![ATRGUIDE](/img/default-banner.jpg)
- 74
- 77 241
ATRGUIDE
United States
Registrace 7. 09. 2021
We are buiding a library on automotive electrical systems, we want to teach the electrical side of the automotive industry. Automotive industry is getting more and more complicated, we are trying to teach a differant way on diagnosing the engine, transmission, video monitors, abs, perty mush anything that has to do with electric. Learn how to read schmatics and trace out any electrical problem. Think about it if you learn this way you can understand any elctrical no matter what it is on, car, house, it doesn't matter. We are showing where to hook up and what the pattern should look like, known good data, known good data for the scanner, hopefully we can build a association with the automotive industry to bring everyone togeather to help each other through the video's.
Learn how to get the most out of your Zeus Scanner an effortless way to figure out a short in a fuse
Technicians must fully utilize their tools. This video will demonstrate how to analyze a fuse that is shorted out when cranking the engine. I will also show you how to use ohms with the graphing meter, which has many applications on fuses, injectors, or anything else that may require resistance. Hopefully, you will understand what I am doing and use it for whatever you want to execute it.
zhlédnutí: 75
Video
Hyundai window module not working how to test the window switch and window motor
zhlédnutí 62Před 2 měsíci
Before you buy replacement parts, watch this video to learn how to test the window switch or window regulator module. By following the instructions in the video, you can save time and money.
Mini Cooper fuel pump relay not working, replace fuel pump relay in internal power junction box
zhlédnutí 996Před 3 měsíci
I can help you learn how to avoid replacing your power junction box when it has a non-serviceable relay. Instead, I can guide you on how to install an external, serviceable relay outside the junction box. This will save you money as you won't have to buy a relay kit and install it.
How to test your side view mirror with a ohm meter, Explains how your mirror works electronicaly.
zhlédnutí 109Před 5 měsíci
This will show you how your side-view mirror works electronically. This is the way you don't have to replace unnecessary parts on your vehicle. Test each wire seperate with resistance. Easiest way of testing a mirror switch
Can Bus Diagnostic on a u code finding an easier way to diagnose a u code or a shorted out computer
zhlédnutí 177Před 5 měsíci
This is a easy way to test a can network system on a auto, I will show you how to use a scope to diagnose. This will knock off hours of diagnostics on the u code or a computer that is not communicating with the scanner. Look how to take advantage of splice connector and what they are used for.
How to program a ABS when you don't see the asbuilt data, how to trick the software to program.
zhlédnutí 178Před 5 měsíci
This will show you how to program a abs module through asbuilt data when there is not a icon to click on for asbuilt. This will teach you how you can trick the programmer to where it does'nt know what vehicle is in it. If you want to start to learn on how to program go to atrguide.com and see what equipment you will need and we will teach you how to program
B2199-16 Battery Voltage below threshold, air conditioner not cooling the car down inside
zhlédnutí 375Před 6 měsíci
B2199 Battery voltage - circuit voltage below threshold In this video, I will guide you through the process of diagnosing a compressor that has a solenoid built into it, known as suchan solenoid. This issue is quite prevalent in Chrysler and Dodge Ram vehicles. However, it's worth mentioning that several manufacturers incorporate a similar system, so the information in this video should be usef...
p00FD aux battery, or diesel with 2 batteries, code p00FD in the system
zhlédnutí 113Před 6 měsíci
By conducting individual tests on both batteries, you can diagnose a p00FD code that signifies an auto stop code. In this informative video, I will provide step-by-step instructions on how to test each battery separately. Additionally, I will explain the process of conducting a load test on the battery. Understanding these procedures is crucial since the occurrence of an auto stop battery b cod...
BMW convertible not working how you can see the most common problem
zhlédnutí 44Před 7 měsíci
This is how a convertible top works, so you can diagnose it properly. I'll try to simplify it so you can focus on specific points and check to see if they work. I will give you the most common repairs and explain the process of how it works, providing a step-by-step diagnostic explanation.
TPMS Programing Chysler product. How to program using a tpms tool and a scanner to the tipm.
zhlédnutí 25Před rokem
Here is a detailed step-by-step guide on manually programming a TPMS sensor when your tool fails to do so. Follow these instructions to input the hexadecimal number into your TIPM (Totally Integrated Power Module). In certain situations, more than relying on a TPMS tool is required, regardless of your tool type. By following these additional steps, you can ensure successful TPMS sensor programm...
