Video

Hey there! Great video! I had a question on using the lamello to create the connection closest to the outside edge of the miter for a tighter outside miter since that’s what will mainly be seen. Am I overthinking it or do you think it would make a difference. I’m making a waterfall walnut table that is about 2 inches thick

Why do I see multiple comments and replies stating that the voltage is wrong? Protrade is a UK retailer, Mafell are German and around 80% of the world use 220-240V. If this is available in the US then it would be a 110V variant, if it's not, then you're probably dealing with a non official authorised seller.

I dont think the cost justifies the 9 seconds though

У меня такой

Is this no longer made? I can't find it on the site you linked to.

When and where in the USA???

Thorough

Not bad. But it needs a pocket or a belt clip

Yeh absolutely pointless video. The full strength of the other products is reached over. 24hour period. That is when u need to test the strength of each adhesive once all have reached stated total cure time. Very biased for sumogrip superfast which kinda says what it does on the side of the tin or tube so to speak lol. Shame I would really like to know the real end result for this test

Das ist doch 100% das gleiche Video wie beim Metabo Fan!?

That is not the Phenolic jig shown in video ?

A link to supplier would be handy.👍

what just happened to my ears

What a pointless experiment

Video sponsored by sumo I'm guessing 😅. Absolutely no way did CT1 fare that badly. I've stuck a huge piece of stone back on that I accidentally cracked off due to rushing. It was fighting gravity from the off and 5 years later its still on. Not having this video AT ALL

I have this head torch. As an electrician i usually need to wear a head torch for long periods and most head torches with batteries at the front cause head aches and i find the split system type with the battery housing at the back to be awkward when wearing a hat (beanie or trapper hat) in the winter. This head torch doesn't cause headaches after long periods of use for the simple reason that the rechargeable battery is absolutely RUBBISH. I switch through the dimmable settings to find the lowest one. On the highest setting you can get roughly 1 to 1½ hours and when the low battery warning light glows red then the moment you turn it off for any reason it will not switch back on until you recharge it.

Might open easily brand new, real pain in the ass after that. Came close to breaking it and tossing it in the dumpster.

Metabo 4000 rpm beast!

I just can’t justify £600 for something I could barely fit 4 tool boxes in. The drawers would be more value than what’s inside ffs 😂

WTH

does the lady come with it

Hello, can the hikoki 18v batteries be connected to the vacuum cleaner?

Под столом бы ещё собирал .

Nice Swiss Air! :)

I use these every day and they are impossibly heavy and difficult to use. The pipe is very rigid and fights you all the time when trying move around your work/bench. If you enjoy repetitive strain then this is the torch for you...

hahaha maybe you should redo this test with a fresh drill bit. That drill bit took its own sweet time to get through that bit of metal.

Question for Milwaukee specialists: My Milwaukee Sawzall M18CSX has the following error: The LED lights up 4 times and the motor just jerks and returns to the starting position. If I then move the turbine a little, it only works for one second and stops. After that, the LEDs light up 6 times. While the LED lights up 6 times, I can saw in an emergency, but I have to press the trigger every second. I checked the MOSFETs and all 6 are correct. It seems that the signal is missing or the hall sensor is faulty? What is your fault diagnosis? Greetings from Switzerlan

Very poor video. Very few close up shots to show detail. Who on earth chose the camera position ???

The fifth cut should be done over the first cut not the fouth one. Your demo is wrong on this point and prooves nothing. Too bad that you do not show us the diagonal length, we have to believe you. The only "acceptable" proof might be the digital square if it's really working well. The square seems to be of good quality otherwise.

Please allow us to have doubts about what we have seen. You need to let the 20 minutes pass by keeping the camera on, facing the wall. You can always edit the video and speed up the drying time, but it needs to be on camera. Also, half of the first line of the Stixall was left at the top of the brick.

Donde puedo hacer la compra

This was extremely helpful! Very easy step by step instructions. PSA… the screws are very short and out of excitement can fly off the screw driver.

What about balancing on 2x4 beams in attics

I mainly do solid timber and will mainly use normal biscuits, my dealer sold me a zeta p2 which I’ve realised now I need another ( expensive) blade for. Would you recommend changing machine to classic x or should I just get another blade and the zeta can then be used for everything lamello offers ( I think) Or will it be bad for the machine using it mainly as a ‘sub function’ ie normal biscuits? Sorry if this is a noob question 👍🏻

That’s great, but I would sooner watch how it works than to learn how to put it in its case. 😂😂

promo sm

Pointless test that tells nothing about strength of the product , the only thing it shows is who dries quicker .

Feeling like a total baller after getting it on Monocashback for only $40. And with a 50% discount and an extra $2 in cashback, it's a no-brainer. Monocashback, you're my hero!

Hi, these power washers are very good. I am happy with a similar Nilfisk power washer E 140.3. I bought a used one (broken) and did fix it. Easy. I have even recorded a video tutorial about it. I think it might be helpful to your viewers. Good luck. czcams.com/play/PL59Co9iveKeo2B4wvzHleZdYWYqd1OOtF.html

Thats neat. How much re they please?

Which is small one

Don't think it is never seen it or heard of it

we have yet to discover the functionality of the preloading clip

Svp réglages opssion taking of tig

Wish they sold black here in US

World's first? Nope. Shopsmith made one in the US in the early 90s. Shopsmith 2000.

This is so fake we was fixing facade panels on stixall and all super heavy stone panels, this is only advert

great ! please , more table ToughBuilt !

Alan, great product and video! I am in the USA, how do I get one?

A very useful video.