Video

Thanks ,was able to fix my microwave

Mine blows the fuse but it’s after it’s worked for a week. I’m guessing it could be a door switch. Because I’ve replaced the fuse twice and each time it’s worked for a week

where did you get those struts, i do have leer cover on my truck but cant find any 19.7 inch is the full size once its extend , the cover is heavy should i go with 250 lb . where can i get it from . Kindly guide me plz Alawi

You spent more time showing popcorn than the problem. Do you think you need more practice at how to video the problem? Was the popcorn nice? 😂

Thank you for posting this video! Helped me out a lot!!

This was rough. I tried getting fan off. She didn’t budge. So I trimmed the shroud and pulled her. She’s burping right now.

Would have been nice to show how long it took to fill a pail with water in the beginning . Then after the fix ,how long it took to fill same pail. THANK YOU.

Me: Did you fix my microwave? Allen : try the popcorn and subscribe buddy 🍿 ✅

Thanks a lot for the tip. I changed the door switch but I guess one of the wiring got mixed up as it keeps on blowing a fuse.

Can only outside spigots have a loss of water pressure while inside still has good water pressure?

I need to do that. Did it solve the problem? Runs better? Better mpg?

Good video. Turn that wrench over so the torque is on the fixed jaw. Just some friendly advise.

Good Work, Question What Kind of Rubber / Plastic Plugs Did You Use On The Lower Transmission Lines ?

Thanks Much for this really good video!! I was relieved there is a chance we don’t have to by a new microwave!!

Why can't you just shut the water off on that line?? Why you gotta shut the water off to the whole house?

28:13 That adapter just behind your left foot goes between the top of the ball joint shaft and the forcing screw. It's shaped inside to center the shaft and not let the forcing screw walk off the top.

Thank you for the tip I just got mines paid $45 and going to install it this week hopefully it goes as simple as your's did 😄 ty

Thank you for this!

There it is what

SO ALL THREE SWITCHES ARE THE SAME AS U DID NOT MENTION?

Was not my issue unfortunately. I have the same model. I watched this great tutorial and bought both the switches and black holder together not to have to do the work twice. I tested and retested the switches while in place for proper opening / closing with the door open and closed. All was find. I plugged it in , turned it on, fuse blow in split second. Oh well. it is 14 years old. guess it is time for new one. Thanks again for this video and update.

Good stuff! Heading to HD and try this now!!

it is so good to see a father and sons working together

damn those are terrible switches

Just disconnect the middle switch and leave it unconnected to the switch. You will still have the other two switches for safety. This is bypassing the blown fuse.

I'm an electrical engineer and saw the schematic. If you want to fix the fuse blowing without spending tons of money, just cut the single white wire on the middle (normally closed) switch. Do not cut the other side that has the white wire and black wire together. Tape up the white wire so it doesn't touch anything. This will disable the fuse blowing and your other safety switches will still work normally. Replace your fuse and plug in the power cord.

Thank you. Our 9 yr old GE has started tripping the breaker a few seconds into cooking. I took out the three switches. The middle and bottom look fine. Pulling apart the top switch I found that the contacts were welded together (any idea how this would happen, we never open the door until it's finished). I pried them apart and hit the faces with emery cloth. It's still popping the breaker so I guess it's time for a new switch.

Good video and great teamwork. You're both on the right track.

To prevent that high pressure fuel spray off, you can remove the FUEL pump relay in the engine fuse box, i think is relay 41, run the engine till it stalls, then when working below the truck, you can see a cap in one of the connectors, it is the fuel pressure relief valve, just put a pen or something so you can get out any remaining pressure , that way when you unhook the fuel lines, yo do not get that surprise fuel spit out.

Our Frigidaire Microwave stopped working after the power shut off to the house. After the power came on again, the Microwave interior light comes on, but the unit will not start. The display screen won't light up either. Any ideas on this? If it is the switches that are bad, where can I order them and are all 3 the same or are they different? Thanks in advance.

Thank you for your time in making this, new switches ordered

Mine juat started doing this. My ect would not get 150 but the eot would get upto 169 nothing more. But as i would drive it the ect would drop down to 136. Im really confident that its the thernostat. Also the heater in cab wouldnt feel hot. Barwly warm with fan on high. My 6.0 powerstroke is an 06 with 180k miles. Any advice before doing the thermostat replacement?

What is order of switches New ones had different color and I couldn’t tell which ones are closed or open switches

I think i would have purchased a hole saw, it would be safer to use.

Oh, people took them when left on roadside.( House near highway).

Thank u for video. I have thrown out two microwave s almost new due to blown out fuses. Afraid MW having radiation waves.

Just changed fuel filter. Still low rpms. Rins rough

I have a question replaced the fuse 2 weeks ago just blew again what type of switches do I need the fuse I replaced is a 20 amp 125 volt fuse model IS FFMV162LSA

Thank you for the video - excellent alternative to the expensive permatrack . question - do you think these led pods are better than you typical single pixel 12mm one's ( which seem to be the standards ). also have you created a 3d printed bracket for the corner or maybe for the installation for them track to be more secure.

You are leaving things out skipping how do you take off the panel

I just took mine apart and the switches looked fine, sanded the switch contacts shiny again and degreased the switches with alcohol and it works again Thanks!

i FINALLY FOUND A VIDEO THAT EXPLAINS THE SWITCH DIFFERENCES ABOUT OPEN AND CLOSED. i LOOKED AT AT LEAST 6 OR 8 VIDEOS THANKS FOR THE COMPLETE VIDEO

What should I search up on Amazon.? Frigidaire door switches?

Also, how do you do power injection with these puck lights? It doesn’t look like they come with the extra cable for splicing power supply.

How did you do the corners for your tracks?

Awesome video

What's the part number for the seals

What is the formula to convert revs/mile to Decimal?

Didn’t show repacking wheel bearings.. very good lesson for your man.. did you use hub oil to fill hub? When you pulled axle, fluid poured out.. didn’t show replacing any.