How to program a Ford door module using asbuilt data, where to locate asbuilt and install the data.
zhlédnutí 339Před rokem
Sometimes, when encountering a module that lacks communication capabilities, you may need to manually input the coding number. This function can be utilized on most Ford vehicles to program various modules. Ford has simplified the coding process to ensure seamless integration between modules. Explore an alternative approach to programming that opens up new possibilities.
Honda/Acura PCM Replacement, how to replace your pcm with a used ecm on your honda or acura
zhlédnutí 1,8KPřed rokem
I will show you how you can replace your pcm on your Honda or Acura, shows how you set your immobilizer or how to program a key. You don't need to buy a new pcm, save money and reset your used pcm.
P0315, Ford Crankshaft Relearn, Where to go when you can't find how to reset a crankshaft sensor
zhlédnutí 9KPřed rokem
????A CRANK SENSOR CODEHELPWHAT TO DO WHERE TO GOIS THERE A FUNCTION TO RESET P0315What do I do KNOW P0315 How can I get this code off Watch this video see where they hide this function
Run's out of fuel before the gas guage shows empty, common repair on most vehicle specialy Jeeps GC
zhlédnutí 26Před rokem
I will show you how a split tank has a problem with sending fuel to the primary fuel pump. This why you can be driving and your tank shows fuel in it but you ran out of gas. This a very common problem with Jeeps, BMW or anybody who has a double sinding unit. When measures differant then the other the out come to the guage will be wrong and you will run out of gas before it shows empty.
Gm Starter Circuit, how to see why the ecm is not allowing the starter to engage with the engine
zhlédnutí 218Před rokem
Showing you how the starter works with the ignition switch, bcm, transmission module, and ecm. These are the main things to look at when your car is not cranking. Learn and keep informed on how to use the scanner to your bennifit.
Ford Pull Handle installation only the Handle, Changing the handle and forgot how to put it back in.
zhlédnutí 28Před rokem
Ford Pull Handle installation only the Handle, Changing the handle and forgot how to put it back in.
Crank Sensor Testing While computer is unpluged and crank sensor is hanging down from the engine
zhlédnutí 214Před rokem
Crank Sensor Testing While computer is unpluged and crank sensor is hanging down from the engine
Blower motor, how a blower motor works, and the voltages and ground to make the circuit function.
zhlédnutí 170Před rokem
Blower motor, how a blower motor works, and the voltages and ground to make the circuit function.
Zeus, why there is a difference between all the other scanner's, how to get the most use with a ZEUS
zhlédnutí 90Před rokem
Zeus, why there is a difference between all the other scanner's, how to get the most use with a ZEUS
P0171 OR P0174 Fuel system too lean, how to find a vacuum leak on a engine, using your oxygen data.
zhlédnutí 114Před rokem
P0171 OR P0174 Fuel system too lean, how to find a vacuum leak on a engine, using your oxygen data.
Brushless fuel pump, or a 3 phase pump, how your computer control's the fuel pump pressure
zhlédnutí 905Před rokem
Brushless fuel pump, or a 3 phase pump, how your computer control's the fuel pump pressure
C10D0 Electronic brake control system, how to reset a ghost code, reset the car into default mode
zhlédnutí 6KPřed rokem
C10D0 Electronic brake control system, how to reset a ghost code, reset the car into default mode
How to program a Ford SRS module using as built data to program it. J2534 programing srs module.
zhlédnutí 590Před rokem
How to program a Ford SRS module using as built data to program it. J2534 programing srs module.
Ford U codes you will be surprised on the answer you may even think there is a ghost in it
zhlédnutí 139Před rokem
Ford U codes you will be surprised on the answer you may even think there is a ghost in it
Seminar part 3, how to check resistance with out replacing the fuse, how to use a low amp properly.
zhlédnutí 52Před rokem
Seminar part 3, how to check resistance with out replacing the fuse, how to use a low amp properly.
Nissan keyless entry module, testing the reciever, door locks not working, key will not start car
zhlédnutí 1,2KPřed rokem
Nissan keyless entry module, testing the reciever, door locks not working, key will not start car
Live video seminar part 2, injector scope patterns, how to use the oscilloscope using voltage.
zhlédnutí 48Před rokem
Live video seminar part 2, injector scope patterns, how to use the oscilloscope using voltage.
