcams.com/video/IG-JAtsBinE/video.htmlsi=H27Idf9JQjb8J2Qo If you fit a heat pump to the spa you normally disconnect the element heater. Give us a call at PoolnSpa Supplies Australia www.poolnspa.net either to buy a replacement heater poolnspa.net/shop/heaters/sp800-heater/ These things are pretty complex and we are happy to chat through when people buy from us and make sure you get the right product, that is safe and will work. Mark PoolnSpa supplies Australia

What do you base that on? What have you experienced or who has advised you? It has become common practice and considered the only way to go to change more often. Time has shown all types of problems coming on cars that went the full distance and way less with more oil changes. The oil is breaking down. MRT

I have also put an old rubber car mat under them too and that worked a treat. MRT

If a little stone gets jammed in there it can get awkward. I would get the lid as loose as you can and then spray with a jet of water from underneath as much as you can. This should make it easier to get off. Apart from that just keep at it, wiggle and lift from different directions until you get it. MRT

@@Marksreviewsandtutorials realizing that in your video there is actually 3 ways to put it on - due to the 3 parts to the cam lock. The right way, the way you did in the video and the way mine must have gone on - basically 120 degrees difference from the other two ways. No stone in the way though. Just that notch in the cam lock that preventing the left side from releasing.

Yes they are all still going strong. Get in contact with PoolnSpa Supplies Australia to sort the best fit. there are a few different types, so important to get the right one. poolnspa.net/shop/light/agrx/

Yes, it does make the seat better over a range of body sizes.

Glad it helped

There are four videos here in this group, see the end screens at the end of the video. Watch them and you will get a good understanding. basically all 4 tyres need to be the same rolling diameter. Watch the videos it will save you lots $. Doesn't have to be run flats does have to be same rolling diameter.

@@Marksreviewsandtutorials hi yes I checked and they have the same rolling diameter it is exactly what the manufacturer has recommended. Put it on a website and percentage change is 0.23% and circumstance change is 1.5mm. still juddering. I have Michelin on front and Bridgestone on the back could this be the issue?

@@OulyHussain Yeah tires vary greatly from what they say on the side. watch this czcams.com/video/P_vuyNeYOlo/video.html You need to actually measure your tires against each other. MRT

I bought the copper or metal one . Do i need to replace with one u used here ? Plastic and rubber material ??

I would need more information to help you. Is the tap leaking from the shaft of the tap? Or dripping from the faucet? Did you change both washers? ie did you change the wrong one? The washer seats against the metal at the back of the tap you would need to check if that is still Flat or if there is debris in there. Did the oring move out of place as you fitted it??

Thanks for the Comment. So lets see you do this to your Bike???

Yes get one of these hose link adaptors. ebay.us/cElilV

@@Marksreviewsandtutorials thankyou! For your reply.

No this leak won't cause smoking. Have a look at these videos to help you out. czcams.com/video/1NzTAGb31WI/video.html

Thank you so much. I have a BMW x1 2011 and I just suddenly started smoking after the car was serviced for the first time and the tappet cover seal was changed as well. I just want to know what questions I should be asking the mechanic to ensure everything is fixed. Also knowing what to look out for. The smoke appears blue sometimes and white sometimes. I also noticed I put in some coolant and when I checked the next day the valve was low. Is that normal?

@@chariitywrites If you had the tappet cover gasket replaced and the car has begun smoking you should tell him that and ask if the PCV valve was checked/cleaned and has been re installed correctly. The coolant level shouldn't be changing

@@Marksreviewsandtutorials there is no visible coolant leak, or any leak for the matter. What could be causing this? I’ve done a lot of searching and I’m scared to say head gasket failure. But do you think this is the case? And if so what will it take for this to be repaired? Is my car going to be okey🥹

Yes. Links to buy and the part number are in the description of this video. MRT

Glad it helped! Thanks

Just water

Yes I considered that option but wanted to retain some buffer to roughness on trails and roads I cycle on. I was happy with the mix of AL and Carbon (forks, stems, wheels, brakes) that Grail 6 model offered. At the end of the day, we choose a bike to suit us and the terrain we cycle on hey? Enjoy and happy new bike day when it arrives. You won't be disappointed