Video

The O.G.!!! Thank you.

I was wondering how someone was supposed to clean the boilers. I have that same boiler. I didn't realize you needed to remove the entire gas assembly to get to the burners.

how did u recondition the pulley ? It was completely rusted. Can you please show us

Klein makes the best crimps, they are the most widely used crimpers in the industry i have ever seen. Even in Automotive Electrical to Residential Electrical, even too the electronics industry. Just sayin.

It's a taper lock bushing

excellent. Love your videos

thank you for such educative videos. Really amazing for people to learn.. your techniques are very professional !! Great Job

This guy is def Albo 100%

QUESTION: We have several Liebert crac units with water cooled condensers. Currently we use approx 70deg water flowing through the condensers. However, we need to know if we used 55 degree water would it drastically effect the units efficiency. There is a condenser water control valve in each unit. I ask because there are no parameters recommended in the owners manual. Any help here would be greatly appreciated.

have you cleaned the heat exchangers on these yet

Not trying to be a dick, but a barring heater or even throwing them in a toster oven will make them slide on like a condom.

Good stuff brotha 😮

vamons

lol

mmmm chocolate (shown in 4:13 in video)

What number is the emery cloth you use to clean the shaft prior to pulling the hub? Also is the locking collor directional that goes behind the bearing...does it have an inside and outside? Thanks for the great information..

I almost always do all fan bearings at once, that one looks nearly impossible to access the other side

Hi,, is this taper lock 55 SF ??

Add to the confrontation IREGA Spain, a specialist in adjustable wrenches and one of the remaining manufacturers in western world of this specific tool. You can get it e.g. rebranded Channellock US or Wright US or even Virax FR... Once upon a time Bahco (SNA Europe / Snap-on group) were made in Sweden, today they are actually made in Spain. 90% of the adjustable wrenches manufacturing is made in China so most are rebranding of them e.g. Crescent a US brand. Nonetheless there are some interesting exception: Some BAUM made in India and some old GEDORE made in Southafrica probably discontinued.

Can you make more videos on shaft alignment bad ass videos 💯

Good job Martin good shitgood videos emin learn a lot here from your channel keep up the great work! 💪🏼 we do light commercial work over at Pga west in La Quinta California about too change a motor bearing on a 5 hp ballador motor.

Useful video, I’m a power plant operator and this was very useful. Thanks.

Just wanted to say thank you you have no idea how this video just saved me on a job where I never did this before and your video got me through it

Love it....

I fucking miss this guy. RIP brother

Pipelines use "pigs", or"pucks" sent through pipes to scrub them clear. Have you considered if that is an option for your risers?

When water evaporates, what is left is brine.

Thanks for this video. It answered my question about how to separate the hub and pulley right off. Awesome.

Hi, I tried to do a pump down on a carrier condenser but it keeps cutting out 2 or 3 seconds into the procedure. There's are no low or high pressure sensor. What can cause this? Thanks

Hahahaha click click.. hahaha

Great video brother 💯💯💯💯

A bit late in the game... but wish the part when you take out or put in any of the burners was included. That is what I am looking for.

nice info bro.thnx a lot

Supper.

I really hope you see this, but do you suggest I put a locktite blue for the bolts? My co worker was telling me to use. This is for the Air handler pulley flywheel. What about a lock washer thanks.

Nice little bag, the adjustable 🔧 wrenches are nice to; who makes them?

I'd like your opinion on the Emerson 49P11-843 SureSwitch Relay? I am thinking of using these on the condenser units at my home. Thanks, Jenkins A/C & Heating

Hi what GPM stands for? Thanks

1:01 Sully that you!?!?

Thx bro watched your video busted my ass woke up early and was 1st on the rope for about ten years now. Learned a lot the hard way and now I'm represented. TWIY

Román kontár meló!

how many times this should be done in a month?

We are having problems with the make up line the guy who is here to turn everything off doesn’t know where it is

Yo I have a question, if I wanna replace a bearing, how do you measure the old one? Or do you just get the middle and serial of the unit and give it to your supplier ?

Still the Best! Thx Emin

Very cool video. love the old equipment. Never seen a cooling tower that small and in an attic.

Someone greased the shit outta those bearing

You shouldn’t Meg a inverter compressor. You can destroy it.

He's passed away guys

Fuck that. Obviously don’t cuss In front of customer. Be yourself in the videos. If your making videos for other mechanics cuss away. If your audience are customer then yea clean it up. Stay real.