Video

No voice, no music, straight to the point, well filmed. LIKE (y)

prima video!

What floormat in your trunk do you have there? Like it!

I’ve got one, when I remove it I can’t work out how to get the key out of the tow hitch, nothing seems to want to turn, the handle is stuck in the out position. I can remove it when the hitch is installed. Any clues? And yes, this is the only video I’ve found on CZcams of the euro tow hitch!

Does the price include the 13-pin wiring? In the UK there are two prices (£1090 and £1200), and I can't see what the difference is.

Hello, thanks. is this a tesla which ordered with option of Tow Hitch at the beginning? Or Tow Hitch is not ordered at the beginning, but we can install it by myself ?

😕 🅿🆁🅾🅼🅾🆂🅼

American version: czcams.com/video/Di_Q_CTbj3o/video.html

"Pikkuisen" myöhäinen kommentti, mutta eikös tuo nyt ole Bella Falcon 26:n kopio...? Ei millään pahalla ajateltuna, tuli vaan mieleen heti kun näin....

Why'd you replace the LDO? Is it safe to run these directly off 4s battery?

I have this exact problem but when I solder to the pads I get no tone at all?? have tried both ways and used multiple buzzers, any ideas?

I had the same issue thanks for the video. This fixed it right up... Aliexpress strikes again..

Thank You!!! You resolved my problem!!!

Just got a few clones from Aliexpress : same fucking problem. Thanks a lot for that video !

Thank you!! This is what I got too - clone board buzzer connector incorrectly polarized which led to constant beep after plugging in, ignored connector and soldered to pads under board, works perfectly! Thanks again

Thank you! Got same problem Bought mine at aliexpress/ RC Hobby Market

Thanks for the solution i have this problem to.

Thanks for the video. Wires were backwards on my buzzer, flipped them and then I get constant tone. Then google brings me right to you. Well done

Yep. I just found out this was an issue. Thought I had first connected the buzzer wrong. Thanks for the video..

So here's what's wrong with the socket, the processor normally switches the ground and the socket is straight to the ground circuit. It should go through the switch as the solder points do. Pure F***% genius (NOT).

Check mine and its the same. The piezo is left floating so it just squeals. Did anyone buy theirs from HK??

thanks man ,i don't realize until i saw your video

Thanks got the same problem after connector was broken, now I use the underneath buzzer solder pads on this clone.

Thank you for the tip to connect the pads directly. It worked for my (good)luck clone. Happy FPVing !

Just solder buzzer to the pads. Forget about the connector

hobbyking sold one of these. I connect buzzer and no sound. Then reversed wires and cot continuous alarm. Then discovered same thing...

How to fix it?

I had the same issue with the clone with sockets. I then purchased 2 original ones from GetFPV and they work as advertised. It makes one wonder what else is done incorrectly.

thanx man, have the same problem

Hy, Sorry, but I dont understand it ?? What have you done with the Cable from the Buzzer ?

I bought the copy intentionally. It's less than half the price. I figured out that it is only the buzzer socket negative that is connected to wrong ground. Buzzer works now fine when connecting it to the pads beneath the socket. Of course I feel bad for not supporting the community monetarily but I try to help otherwise.

The board is not an SPRacingF3 original board. It is a fake China copy. Not suprising you're getting issues. If you want support then buy the original boards please. Official retailers can be found here: seriouslypro.com/retailers

hello. someone told me.. it's better use ECC Memory when i'm going to use more than 64GB ... in the other case use a normal memory.. Jan it's really true that ? thx for the answer :)