P0807, How to adjust a clutch pedal sensor. Check engine light on for a clutch pedal position code.
zhlédnutí 1,9KPřed rokem
P0807, How to adjust a clutch pedal sensor. Check engine light on for a clutch pedal position code.
Live recording of Georgia seminar part 1 for how to use the scanner side how to save your pids
zhlédnutí 77Před rokem
Live recording of Georgia seminar part 1 for how to use the scanner side how to save your pids
Hummer antiteft system, on car doesn't crank, ignition switch replacement, no start for a hummer
zhlédnutí 35Před rokem
Hummer antiteft system, on car doesn't crank, ignition switch replacement, no start for a hummer
Cool story, good job not showing the new key working in the post program testing
The dme wire is not sending a signal to the relay
Are you getting rpm in the cluster or scanner
I got what looks like oil inside the booster. Looks like it’s coming from the intake. MC oil level hasn’t changed
Are you sure its not brake fluid from master cylinder
what is the relay part that you used? can you share a link?
Look on Amazon just put in relay with connector
Im going to do this on my little sister mini cooper thank you 🙏🏽 very helpful and saves $$$ her mini randomly stalls in the middle of the freeway very dangerous.
Wow!!!
Can I drive while regen is in progress ?
I wouldn’t it would probably get hot
Hi what should be the primary voltage when it is running
Your main will be 12 volts then the driver will put ground to the other side.
@@atrguide8724 thanks, so ground is always zero
thank you for this video, very helpful
Glad it was helpful!
Does It help if you replace the sensor???
It doesn't matter. It doesn't hurt that you mostly have to do this when replacing the PCM
Since it's so easy and quick, just come to my house and fix this old 91 Ford F-150
What is it doing? I might be able to give you a direction to go.
Where do i get something like that? Also, if someone was to scan after I replaced the odometer and did a proxi alignment with a different one, would it be possible to detect that it is from a different vehicle? 2016 Chrysler 200.
Not usually but being that year it may actually have to be programmed
I have a C10D053 code and this is the closest I found nothing out there in this that I can find. Replaced a sensor in the rear wheel, the sensor code cleared out but this one replaced it. Cruise, ABS assist park etc all inoperative
What year is it I can probably help you Any other codes in the other module? What kind of scanner tool I may be able to log into it and helpp
@@atrguide8724 Thank you, appreciate it. I solved the problem. I found a Chrysler service bulletin re the speed sensor connections. The wires chafe and/or fray on the vehicle side of the connection. Sure enough the wires at the connection were broken, one completely severed the other partially so. The original code was for a bad speed sensor and replaced both rear senors, then the C10D053 code turned up with the non-op cruise abs ect... Replaced the female side of the connection and that fixed it. This was a 2018 Pacifica that has a security block module so my scanner couldn't get in properly. Managed to find an patch/override module for that and cleared the stored codes, but no active codes. So these connectors, or the wires going to them are faulty. I got a generic one on Amazon and spliced it in and insulated it. Everything is fine now. Scanner Autel MaxiDiag MD806 which are only good up to 2017 and I have 2018, but once the override module is attached it worked fine.
I need a scan tool that does cheeper abs wheel speed sensor. Any recommendations?
When it comes to that most scanners will work, so to what you are used to.
@@atrguide8724 live wheel speed sensor data is what i mean not just a error code
Why did you bother opening the old controller if you were going to replace it anyway? Also, was the controller IC also broken? I'm thinking you could change the blown MOSFETs.
Informative video! What did you spray?
It can be anything that will ignite, this was Brake. Clean
This is amazing, is there anyway you could help me run through a problem I’m having with my 2013 Dodge Charger Module Programming?
Email me learn@atrguide.com
Great stuff!
Thanks!
My heater is blowing fuse
Thanks its work
Welcome 👍
worked perfectly Thanks ATRguide saved the day again
Promo'SM
Very common problem first place to look is at the first pivot point.
Hi thanks for the video! I have the same error in my car, how did you connect the multimeter to measure the voltage?
I just had on ground then the red on signal side, if you are using a regular volt meter
Cool thanks! It looks like my car's pedal isn't adjustable though 😕
So what you are saying is a bank 1 sensor 1 reference voltage low (P2245) means it could be any of the 4 sensors could have gone bad.
No watch the return voltage and it will tell you what sensor is bad it should be about 3.2 volts if it’s bad you will probably read 5 or 0
perfecto lo cosegui gracias
THANK YOU SIR you are the man
Thank you !!!!
