Video

If you have a mouse, they have found a way inside your house. Areas beneath sinks are prime infestation areas. The electrical box outside the house is a prime area to inspect. So are bushy areas close to your home. Look for mice turds inside and set traps where the turds are found. NOTE: the go-to material for sealing holes inside/outside of your home is that same spray-plastic that pocket windows are sealed into homes with. it hardens up and makes the hole disappear.

On the yellow plastic plate there is a F (firm) and an S (sensitive) setting to place the trip rod. My pest control guy says to push the bait into the little molded yellow box, just above the trip rod. I've got two mice so far.

If only it was obvious there was a firm and sensitive side.

2024 boys. We are living in the future!

Only Jerry can escape this

A mice enter my apt, this one is smart avoids this traps and eats the bait

Anyone else came here after The Big Bang Theory

Mice cannot resist peanut butter….even more than cheese

My dad set one up along the counter wall then at 3am he caught the jerry sucker

I’m a mechanic of 35 years. These pieces of shit don’t stay set for nothing. One out of the pack works. Trash. Don’t waste your money. Snapped my finger twice. Got one set, few min later I hear it snap off by itself. Junk.

Super easy, I tried the cheapest one and found them incredibly difficult to set

Those toothpick / q-tips suspiciously look like fingers and hands 🤔

I bought a pack of D'con no touch/no see traps. They have been out for a week. The mouse wouldn't touch them. I set out this old style, and within 30 minutes, i caught him. They are a bit touchy, though.

JT Mechanical inc. My customer like this really easy and fast setup. I have setup a few of these now and got nothing but good reviews. I like this product and I will be using it a whole lot more. We or located in California where we have very strict watering days. This helps out all of my elderly folks I work for. Thanks again to whoever put this kit together.👍

We have a friskers P552 small pruner / clipper abd they don't open unless you. Pull them open with two hands

Thanks for leaving out to set the starting point for all the subsequent adjustments! How do you set the right side stop/beginning rotation position? A real world outdoor video would be a major improvement in the presentation.

What he said is distance adjustment is really the retaining screw on the nozzle. I turned counter clockwise and blew out the nozzle.

Glory hole

I won’t lie I snapped the fuck out of my fingers figuring it out watched this and I was done thank you.

Plan is snoopy and Camp Snoopy now open at Kings Island Park

the solionoid needs to be extended to stop the flow of water. So im confused why you say it needs to be retracted.

Qui c'est pas fait coincer les doigts avec ce piège a doigts !!!!!!!!

It was terrible. Big hunks of ice came shooting out of it and we couldn't have loved it more. 🧊

I have purchased 3 that are a pos at least I know to stay away from these

Easy to set...... yeah, sure. 😮‍💨

The jaw pads are its weakness. They get crumbly and break apart over time. But there is a man on Etsy who sells replacement jaw pads he created with his son. They’re far better than the originals and look like they’re built to last.

Saw a mouse yesterday so went out and bought two of these. Within a couple of hours I caught one. These things are awesome!

How to use the bleed screw?

I caught 4 mice in 2 days using these snap traps, which were invented in the 19th century I believe. You really can't improve much on a good initial design.

God, damn it! I didn't know there were different setting in this trap. My mice have been walking away with bait!

Did not actually show how the valve works....

I honestly wish you would’ve showed how to use the shredding blade because I’ve got this unit and I haven’t figured it out. I can’t close the top because the blade is up on the top.

Is this the same too used with Hunter rotors? Thanks

Need new cord on my RK5102K

I SMASHED MY FINGER OWWWWWW

Thanks that helped

Really hard to get the Arm bar over the Kill bar, the Arm bar is very Short and it does not stay under the Kill bar - tried several times and couple of close calls :) If anyone has advice on this part, or if there is a Video that shows how to SLOWLY show this Critical part would much appreciate !

I can't get mine open, either. This video is a waste of time and it's looking like Fiskar's pruners are a waste of money.

Man this thing is INCREDIBLY sensitive. I only managed to place 1 on the ground without it triggering. The moment it touches the ground, it triggers. I literally cannot be gentle enough

Wow lol all you guys are bitchers 😂

Yup had fun with this great toy this brings back so many great memories ❤😊

Mango Caterpillar

These never worked because you needed a curved piece of ice to sit against the round metal shaver

I caught one just now with this haha, them sticky traps kinda suck lol

Its a sign of the times i had to watch a CZcams video as i couldn't get the traps to set from the instructions on the back. Im 61 and am so thankful for CZcams! 😊😊

One pointer is use gloves to ensure your scent isn't on it*

Firm/sensitive side? Well, that's new.

Hasbro til all are 1

Jesus saves

Victor mouse traps is good for big mouse,but not for small ones.