Video

Jesus, I want it so badly to move your camera so I can see what you're doing. Unfortunately, I didn't learn anything.

Hai sir I have Polaris atv 250 two stoke engine bike esterday what happen I am going to change a battery . Wrongly connected but engine start after rectifyeris burning i going to stop the engine.afer we are going to connect the correct way but self moter sound only coming.but wrong connect self moter start engine also start but correct way to connect is not working.what i going to to please give good solution

Hai sir I have Polaris atv 250 two stoke engine bike esterday what happen I am going to change a battery . Wrongly connected but engine start after rectifyeris burning i going to stop the engine.afer we are going to connect the correct way but self moter sound only coming.but wrong connect self moter start engine also start but correct way to connect is not working.what i going to to please give good solution

Do you still have that 400sbc

I can’t see s%%*

Them rear tires are on backwards they’re directional tires

I have a 330 trail Boss Polaris someone unhooked some of the wires in the front of it and I can't for the life of me figure out where in the crap they go a lot of them are hot someone please help I like the diagram up online they are too blurry to see or read when you enlarge it

I have a 2002 400ex atv is not getting grounded properly what should I do and can y help

Is the float suppose to sit like that?

Aim the camera please

Buenas tarde ando buscando los piñones de arranque de la cuatrimoto suzuki vinson alguien me puede ayudar por favor gracias

That man does it write! Shrink wrap them wires no tape! Lmao i see it so much! Its ok to bragg when your doing it write buddy!

The fuse box should be close to the solenoid...20/30 amp?

Looks good. Only thing I would do different is on the first fire give it about 1/3 throttle and hold. That way you can set the rings.

thanks ! I was having trouble with that gray wire it was broken an it did not look right it broke from the red wire don't figer

Check your pressure on your fuel pump and spark voltage. It’s turning over so that is a plus. So all that is left is fuel & spark !

Sometimes it’s not the ECM but the plug&play connections. They vibrate and create arching especially on the power in and ground. Ground is the first to check. The mounting screws, threaded into the frame are to fine and loose contact over time do to vibration. Hence the front motor mount failing do to the same issue (vibration). Before sending the module out for repair or replacing with new check those contacts and the ground continuity. Also as an add of prevention use dielectric grease on the female contacts on each side of the module. The other, but not as critical is the location of the ECM, is the heat discharge from the radiator and the fan blowing excess heat directly onto the back of the ECM.

Thank You, Great Job !

I have an 02 vinson yellow. I wanna put bigger tires on it and I know the clutch won't handle it very well. Can the secondary clutch be clocked like a cvtech? And which weights should I replace the stock with? Any help would be greatly appreciated.

Hey man I know this is a older video but what wires from the bar harness got the solenoid doing a new harness on mine, thanks

That was helpful just got a 400 with no sol. and wires hanging didnt know where the wires went now I do Thanks again

Wish you had more light or I had better eyesight lolol I’ve overhauled Cummins old DD and about every auto engine and small engines but not atv yet but will soon and it is this engine Thank You for Video

What was the torque on the rocker box bolts??? 😊 Hope you’ll answer Thanks

its almost a 180 degree bend

I cant even believe someone hasn't pointed out the GLARING ISSUE HERE um dude you have the rollers literally set to crush the tube move them all the way to the out side there isn't even enough space for the tube sitting in the die to make it past the rollers with out crushing due to mechanical force

bayou head bolls have a straight shot in

How is the piston holding up? Thanks for the info

Spoke too soon you're on it.

One of the throttle cable nuts goes under that black cap!

Great video I appreciate your help a whole lot

On the float there's a little rubber o-ring that goes in the carburetor not the needle did you snap that in mind won't fit all the way in and I'm having an issue in about half throttle it starts breaking up if you could respond and maybe help me out man I'd appreciate it thank you

How are the numara piston and gaskets holding up?

Shifter isn't reading neutral is why button ain't working

link for the bender

Now my dogs are barking 🤣. I'm still having no luck with this electric system.

I like your video.. can you link to the product?

What size jets at you using

Now you have 10x the subscribers! Good job!

Excelente video, gracias

Well done brother!

LMAO I love when people buy those "cheap chinese, so called carburetors" and either use them or start swapping parts from them onto the OEM carb, and then wonder why the bike won't run right. Or think the bike is running right, when in reality it isn't. I've been working on bikes for years, and have NEVER replaced a carb, I ALWAYS rebuild them!!

🤷 ≋p≋r≋o≋m≋o≋s≋m

Great demonstration on how to spin a wratchet

Would like to see about how to adjust that carb!

First comment 🤘

Yep you definitely have enough plastic off to get to the carburetor 😂

Every time I try to watch this video all I get is a spiral turning and turning and turning it no never let me watch the video what is wrong with this video that you can't watch it it's like a spinning clock in the middle of the frame it don't even play it don't matter if I reset my computer reset my phone it's like that all the time what is wrong with this video

I just finished watching this good stuff. I have a Lakota with a cheapo Chinese carb on it. When I’m at half to full throttle the quad breaks up. Why?

Hey how you been long time no talk you move to the city

my vinson 500 can wheelie thats how much power