- 196
- 179 516
Cecil Wood working
United States
Registrace 13. 10. 2019
Cutting board lessons learned.
These are the lessons I learned when making this cutting board. I will select boards with no defects and glue both sides so there are not defects.
zhlédnutí: 35
Video
Fixing a broken outdoor popup canopy.
zhlédnutí 11Před 19 hodinami
This shows an easy method to fix the folding canopy support after they are broken. No need to throw the canopy away just fix the broken support.
RV Closet Rod Locking Bar - Stop your clothes from falling off the rod!
zhlédnutí 31Před měsícem
This project will make a way to lock your clothes in place in your RV while it is moving down the road. If you are tired of finding you clothes laying in the bottom of your closet when you get to where you are going simply make this and strap you clothes in place. Have fun RV'ing.
The force of a ritter board for clamping
zhlédnutí 199Před 2 měsíci
In his video I use a ritter board to straighten a 1.5x1.5 inch board that is warped.
Method for removing tabs from connected parts.
zhlédnutí 140Před 2 měsíci
This shows how tabs are used and how to separate the parts and remove the tabs. Yes you can just sand them off, but this is faster and gives you a level surface.
Flatten the round slabs Part 3
zhlédnutí 177Před 2 měsíci
This shows a method to improve the CNC uptime and allow the operator to do other tasks while the CNC is operating.
How to surface 5 inch round log Part 1
zhlédnutí 130Před 2 měsíci
This video shows how to use VCarve Pro to surface a 5 inch slab cut from a log.
Flattening a Wooden Disk Part 2 In the Woodshop
zhlédnutí 175Před 2 měsíci
The second part takes the design and shows how to mound and operate the cnc to flatten the round wooden disk or cookie.
Turning a Lighthouse on a CNC Lathe
zhlédnutí 61Před 3 měsíci
I am working on a project to turn firewood logs into a Lighthouse by turning the logs on my Shark based CNC Lathe.
Clean up my spoil board.
zhlédnutí 59Před 3 měsíci
I am going to work on a new project that requires some tighter tolerances. The first step is to clean up and resurface my spoil board.
CNC bit breaks apart due to vibration.
zhlédnutí 55Před 3 měsíci
While resurfacing my spoil board the bit started to vibrate then snaps apart.
How to put your Mac back in the box.
zhlédnutí 1,6KPřed 3 měsíci
To place your mac back in the box simply reverse the procedure of unpacking the box. 1. Unplug everything. 2. open the box and place your mac on the flap. 3. Slide the two bottom pieces onto the bottom of the computer. 4. place the top piece on. 5. Place the mouse and keyboard in their box and place in the slot in the top styrofoam. 6. Lift up the computer from the bottom by the two bottom piec...
Dragon Sunday March 3, 2024 Launch from Bushnell
zhlédnutí 104Před 5 měsíci
Dragon Sunday March 3, 2024 Launch from Bushnell
Cars for Kids Project with our wood shop members
zhlédnutí 161Před 5 měsíci
Cars for Kids Project with our wood shop members
Project for used wrapping paper scraps
zhlédnutí 27Před 6 měsíci
Project for used wrapping paper scraps
SpaceX November 9, 2023 Launch as seen from Bushnell Floridia
zhlédnutí 50Před 8 měsíci
SpaceX November 9, 2023 Launch as seen from Bushnell Floridia
Best way to measure Pesticides without ruining your teaspoons
zhlédnutí 39Před 9 měsíci
Best way to measure Pesticides without ruining your teaspoons
CNC Lathe failure at the headstock- oops!
zhlédnutí 89Před 10 měsíci
CNC Lathe failure at the headstock- oops!
From a log to a roller in under 5 minutes thanks to the magic of high speed editing.
zhlédnutí 159Před 10 měsíci
From a log to a roller in under 5 minutes thanks to the magic of high speed editing.
Upgrading to a 3 hp spindle on CNC Shark
zhlédnutí 1KPřed 10 měsíci
Upgrading to a 3 hp spindle on CNC Shark
Added a grease zert to my fourth axis for lubing.
zhlédnutí 34Před 10 měsíci
Added a grease zert to my fourth axis for lubing.
Cherry and walnut roller made on CNC lathe.
zhlédnutí 66Před 11 měsíci
Cherry and walnut roller made on CNC lathe.
Starting a project on a CNC Shark Using the Teach Pendant
zhlédnutí 868Před 11 měsíci
Starting a project on a CNC Shark Using the Teach Pendant
EMI interference can cause this
Hi, for me the bit broke and when i put in a new one, it didnt spin again... did you find a solution?
I went to the distributor to get this coupling, but it would not fit my 2006 Beaver Monterey line. They said the coupling only works on Parker hoses.
Extremely helpful
This worked for me! Thanks!
You mentioned that the new Parker part # 2-651-r-4-4 will not work with older hose. Can you please elaborate? The original part# 20651-4-4 is no longer available anywhere.
Check with parker their phone number is 330-296-2871. I fixed my unit and latter sold it. so I no longer have hoses to repair.
You’re an absolute hero! That never would have occurred to me!
What kind of saw is that and what size? I know it's a Dewalt... but... I need one Exactly like it...
12 inch dewalt compound miter saw. If you look on face book market place they come up for sale quite often . I recommend getting the table with it.
OMG! thank you so much!!!!!!!!
Nice tip! Now I only need to build a router table ;) Tabs can also be removed with a band/disk sander, and it can finish the edges as well.
I wood look on facebook market place you can find a good used one cheaper that building one.
@@cecilwoodworking7204 Thanks for the tip, though even if it costs more I like building it. I have a router laying around I hardly ever use so it might be a nice future project.
