Video

It's was all wrapped in gloss black, window trim, door panels, front grill outline, roof rails were done in matte black, to give it a factory black edition look.

Glad I could help.

You're welcome!

Glad it helped

Was a bad TB, my car would get to a certain speed/rev and not pick up speed.. very sluggish and occasionally jerk mildly. I change the TB and it was all good. The codes didn't point to EGR.. but it wasn't the EGR.

I don't have this.. but I do have a Celica GT 2005 in Thunder Grey.. I will be adding a video on here when then sun is out and temperatures go up a little

@maj6150 what has 2zzge... is perfect mate!👌

Sorry I sold it about a while ago.. still kick myself for doing so.

I honestly can't remember now.. I think I only removed a rubber hose to access the TB

@@maj6150 cheers. May as well remove the EGR and give it a clean as I'm working around there.

Never a bad idea to remove the EGR and give it a good clean.. I use oven cleaner (foam)with very warm (not boiling) water and let it rest for 10mins and then clean it with a wire and toothbrush.

I didnt hard wire it as i change cars every 8-12 months.

Hi, sorry i sold the car now.. but if you see how i did it.. i can assure you it wont cover the airbag as the wire is tucked away just under the rubber seals and on the edge of the panels. Also the impact of the airbag id so strong when deployed you have any issues with that wire.

So glad i could be of help to someone.

Hi thanks, that look i wanted "subtle". The exhaust sounded no different at all to the stock.

My car is 245/40/19 bolt pattern 5x114.3. I know someone selling some 🔥 rims and tires same 245/40/19, but the bolt pattern is 5x112. Is it possible for me to buy despite the bolt difference?

@@MrStylish126 yes, they fit , i use 5x114 on my cars wheel hub 5x114.3..i have a video you can watch on youtbe click my car okn my name here on the commment...........step 2 .my car hub bore size is 64.1 the wheels i have are 66.6 bore.. remember you can always add centric rings sizes up to add more , but you cant take away. you cant take 64.1 and make it smaller with a centric ring if needed.

Please bro i need your help i have mercedes wheels i want to put them into my honda but there 2m difference? How did you do it?

@@MohamedTechQ no the 2mm different isn't even noticable. Perfect fit. But get the 66.6 centric ring to 64.1 bore. That's all. I use the wheels direct for. 5x112 on my 5x114.3. And that's for accord too

Nope.. its tucked in on the edge away from the airbags. If you lift the runber weather strip, you can just sit it there

These side steps are from Direct 4x4 in Derby, can remeber the name of them. They were about £250ish supplied and fitted

@@maj6150 yeah been looking mate is it raptor ones? How have they been so far? Want to beef mine out with them but want the right look. How has Maxton kit been? Rear spoiler next?

All the bits have been fine and holding well with the test of kids and the mrs 😄

I didnt fit them.. was just checking they can be fitted with wobble nuts which they could.

@@maj6150 Good try! Aftermarket no brand wheels a lot is PCD113. But workshop just tighten with normal bolt & nut instead of using wobble bolt/nut.

Hi Martin, its literally on the edge, you cant push it futher with you fingers even if i tried unless i used a tool push it in.. its well away from the airbag.. but thanks for pointing that out and i will double check it.

Hey Ace - I agree with Martin. It’s certainly blocking the airbag in the pillar. Unless you’ve removed the SC few and tucked the wire under the airbag. Otherwise it’ll be constricting the airbag. Do check.

Its from Maxton Design and i didnt get the side skirts

I regret selling mine.. but i had no space to keep it safe and inside. But them ZX are as good as next to mone.

Yeah it is..sorry for the late reply

@@maj6150 👍🏻👍🏻👍🏻

Here in the UK, if the engine has been cleaned, people think there is something to hide as in any oil leaks etc.. so i tend to leave the engine bay so anyone buying it can be satisfied there are no leaks etc.

Hi, yeah it's 50% at the front and 30% and the back. Remember the lower the number the darker the tint. Hope that helps.

Its a conversation done by a exhaust specialist.. all we did was get a GTI exhaust and they connected it from the back box to the tips. Its a relatively simple process and still MOT compliant. Labour was £70, and the GTI exhaust we sourced ourselves for about £150 with the diffuser. For got to add you also need a GTI rear diffuser which has two tips cut out.

Yes i used wobble nuts.

@@Adam-us4hi looking back i wouldn't use them again, but never had any issues always had a thought of "just say something happened".. so no wouldn't recommend them.

No don't need them so ble bolts is to offset it . Didn't need it torque good everything is still good today. Rides like a cloud.