Video

hello, I bought the system, The speed is ok. but the vibration siginal is not stable. I don't know why, can you give me a guide?

Hocam önceki uygulamanızı çalıştıramadım arduino ve mpu6050 sensör ile uyumlu değil galiba

nice to see you posting again:) I have followed some of your earlier stuff I play around with similar things

Sorry, omit that question.

Hi Larry. The Mark 20 and Mark 10 use the same air bearing shaft ? Where did you buy your speed sensor detector ?

I want to purchase this setup possibly X2

What is the maximum speed you can balance for?

I want to buy it, it could be delivered to China?

It is an amazing video. Have help me many.

Awesome ❤️❤️❤️❤️

Yazılımı lazım bana

Hello friend, this equipment is really cool! I downloaded the arduivos but the zip of the software you are using has a password to open the zip! Do you know the password for me to unzip or is this software paid? thank you very much!

Usta bana bitane göndersene veya eloktroniklerin isimleri nedir

Can you share the software for me?

I want to buy this product. Thank you

I want to buy this product. Thank you

I watched this whole video hoping you would show how to identify a precise angle for weight placement. such as suppose the software says put a weight at 243 degrees. other than eyeballing how do you identify location. Second thing I was hoping to see is how far out to place the mass. It appears the answer is "all the way to the edge". So annoying to have you go into detail about the math coefficients and not show the measure placement of the weights. The other question I had was why you identified the inner part of the dumbbells as plane 1 and plane2. Maybe because that is where you knew weights would go. If I had specified the distances in the software to the outer surfaces could I have placed weights on the extreme front and back as well?

I am surprised why only 23 likes so far for such a rare in-depth technical video on prop balancing, it's like a award winning video, thank you so much !

Nice setup! What is the name of the optical module? Is it just for an index pulse?

great stuff mate. Thank you

wow

thank you for your awesome product, I bought I set... and now play around :)

Too bad impulse 2 is not available

Muito bom mesmo obrigado pó as esplicações

Please provide information video to how to order this kit and how to receive kit, Full process video "order to receive"

Can you balance eg. Table fan propeller without removing the prop even at some accuracy? If yes, what weight of propeller should be used, should the weight include the motor?

Can i ask an question my granddad has the software everything. But when he spin the motor up the rpm are all over the place . From 0 to 100000 to 70000 and sometimes it dont give any signal. We used the ir that you can use 150mm away. We played with distance . But nothing works . What can do wrong

Please provide the software file

Calibration is compulsory for every time's ??

Can you deliver in India?

Hey bro can you provide this product for large size of blower impeller balancing

Will this work for small motors like 12-13mm? Also 3" triblade propellers? If so sold. I mainly build and fly light 3 inch quads. For now I've been doing the pencil lead and tape balancing for bi blade props but motor bells are another thing.

Are these one piezo sensors ? If not would it be possible with piezo sensors ?

Good

Desperdicie todos esos minutos para algo que ni sirve, dificil de balancear y no quedaría a altas Rpm.

What’s your fastest balance speed?

Very informative and super product. Thank you

Loose the background music

can i buy it

Hi i am Rainer, the manufacturer of the Jetfans. Your products are looking good! Just my 2 cents. To get the maximum thrust out of any EDF-System, you need the origin Open Duct Lip! WIthout a belly mouth lip, you will loose around 40-60% of Thrust at the test bench!

I would like to use this for balancing Compressor wheels for turbochargers, but I see the motor is connected directly to the shaft for this item. Is there an easy setup that can make that the motor doesn't have to be reconnected to the shaft every time a new compressor wheel needs to be balanced?

The great Mark . dear can you provide us this software , interface and sensors plz

can this balancer be used to balance an RC Jet engine? the engine is basically like your setup here, except it, can't be spun with a belt I'll have to use compressed air.

hey mate do you guys deliver to New Zealand?

I am so glad I found your channel. I was about to develop something for my own purpose :)

Is this laser method much more better to "accurately" balance or strobing with a light can provide the same level of "accuracy" of balancing?

9:13 - Your PC's wallpaper image is cool...

Which dc motor You using for spin the shaft?

put youtube onto X2 speed to watch, perfect to keep you awake

I performed a balance on some of my E.D.F.'s earlier this year. I used the in infrared sensor to indicate the speed. Everything worked well, until yesterday. I cannot get the infrared sensor to function. Is it alright to perform balancing without this sensor ?I