Video

First time doing anything DIY and this worked! Thanks so much

From IFixIt: Note: If there is a thin plastic film on your replacement battery, do not attempt to remove it. It is glued on and protects the battery pack while it is inside the MacBook.

Nice but you might wanna cut off half an inch with the pipe insulation

Great video

I wonder if some kind of glue could work instead of tape. I don't do well with tape.

Would you have the link or files for the spacers for the alice frame. Great video by the way, very helpful.

THIS is the video ive been looking for. i dont have the money or time to build a spreader, but i have 10 of these clamps. hopefully they'll provide enough force to spread the metal frame stiffeners fpr my solid axle swap project. i did this with some of my long bar spresders but theyre too flimsy, theyre for wood after all. i hadnt thought about this though.

will try it - yep the computer repair guy wanted 250 for it -

I’m gonna try something like this. I saw the witches and want them but I despise battery powered and want either electric or solar so im going to have to steal this as a base I think

I love this easy to follow video! I just changed my battery today and voila-my laptop came back on without any problems! Thank you so much, your DIY on how to install a new battery saved me a ton of bucks! Forever grateful!❤🎉😊

Is it ok to do this if battery is already swollen?

I used this video to make a smaller version of this. Not too hard, looks good

I love this idea! I do think for the body I will use chicken wire though! I was looking for an idea to waterproof the head and the milk jug is perfect!

I got a fairly new roomba that I think got compromised due to running over a toothpick/chopstick and after troubleshooting everything decided to get a new cleaning head as a last resort. I would not have been able to replace it without this video. I sincerely can’t thank you enough for saving me having to buy a THIRD ROOMBA! 👏🥳

Can you tell me about the long-term experience with this battery? I have read from so many people, that these batteries don't last very long and often suddenly shut down when still on 40% or something like that. Do you now something about this? Great video btw!:) Thank you!

I had to laugh when you went to plug it in.😂

so very grateful!!! took me all of ten minutes or less!!! $48! saved me a 3 hour round trip and about $150 to the apple store!! hopefully I get another 2 years out of this MacBook Air!! used the link provided.

Float switch has a thermistor in it for measuring proper temp

Doing mine back to 1984 simple pack and I'm 53

If I spray bleach on the fan blades will the smell start going inside the house?

hello

Good video. Informative.

Very cool! Did you ever end up making the accessories? We're looking at making a table for Dungeons and Dragons soon so doing as much table research as possible for what we're wanting!

Great video. What set up do you use to film the installation?

Who here needs a video of replacing this with the exact same style ???? A fucking toddler could figure this out. I need to replace this with a new style lock. God forbid youtube or Google shows me something I'm actually looking for.... fucking frustrating. If you need a video on how to replace this with the same fucking style lock and knob, you definitely live in the suburburbs yuppie fucks.

Went through all of this and still get the error. Guess I have to call support

I ended useing make it or break it's idea on his wand upgrade by adding a momentary toggle switch to the pack instead of adding it to the wands hose and then used the hazlab wand where they both work independently from each other for a switch me on effect.

13:12 Those aren't the cannons, they're radar dishes.

the music really ruins this video

Great video. Thanks! I’m gonna replace mine today. It hasn’t been working for a long time.

Thanks for this video. Had wanted to see how this stuff turns out.

Super! Roomba is the best! With love from Moscow.😀

Does doing this hot method also make weeds less likely to come back? I am sure we all get weeds once in a while.

This stuff does not work for more than 1 year. It tends to stick to one side of the crack and breaks free during freeze thaw movement.

did you end up using supports when printing the dome? Or can the build support itself. If so regular supports or trees?

This video cracks me up!

I was watching another video about calibrating the power management system and it saod to charge to full and leave it plugged in fkr an extra 2 hours. After that run it until its completely dead and then charge it up full. Does that work as well?

Yep. I had this problem. Thank you so much for tip to not use a powerdrill. I heard you say that right when I was powerdrilling away. 😂 You saved me a headache. Very simple directions. Great video work. I couldn't find the screws until you pointed them out. Thank you so much for posting.

I also painted the cilindrical part with the warning sticker silver as well. Maybe a few other small changes, including the Alice frame were also done. I got my neutrona wand before they put the ones out with the orange tip.

I switched the molded wires on the 'damaged' part of the hose by cutting the mold off, and stuck real ones in. I took the cable sock off, and bought the type used in the movie. I painted the under wire. I painted the wire parts of the cyclotron using paused screen shots. The rest I left as is.

"Thank you, geniuses!" 😂😂😂 Once I was through laughing I started the video back up and was successful in changing out the battery! Thank you so much. The internet rules.

Thank you!

Thanks for the video. Quick question: You mentioned that the water was above the floater level, do you know why it did not flood your basement when your original pump died? Got lucky or is there another reason?

LOL this should have been a 5 minute video at most....but it seems you get more money from CZcams if your video is ten minutes so these people drag this videos on pretty much giving your their life stories! ....WTF? After you filmed this did you even watch it before posting it? Your camera was way off center....you didn't notice this?

I thank you.. I've put off the thought of fixing mine! it was on life support until the battery display said 0% and eventually, nothing. Now i can bring it back to life .. resurrection!!

It shrinks, so you want to do multiple layers, making sure each layer cures before the next application. Also, adding and mixing some sand in between minimizes the shrinkage. Filling wide and deep cracks all at once could cause bigger shrinkage and craks as a result.

Hey AP! Loved this series, and I am trying to make my own right now! I've printed the pieces from another source, but would like to use Baddeley's automation instructions. I subscribed to his patreon but I seem to be unable to find any BD-1 files. Would you happen to know how to access them?

What Crap Video U don't show what you are looking at after pluging it in. And you talk too much. Just dot. Boss

I would say with a crack that. Wide, you needed to use cold patch filler. But you'll probably be okay. :)

There are five screws inside fyi! otherwise the video helped me to replace the battery..