Video

Who ,akes that tool that he is using to drive the bearing in?

I’m so glad I found this video. It’s the only one I’ve found of me racing. I was the yellow 11 car. Unfortunately I broke a right front ball joint in the race and had to pull off. I wasn’t very good but great memories

Where did u get the puller bud ?

Cant find any info on this dirt track, do you know what happened to it? Are there any left in Arizona?

Like your quick to the point video, having to do the same on 2000 blazer, glad to see you put wheel bearing grease to lube the bearing another video use lucas, but wheel bearing grease is the way.

Does the gear oil lubricate that bearing too? I’m not a mechanic.

How can I tell it`s a 7.5" or 7.625 inch? I have this 1999 pontiac firebird trans am v8 convertible. I had some differential issues and ordered bearings for 7.6". Problems! I think it`s 7.5" . What is the difference and where can I find the right number 7.5" or 7.6"...?

Great video! Easy job but I came here to confirm how deep the seal should end up (looks about 1/8” past flush)

Dude say something tell me which way the bearing supposed to go in that's what I'm looking for because it does matter and you're just sitting here quiet as mouse

Thank you sir I've got a bearing on one at work that's being a whore

Does anyone know where you can get that tool to put the new bearing in?

I don't think people in that part of the country know how good their racing is, look at the empty bleachers js

💚💛🧡❤💓💗💖💝💘💙💜🖤

If that's bad will it make a loud thump noise

Is That A G20 Van ?

Thank you for the video

Straight to the point, great video.

Can't get any easier than that, simple and direct without a word said . nice job thank you

Do not do that with your axle shaft the bearing puller will slide through the seal if you can pop them both out at once

That was a great race I thought the 2 car was going to win the way he come from mid pack getting into that outer groove and rocketing to the front

Wow! Great racing! Awesome, skilled drivers!

I see money going out your door bro let's go green and black let's go

Jerry stop focusing on that car

Are camaros allowed to race in this class??? The rules are a bit hard to figure out..

Is that the former Tyler Smith car? AKA former Mark Schuneman (spelling) car? formerly 8x

Good video thank you I needed my memory refreshed

I'm wrong it's not spring should be twards the oil my car was installed wrong from the factory

Seal is in backwards!

on a follow the leader track, where all the leader does is block, what did people think would happen.

thanks

Nice video! Thanks for posting!!!!

Fantastic fucking video. Short, simple, right to it. Just what I was looking for.

Helpful Post, Looks good www.premierwestgears.com

Thank you Jerry

Real helpful, much appreciated.

what bearings did you use BC for whatever reason...I can't seem to find any for my 87 cutlass..7.5

thanks man this was helpful to me in houston tx

merced speeay 10000000000000

You left out the part where you have to buy a kit to extract the broken retaining screw in the differential cross shaft before you can pull the C-clip and pull the axle. Nice video of the last steps. Doing it right with proper driving tools.

Loved going to that track even though its 2 hours from home

What's the exact name of the tools you were using? (Drive tool and puller)

What tool are you using to pull the bearing...it was so quick. We've tried several brands of bearing pullers for our 1970 Chevelle and none work.

wy dad is # 79 with the pink duck tape numbers

great video. thanks!!!!

Howdy, I really like your video. Have you considered making some more of these videos? Hope to see more videos from you soon. Russ

Nice one. Why you throw a caution when no cars were even stopped on the track. Besides the 2 car should not have sweezed John in the the counter. He had him beat into the corner.

Great Racing !! J.W.