Video

Not oms , not beeping , continuity

Did you need a gasket?

How much should a job like this cost, but only changing the condenser? I have a 2023 and had a similar thing happen, but only through the condenser. I found a new condenser for around 80 bux, and I read you need to replace the toyota/denso inlet/outlet clips everytime I'd like to just do the job myself, but right now I don't have the tools or the space Edit: also just wanted to say thank you for the video

Do you have to bleed the coolant of refrigerant? Or after replacing its good to go

Thanks bro

Thank you so much for this video; it gave us confirmation of our own experience. Watching a guy built like you struggle was some relief to this elderly couple's struggles to restrap a patio chair. Now we're laughing, before we were frustrated and felt like failures. God bless you for sharing. (Only 92 straps to go!🤣🤣)

Good video. Mine is leaking antifreeze inside the cab. You think this will be my problem?

That part where the lever does Nothing Scared the & %%s out of me!! Im veryExperienced with Engine know but not Transmissions!!I go underneath to check and the manual trans lever is completely off! Another Learning lesson! Thank for sharing

Is this the same procedure for a 2018

please do a video how to rewire a new control for that pump

well explain i jusy subscribe i like videos from people like you trying to help others and not just making mpney from videos

I just had to do this. It’s a pain in the butt but it’s doable.

How many quarts?

I can’t get that piece off on the condenser

You skip showing the hardest part. I’m out

Anytime you have to do that to a part, you've got the wrong part. The correct part for my 2008 GMC Sierra 1500 was a (dorman 14110). There were four pieces in the box for $12, but only one fits. A small black flexible bushing pushes into the linkage with ease, and then clips on the rod. No tools necessary.

What about the fan?

Thanks sir!

Engine maintenance required...Not oil re

Buddy, if your engine is making a ticking noise, the last thing you want to do is rev it higher. If your knee starts making popping or cracking noise, you don’t go running on it. You want to find out what’s going on. Did you add oil after draining old oil?

Did you even bother checking it oil? Seems like it could be low lol

ya you need to rev it up to cycle that oil thru the system. surprised that this motor does this. I had the 2gr also, it never did that after oil changes....

Usually, I just let the engine idle for 5 minutes after an oil change. Most passenger car oil pumps are electrical, not mechanical.

😂 3k fix

Holding it at 3k rpm then redlining it is called an “Italian tuneup”

No

Is there a reason why they melt/break?

If a big guy like you had difficulty, there's no chance of me doing this, but great video.

Como se llama esa pieza

Hey Sanchez, HELP.. Which hydraulic port is the UP port.. Is it the one on the Right hand side of this video? Kind Reg Adam

What a Liability!!! Wow... no protection at all.. why even wear gloves 😂

My 2013 Sierra with 67000 miles just pulled this crap on me last week…gonna try tk fix it today.

Don't shave the bushing, you are supposed to put the bushing in hot water to soften it so that it goes in easier. If you shave it off it may not have enough material to make it stay in the hole

How do you shave it off 😅 having the same issue thanks for the video

You put it on backwards !!!!

I sit here now, stranded. Car in drive, ebrake on. Fukin GM. Couldn't use a metal retaining ring? Stupid design!

Hey thx for taking the Time to show this I would suggest you put a plastic wire tie around the area of the connection of the cable selector and the bush as a safety

you put it on backwards

Thank you!

NuthaTrucker!!!!💯

DPF not DEF injector ;also known known as 9th injector. GOOD video!

I like this video because it was a "layman" doing it and you showed how it CAN be difficult and how to resolve it! Thank you!

Ok, so i cant belive it took you 4:32 min just to record how to change the shifter cable bushing and at the end you did it wrong.... DONT trim or modify the bushing, use pliers to make it fit in the shifter cable end.... the reason why its hard to install it is to avoid any failure in the future....

Any idea on bolt specs for the injector? Cant find ANY information online about them for replacement bolts

You put bushing in from wrong side

Seems to me there should be a bolt with a nut on the end so it doesn't just fall off. I guess Chevy decided it wasn't important

Haters are always going to say bulshit that i put the wrong not true the way i put on is still on my truck is hasn't pop out .. it has bien about 3 Year's that i fix it still going 😅

Awesome video. So if it’s not the injector is it the pump??

Can I jus say.. screw this Diesel 🤦🏽‍♂️🤦🏽‍♂️

omg. No safety glasses and mirrors should have been taped with duck tape. this was a disaster waiting to happen. It also made a horrible mess with shards of glass.