You're welcome!
I don't get it. What was the fix?
It was the wireless module I wanted you to see how you can see if it bad or good
Is there a way to utilize a multi meter to do the same diagnosis. Take the module and connect it positive and negative. It was show a fluctuation of pulses. When you push the button, would it not?. My issue is 2017 maxima.. Battery depleted completely the other day. Since I have lost remote lock and unlocked remote start. But proximity key works when I'm close to car. Open doors and key can be in my pocket when I start the car. I have only lost the signal for the buttons. No panic no pop trunk no lock doors no remote start. Could it be this module.
Wow it works... thanks great video..
Glad it helped
Nice video, awhile ago I had an issue with 1 of the remotes it's electricals must of got damaged. It basically drains a new remote battery in 2 days. So I started using the spare recently. Anyhow the second remote locks unlocks fine but now the smart exterior unlock button stopped working on the door handles which was a nice feature to have, my guess thee antennas need replacing because it's not picking up the proximity Or it could be a the button switch problem. The trunk still works fine and will unlock but that has a separate antenna. I now have some voltage draw and even dealership couldn't figure it out and pointed to bcm. I tested all fuses wiring etc and all seems fine do you think it could be the module or the frequency thingy or where would you advise me to check
Yes, door and key ignition work separately need Togo to the module and chec from there
How do you get the controller box out? I have access but don't see how to get it out. Thanks!
Paul the back seat out and should just be 2 bolts holding it
Do you happen to know the part number for relay box
Great video! Very informative
Would you happen to know if this works on an E38 740iL as well? But my trunk is stuck closed, and the same shit happens when I press my brake pedal, or activate the turn signals lol. Never seen anything like this before.
It’s possible with bmw check to see if it is there. If I get a bmw in I will look to see and let you knoww
what do u choose scan ?
I use a snap on zeus it’s simple to use or triton d10 It depends on your capabilities.
Any diy level scan tools perform this task?
This fixed it and there was no codes but the same code showed up the next day. Did this really worked for you ?
Yes it did for me never came back to me
Did you fix this code? the same is happening to me, please let me know what you did
thx for info, saved me from headaches. good video
Thanks for the thumbs up, if you would like me to do a video on a specific part or car just let me know.
Nice I haven’t messed with 3 phase pumps yet but been to classes on them
Please do you know how long it takes to? I have been sitting in the truck waiting for 30 minutes??!!
It will depends on how bad the exhaust is I seen it go over a hour. If it still does not go through you may have to have to send and cook it
How long did it end up taking you Sam?
I put in a used abs mod and of course the vin doesn't match, is it worth me buying a cable and software or something to program the abs, or I take it to a dealer. What's cheaper?
If you buy you can do more than just the one, if you don’t do that many then find someone who can help you
Hi, my car is keeps blowing the fuel pump fuse . Where should I be looking in order to figure out what's wrong?
I would look by the tank and may disconnect the fuel pump to if it still blows the fuse
@@atrguide8724 I disconnected the fuel pump and still blew the fuse.
Whaaaat. Nice.
You The Man!!!!!!!!!!!!!!!!!!!!!!!!!
Good job thank you
Welcome 😊
does launch x431 program toyota abs?
It should it not a programing it a calibration, most scanner's would be able to do it.
Your guides are great! They have helped me alot.
Thank you, I will keep them going.
SWEET, that did the trick, thank you!
Glad it worked well for you
2.20 minute it is look like a injector waveform
Just remember we are only measuring the coil induction and not back Pro-been the ignition or injector
@@atrguide8724 That image has pintle hump from a mechanical solenoid.
Currently trying to do this on a 2018 f150 but when I type my vin into the asbuilt it brings up codes and none of them are in separate titles like pcm,abs etc it’s just all numbers in columns no titles to the codes
Try downloading it and the do automatic and see what happens
Sometimes you have to do automatic as built it should come up when you go to programming
What program/software are you using in this video?
This one is a Snapon Zeus but I have multiple scanners this is my main one.
About a year ago, my USB port quit charging my phone. Replacing the fuse would fix it it for a little while, then I just gave up and use a power pack. Now all dash lights come on (sometimes fixed by re-booting the system), moonroof won't open and now AC blower motor goes in and out. Conked out yesterday, then comes on when I hit a bump. Worked this morning, now out again. I don't want to get ripped off diagnosing the short. Advice?