Video

very very interesting ! Can I use a spray of water mist?

Good job, Spencer!

Thank you very much for the video, I'm going to do this myself soon and looking for tools, when you removed the E10 bolts holding the pulley and used an impact wrench to prevent engine rotation, what amount of torque am I looking at from the impact wrench to ensure that there's no engine rotation?

Why doesn’t the hard fuel line get replaced? The manuals says to.

Brilliant detail. Thanks

What were the symptoms to know that it was the HPFP?

Claw hammer are you serious ???

Where I live 2X Year. Thanks for a VERY helpful video.

Yey, I get to replace mine just because it's gasket has failed

is this the same for the R56 LCI bmw engine 2012?

What is the cause when the trunk is filling with water? How do I fix that?

So the dealership is trying to charge me $1665 to replace the seal. I do believe u will be looking elsewhere for the repair lol

Tried compressed air and it’s still clogged on the passenger front. Tried using some weed eater string and can’t get it to route down. Any tips?

I just got the P3091 engine code and very rought start. Engine was really shaking hard and started sputtering. Didn't stall out. Rested it in a lot for about 30 mins then drove home. I looked around and found a fuel pump on Ebay for $259. 3 year warranty and says Genuine. So, ill be working on this project next weekend.

would this work on a 2019 countryman? I know they're a little different.. dealer wants $1800

How much do you charge for this service? My mechanic is charging me $600

Very satisfying to see the water flow...

Weed wacker line works good and will not blow off hoses

the repair place said that the component needs to be programmed after replacement. True or False?

Don't use air you will be sorry if the tubes blow off.

I really appreciate the video. Gonna give my mini a shot with this video as a guide. Thanks, 👊🏻

The audio for your intro; how did you get that tone?

Always inspect the lip of the seal to make sure it is not rolled or curlsled. I'm sure it wasn't in the video, just an extra visual precaution to take because these seals can roll if they are put in by hand with uneven force. Again, the video was good! Just saying it's a good thing to look carefully at it. If an edge is curled an angle pick can tease it back out into place, just don't scratch that hub.

I appreciate the help

🧡🧡🧡 Thank you!

Thanks this solved my problem!

My diesel engine only has the single middle bolt and not the 3 which engine have I got on my 08 mini?

On another video they detensioned the belt with a wrench instead of the special tool but had to have someone push the pin from the top while doing so- why doesn't someone have to push the pin when using the special tool at 6:30?

What tools did you use? What length to get the spark plug out? Any links to Amazon or description would suffice. Thank you in advance.

This video is exactly what I'm looking for, but I don't have one of those air gun thingies. Is that an air compressor? Can I get one cheap? And what attachment are you using that is the right size for the drain holes?

That's N18 engine

Thanks for the detail instructions. Just 1 question, the White coupler you used to push in the seal, is that a special tool or just a 2” pvc drain pipe?

Mini cooper 1.6 2005. Soaking Oil on passenger side floorboard any idea where the oil coming from?? Please help. Thank you.

Straight to the point video! Also if anyone is worried about the white foam layer it depends on the climate you are in to prevent where there may be a lot of pine needles, pollen, etc. Or where it also gets cold and prevents ice formation on the air filter paper itself!

You should always put oil around the seal when driving in

How much low was the fuel pressure in comparison as the set value for the hpfp?

Thank you very much sir for demonstrating how to install the drive belt and crank sealant.If not on your video I will not learn how to install them because it is very tricky.Lastly,may I know the part number and the size of the serpentine belt you’ve installed.Thank you and more power to both of you!!!😊

Cool!

At the bottom of my gearbox, oil is collecting, and I suspect it's coming from the crankshaft sensor bracket. Should I replace the crankshaft sensor seal or the bracket?

Holy what? You guys are back! Dude we definitely missed you guys

extremely detailed video, im impressed ! you must be a master tech

👏🏼👏🏼

I’d be careful using compressed air. That rubber boot on many of these is just a slip on fit and the air can pop it off the metal tube. I’ve found weedeater line used gently does better and prevents the boot from coming off

Very Easily, Understandable Video. Thank You For All The Helpful Information!

👏🏼

Wow, super informative. Thanks Madness Motorworks!

Thanks this video, I have a question: pls tell me how to remove 2013mini cooper gearbox close to limited slip differential? I'm blocked here ,thank you so much !

Have you guy's had any problems with any of your LSD installation?

Hed MiniMadness, I just started to work an my MINI. Your videos a very clear. Can I install the same Swybar on an Mini Clubman? Thanks

I just did mine watching this movie! Thank you MiniMadness!!! Hope we could buy your product here in Japan.