Video

Is this efi?

What. Did you use to remove and install those doors carb nuts. Such a pain in the ass

Hola buen dia tengo el mismo motor..arranca y cuando acelero el motor se para..como si se quedara sin combustible..el carburador esta perfecto..sera la bomba d nafta??? Me seria util una ayuda

Great job on this video, good detail

Great choice of music……

Great video thankyou! But I’m still having troubles…. Any ideas on the next troubleshooting check?

Just bought a boat with this motor. Now I feel confident to do the carbs.. THANKS

I just replaced thermostats and opened the heads to clean the passage lines and it's still peeing warm water.. 81 Johnson 140 V4

What year is that motor

I really like how the carburetor comes off after removing the choke leaver. Easy peasy.

Thanks for the video but can the thermostat keep the motor from Peeing? I've clean the pee hole and it still won't pee. Do you have any suggestions for me? Thanks

Sounds nice, How fast. ,On mine 40 same year, 60hp carb, add timing,cup 17p got 35mph

Thanks for this video! We just bought an 88 ranger 393v that came w a 6 cylinder 87 Johnson 150. The oil injectors removed to run 2 stroke. This is my first bass boat and power engine, so I'm trying to learn as much as possible. Again I'm completely new to motors, sometimes she seems she's a little rough on idle so I thought, hmm maybe the carbs need cleaned

Need a “how to” video Before i just start drilling 😅

I just bought this same motor but it's missing the plate with the serial and model number. Do you have them on yours, I need to replace a few parts

Do you have the model number for this, I think that I just bought the same one from fb market place and I need to replace a part., but I cant see any model numbers

I know this is an older video, but did you happen to know what year this motor was? I just picked up the same exact model yesterday and it needs a starter

How many starts will you get out of this without the battery dying?

Hi...I have a question for you 😇 It's possible to modify a 9.9 Johnson (Year 2005) to 15 hp...?? I need a new carburettor, and what else..?? Thanks... E greetings from Italy..😇😃😉 (excuse my terrible english)

You wouldnt happen to have that bracket and recoil do ya? Need to do reverse of what you did. (going from starter to pull start) Great video!

Thanks man good video

Very often we take youtube postings like this for granted. I have a 1993 15 HP Johnson, and I wanted to clean the carb. Your video enabled me to get at the carb in 5 minutes ! The little metal rod was the clincher ! Thank you very much !

So does the water go through thermostat before it gets to tell tale? Why does it need to close? What is the negative of just removing it and having water flow around head at all times instead of only when thermostat opens?

Thanks for the video, I am working on the same motor, rubber tip is worn out, searched high and low for a carb rebuild kit. Thanks

Thanks for the video, I have the same motor, I've searched far and wide for a carb rebuilt kit, can't find shit, rubber tip on needle is worn out. Thanks

Very good description. My motor gives problems at the start of every season. Also the gear change lever breaks if you lay the motor down on that side. Will never buy another Mercury. Yamaha for ever.

Im glad to see that with 3 people. I just bought a 30 for my 16 V.

Is it easy to rebuild ?

Very well explained. thank you.

Thanks for the video I just bought one for $50.00 with controls and a stand, He took the throttle actuator off of it for another outboard, it has 155 lbs of compression in both cylinders

Wat did u do to fix tha idle i have that motor and we i put it on slow it shuts off

Where are you located

I have one of these runs great but it's the slowest motor I've ever used lol

Good video

👍

What year is motor?

So sick. That thing would be awesome with a big tiller handle

Choke removal 5:25 and install 14:05

antique is 100 years or older.

Do it for dale brother

Great 👍👍👍

Dam you’re a genius! Brilliant video

What size pitch were you running do you know?

got the same engine, was out at sea and the engine stopped on me, I think the carb is dirty. Hoperfully once i get it off and cleaned it works with no issues

Great job, I appreciate the video. My brother has a 35 oil injected I couldn't figure how to get the carb off. Now I know how thank you again.

Thank you so much for making this video about the float on a Mercury 35 horsepower. Our motor was slightly different but it gave me the confidence to tackle the job. It helped tremendously and thanks again. Have a great day

Thanks mate. Very detailed and extremely helpful! Cheers from Tasmania.

Hey, thanks so much for making this video. I'm a girl trying to figure out my old fishing boat and motor I just got. You're making it easy to learn!!!!

I have a problem with a carburetor like that, can you help me, or how can I contact you?

I went to pump up my bulb and gas came squirting out what looks like a jet on the top. Is that the float? Thanks so much for the information