Wow, an old Sears Craftsman, tilting head bandsaw.
Yes it's almost as old as I am and still working.
Thank you...straight to the point! I went through 3 other vids.
This would be great for the apartment life if I had something like this El Cheapo table for now until I get me a sturdy skid table made and that way I can have a can crusher device in my apartment that don't make a whole lot of noise this would be perfect and make it to work to fit all different size cans in there that will be awesome whoever made this did a great job
You did a great job in explaining what you did. I was going to comment on the dimensions but you did give them at the end!
Glad it was helpful!
Thanks, very helpful!
I had to have a new hose made. Could not find the fittings. With the 7/16 JIC female and 1/4 hose end and 153" of hose, I paid $132. If I called Exotic Automation and gave them your part number would it fit my camper leveling system hose and the 7/16 JIC female?
look at the part number on your hose, the should be able to match the at exotic, Good Luck
Difficult to find a better reason for cutting wood, than to bring a little joy into the lives of sick children. 👏👏👏
Couldn't agree more!
Sincerest respects for what you are doing.
Very nice project Cecil. Did you design this yourself and do you have a file for this? I would love to try this project myself.
Yes I designed the project, but I purchased the model from design and make. his is the company that partners with the Vectric software company.
WOW! Thanks! Worked perfect!
You're welcome!
Would you provide a idea of what the floor cost you?
A friend did the labor for me I had little over $5,00 in concrete and wire.
Hell yeah ty.
I just did the same setup and wondering if you found a way to manually run the speed controller?
No I have not.
How did you add a MYPOST PROCESSING folder or how did you do it. Also how do you get the MY POST PROCESSORS to show up when going through list of setting up a cut? Thanks Hager
Open Vcarve then open the File tab then open Application folder Inside the application folder are the two items you are looking for PostP for post processors and the other one is My_PostP for My Post Processors once you open the My_postP folder you can copy the info you downloaded from Next Wave CNC Good Luck
@@cecilwoodworking7204 thanks for the clear step by step instructions. Now I will look up next wave cnc
Nice, this is what I am looking for. It would be great if you can show how you prepare the toolpath in VCarve for a tapered cut.
Will do look here. czcams.com/video/337aQl4ItHw/video.html
The image you provided is blurred.
I use snaget to capture the images and for some reason it does not always work the way it should. I am still working on it.
Cecil, your filming of the screen is blurred + no one wants to hear your issues when viewers want solutions to their issues.
Thanks for your comments
If you put something as a fulcrum under the pivot of those Klein cutters you’ll get more lift per grab. If you use a stiff back broad knife or steel junction box cover under the cutters you can get a nail out without marking up the surface of a piece your trying to reuse
Yes I have done that with larger nails.
Dear Lord, this saved my butt. My mom had one of those stands for the angel that was cylindrical, like a toilet paper roll. i wadded up some tape to keep some two-pronged metal stakes ( like giant, U-shaped paper clips) locked in place...Slid right down and didn't budge. Thank you for the idea! You just saved me a giant headache.
Your welcome, glad I could help.
how i can contact you sir?
What would you like to know?
@@cecilwoodworking7204 sir, i watched your video, and i found many problem of your videos, if i shortly explained you, your video quality is good but in your video SEO section is not perfectly updated.. If you want to know more details about your video problems then plz provide your social media or gmail or anything else so that i can communicate with you ❤️❤️❤️❤️
very nice video sir😍,to rank do seo to your video😊
amazing video but not for seo your video dont rank
The end that screws onto the hose are left handed threads (counter clockwise rotation to install) . In the video you are rotating the wrong direction and that is why it is not going on the hose very well.
Thank you so much! I cut some really pretty dead tree wood down and it is thin enough to put on my miter saw.
Your welcome
Brilliant thank you
You're very welcome
Thank goodness for this video. Worked so well.
Glad it helped
I removed mine, but now I can't get the bit back in the magnetic bit holder.
Try a different bit, it is possible the bit or bit holder is broken.
Hi Cecil. I am unable to contact you. Can I call you?
you can contact me at my facebook page
The file seems to be locked
I added a file that is the one I used to Etsy so that you can get it there. I do not know why the other one went away.
Amazing! Brilliant! Genius!
Wow, thanks!
how about a video showing how to load and start a job using the pendant. I understand every thing in this video but I am having a hard time starting the actual job
just loaded one up for you. Hope this helps.
Excellent thanks
You are welcome
Hello, thank you for this video. What machine do you use?
This is a next wave cnc machine. I just used one of their gantries, a spindle and their controllers and made a new base. The new layout allowed me to turn larger logs, up to 8 inches.
Olivewood crafts always sell well at the Greek festival. I find it hard to get decent pieces of the wood though.
Yes it is a slow grower and does not live much over 50 years in our area. This makes it hard to find.
Wouldn't be better for the bits to remove the bark first?
This bark is hard and not easy to remove with all the knots and burls. I simply kept reducing the diameter of the cut until the center became round. This required machine time, but not my efforts to remove the bark. If you have a better way please let me know.
Are you still running your Moray laser? I just bought a Roly Lasermatic10. It has the full enclosure like the Moray has, but has far more cutting power. It also has the rotary attachment for the laser although I haven't designed anything to use that yet.
Yes I am! I would like to try that machine and then I could do some training videos on it. but that is not in my current budget maybe 2024.
Your tip worked perfectly!!!! Thank you so much. You are a genius!!!!
You're welcome!
Thank you so much. I have been trying to get a stuck bit out of my screwdriver all day and nothing worked. This worked for me as well.
Glad it helped
Hell yeaaaa thank you!
You bet!
blurry as hell and you cant follow it