Video

Great job! A bit scary but really cool!

beautiful

couldyou tell me where you sourced your branding iron. Thanks

Beautiful

Beautiful

Clever and unique!!

Oh, I thought the outer panels would be more spherical, so the flask could hold more liquid. Nice technique by the way. And for the record, ALL two part epoxies are food safe once fully cured. Another way to make it waterproof is to simply glue the panels on with epoxy, then when cured, melt some beeswax and pour it in. Fill it right up and dump it out immediately. That will leave a nice coating of wax on the inside.

Hi. Great work. What oil are you treating the finished wood with to get that shine? Thanks

Inspiring! Thanks

Very creative and beautiful.

Sure would have bin a better vid if you talked there sir 🤔

Very nice and creative indeed. New subscriber.

Outstanding video. I'm going to try to make one

Классная работа!!!

Hi🥰🥰I'm Kelsey from BASE CAMP😆. I hope you are all well! Would you be interested in testing a mask from the second-largest mask manufacturer in the United States and sharing it with your fans through a reel post? We specialize in designing and producing comfortable, lightweight, and breathable dust masks since 2015. As the second largest dust mask manufacturer in the United States, Our masks are mainly for woodworking, construction, and agriculture. So far, we have attracted more than a million users who love our products.

Классная работа!!!!

Why use glue if you can make it out of a single piece of wood?

Andrew Hall used to demo this in UK. They are nice, well done.

OK, how many handles am I going to break? lol

Grelt design - what are the angles? Can you share your drawing as pdf?

Is it going to be a cheese platter?

Lovely share. Most of us do and did suffer from the same bowl (etc) gouge's sharpening issues. It is really time to to get a proper wet stone sharpener even if just using to sharpen those finger nail ,bowl,spindle gouge shaped tools . Couple of times my mood was off when I could not find the right angle to sharpen my fingernail gouge on a standard grinder 😢 As a full time joiner, I always wanted to learn those sharpening technics ,which you can only practice if you get a proper grinder. Thanks for sharing!

The other way I've seen the drilling done is to put the jacobs chuck into the headstock. put a live center in the tailstock, and pinch the work between the drill bit and the tailstock. start the lathe (hold the work piece with one hand), and advance the tailstock to drive the work piece onto the spinning drill bit.

Ciao Nordico, sarebbe bene conoscere il tuo nome per amore della condivisione, ho apprezzato molto il tuo lavoro semplice lineare e pratico, Anch'io utilizzo il tornio e davanti a questi piccoli pratici lavori eseguiti da persone esperte come te, mi ritengo sempre un principiante. Complimenti amico mio. Un italiano di Roma

How did you get it centered for the second axis turning?

Love it.

No resin is food safe. By adding it to your project, you've ruined it for use as intended. Sorry, but wanting something to be true doesn't just make it true.

Nice work. Beautyful because of the simplicity. I enjoy watching the video! Keep on turning.

Thanks 👍 I use a Tormek T8 with all the jigs I need and it has given me consistent results. It cost a bit more than others but well worth it.

I don't know exactly what you made this little wooden box for, but I know it's very interesting and neat for your work.😊

أتمنى أن أحصل مثل هذه الآلة 😢

That’s really cool, and the spoon turned out beautiful

👏🏻👏🏻👏🏻

Start the hole with a short drill bit to give you a straight start, the long drill will be held true and continue.... Thank you Shawnhaywood.

Very cool

I went through similar journey bu in the middle i was using the Tormek knockoff from Record Power. Apart from all the stuff you mention the issue i had was constantly adjust all the jigs to accomodate for the wheel wear. I eventually settled on Robert Sorby Pro Edge i extremely happy with it and i havent looked back since.

I bought the Jet knock-off version of the Tormek - same issues. The stone is out of round and the bowl gouge jig is not as accurate and setup instructions are missing.

For bench grinders there are plenty of jigs for bowl gouges (oneway wolverine system, kodiak system) - there is also the sorry sanding system. Did you look at any of these?

About 900 for just the Tormek t-8 Black, here in Norway. Sometimes the investment is worth it. Considering the amount you save long term.

Very nice. Good thing you added the light colored wood!

Great tutorial. I will looking for something challenging to try. This can be my next turn. Thank you for sharing 😊

Impressive work

I love this bowl…it looks like an acorn!

Beautiful thing and od course, I am curious of Your sharpenning style.

Very nice. Great information on wood chuck jaws thanks

Thank you for this detailed video. That record power looks strikingly similar to my rikon 220

Well done 🎉

If you dont have cole jaws a disk of wood atatched to face plate can be used with hot glue , wood glue or even double faced outdoor carpet tape to hold I wpuld have mounted the base in chuck with yhe lid on tail stock end and use a block between the live center , to have more stand off room to finish the lid Overall a lovely box A simple rotary punch for holes in leather can be bought at most ctaft supply and building supply centers for under $ 20.00 USD What brand face shield do you use ?

I believe your right, the wood looks like elm. I work in a park during the summer, and we have a lot of elms. I would like to know how to sharpen my chisels properly. Thanks.

Smart