Video

Boss!

Can you do a 3 point saddle over another conduit

finally someone explaining it well without skipping anything. this is the only video that i have found that is useful

I love this video he make me confident to Ben pipe thanks a lot

“Never falls out the bender” haha

The deduction for 3/4 pipe is 6". Why is he using the 8" deduction?

Very clear

The level only works if you know your floor is truly flat, which most aren’t, especially in old worksites.

Thanks Jon

I appreciate you very much for taking time to make this and share it with us! Great detail of real world experience! God bless!

Man what do I do if I only have the rise and center mark, this math is easy when you are already given all the measurements

Can you answer a question regarding a 3-point saddle using the push through method?

Outstanding ❤ 1/2"EMT is more forgiving 😅

What decides that the offset is 30°? Is it just esthetic/ease of wire pull preference?

You don't have to deduct for the 90 if you use the star and pull toward the measurement

Need a box offset

Great explanation best I’ve seen so far this one and the the sparky channel thanks

If u had say 2" conduit would you have to assemle the whole thing and set in place, not going to get much flex out of it like the 3/4

Straightforward demonstration- thanks!

Best fucken explanation

nice demonstration.

Best explanation I’ve found regarding this topic. Clear and understandable. Thank you.

awesome

Add 30° shrink 1/4 per inch ×2.5

By far the best video. 1/3 the length of others, all to the point. Thank you.

MAD helpful thanks

Just stub 90 everything and then cut and measure. More accurate and easier to spin on. Also, pipe threading can easily be done with one guy and having an actual reamer is better than a file or piece of all thread. Good video

Thank you for helping me with this I was struggling to understand it when I was reading the text book.

Why do you call them "condulete"?

Your first bend didn't have the "eyes always towards the obstruction".

Put your level on the bender handle, for 30 degrees the bender handle will be at a 90 with the ground also when doing the second bend keep your left hand closer to the bender using pressure, you bow the conduit when you try to bend farther back

If you are doing rigid conduit it’s a good practice to spin your boxes, Meier hubs, unilets on first to see how they fit. You may need to change the depth on the threads or clean them up first to thread them on tightly. This is reaaaal important. I don’t recommend using minnies because they are easily crushed or bent compared to malleable 1 holes with back straps. They make 3 1/4” deep strut and it’s a better install vs using back to back 1 5/8” strut. Always spray the cold galv on after you threaded your pipe which contains the mess. Threading rigid conduit is not a 2 person project…you can fasten the tripod legs down or use a sturdy rope to make a 3’ loop that is tied to the foot, using a piece of wood can’t stop it from flipping on larger pipes or if the tripod is an old p.o.s Finally when bending your first piece you should have calculated the gain which on newer 1” foot benders is somewhere around 4 1/2”…it’s verrrrry good to know because you cut and thread first then bend if need be. When using a foot bender I highly suggest you take the opposite end of the conduit and stick it on a wall or curb or something sturdy so it cannot slide around on you. You can really hurt yourself if it slips.

Great video! But your toolie 54 seconds in , is oiling for you in the wrong spot Too many times I've seen that power pony catch and come over top. Have your partner stand to the side so he doesn't get whacked by power pony with dull dies . 3/4" heavy used dies don't always get new teeth right away Good habit to have when you go to bigger conduit. That is why you see the chain or rope on TriPod leg to help. That is reality even with Hogs Head

The Deduct was 12 & 5/16 but we got the point . Thanks for this

Great video ...thanks for posting...but I was wondering what is the name of this blackboard that you are using

How do you check plum without checking level..? 😂😂😂😂😂

From a UK spark - what a load of nonsense.

How do you sort "plum" with out true level?............

In Watching this it's a great beginners video. For those who are watching you still need to adjust that bend for how you are supporting it, whether it's back strap or mini etc. Also if you just use a one hole strap you will prob need a box offset in the beginning of that run. Otherwise , great video.

Thank you amteck for the bending series

In my NCCER textbook on conduit bending it states to "multiply the shrinkage by 2" meaning in order to compensate for both sides of the bend. Can you please comment on this?

Bruh I made my life hard lmao 🤣

Is that same formula on the bender

WHY are these videos so rare and hard to find?

Good stuff

Thank you for showing how to spin it on. It maybe the most difficult part 😂

Gotta do them all to centers. So you can start at the end or after a 90 and bend them all in the same direction. 🤔 You can notch the bender with a bandsaw to indicate the center of _ degree bends. Quick bend app has some useful features. It has alot of info mapped out.

Nice video . Thanks

❤❤❤❤

❤❤❤❤❤