Video

@@binayaksamanta863 thank You 😊

THANK YOU ARNAV YOUR FEEDBACK,THIS MOTIVATE US MORE TO BRING VALUE TO YOUR CONCEPTS STAY TUNED FOR ALL THE UPCOMING CONCEPTUAL LEARNINGS

@@binayaksamanta863 its material property..and its already given in the sample problem data ,i have mentioned that during lecture..watch carefully ,if we go by default value of Staad your answer will not match thats why i have created material property sapertly according to E value and added

Thank You,share with all the beginners 😊

@@user-iq5zq6ss6g Yes we will continue with remaining parameters Also in the Upcoming Session we will demonstrate various types of Structures and their design requirements which co relates that why you need to specify particular parameters/which parameters you need to avoid which impacts your design..Stay Tuned 😁 Don't Just Learn Software Learn concepts 😇

@@binayaksamanta863 in design parameters everything will be covered

@@binayaksamanta863 Just For Your Information As per Section 3.8 Table 3, the slenderness ratio (KL/r) of compression members shall not exceed 180, and the slenderness ratio (L/r) of tension members shall not exceed 400. You can edit the default values through MAIN and TMAIN parameters, as defined in the design parameters tab I hope this will clear your doubt

Thank you so much for such amazing lectures @@CIVILNIRMAN

@@mohdshoaib5555 thank you 😊 stay tuned Share with others 😁✨

@@binayaksamanta863 thank you 😊

@@antonycivil7 sure I'll make a video on this stay tuned

@@sarangsahu9432 which version you are using?? Make sure you have updated version

@@CIVILNIRMAN I'm using series 4

@@dkyadav6787 thank You Stay Tuned 😇

@@arunndinesh happy to help 😊

@@ikiriyethanks 😊 most of our videos are in english

dear its an envelop so that's why it is showing worst values at all location based on envelop, whether its top bottom or mid.

@@CIVILNIRMAN Thanks again for the reply. Therefore, I could say that envelope in STAAD is choosing the critical combination of loads that will give severe effects?

@@gnidnoeled786 It is nothing but a super imposition of the force diagrams of each load combination,which simplifies your understanding of the maximum values. Basically you get the entire forces of each combination in a single place.

@@CIVILNIRMAN Thanks.

Thanks ✌️

Super soon stay tuned .✨

Thank You ✨

Pre Engineering Building Structures

Thank you 😊

Dear Salman For mono slope building you can refer Page-15, Table 7 of IS 875-2015

Stay tuned for next week ✨😊

😊✨

For which details you want?

@@CIVILNIRMAN Please make videos on shortcut methods of design, like the thumb rules to check the design for simplifying equations. Sometimes, we dont have enough time to design manually the whole structures and because we have a lot of structures to be design in a consulting firm in a short span of time so we mostly trust software results because if we come to check every single beam and column then it will take a lot of time. So, I think there have been some shortcut formulas and tricks whom we check the design. Like the stress formula Strength = My/I to check stresses in foundation. Or there might be some quick methods to design short structures manualy rather than on software. using Aisc code

When you jump into the field,each project has different challenges and lesson learnings, But yes we prepare you for the best of best till date whatever we have learnt Connect with Us for your further queries on : +918320501602

Thanks for your feedback and experience on other software 🤗, you can Share your learning experience with other software so it will help lot of other engineers too

Super soon already working on that 💫✨

@@CIVILNIRMAN Sounds Great!

Thanks for your observation,We will wait for a few more days to receive other observations than I'll post the other observations...till then keep figuring out 😁

Thank you Niraj 😊

Thank You so much Ma'm 😊

​@@CIVILNIRMANAmazing video man. Kindly provide a video on how to read electrical drawing layout of a residential building.

Thank you 😊,Hello please checkout the playlist,its already uploaded

Share to all beginners