Video

Hello buddy Have a good time and happiness This is a local camera. That is, when the camera is connected to the desired Wi-Fi, the other device must also be connected to the same Wi-Fi to see the images. And after entering IP in the browser, you can see the camera image. 😉

Hello buddy Have a good time and happiness I'm really sorry it's not clear in the video. Right in front of the esp8266 housing, you can see the golden lines, which are the internal (or on-board) antenna. I soldered the wire to the antenna on the board. 😉

Hello buddy Have a good time and happiness Thank you for the tips you said. You are right. I should have written these points in the video But in the description, I said that they should use high_power batteries for construction. I made this electric lighter according to the tips and important points, and after many tests and checks, I realized that the battery did not get hot at all. As a result, it is important to use high resistance wire. And I must say that with a lot of research, I realized that these types of batteries are made in such a way that they are compatible with these factors and tasks and can be used without any problems or risks.

Hello buddy Have a good time and happiness First of all, thank you for watching the video till the end. And I must say that I am really happy that this video helped you and that you were able to make your own monitor holder very easily. 😄👌 I also use the same holder that I made for my monitor. And I must say that this comment made me very happy and gave me a lot of energy to make future videos.🙏😉 thank you😄😉

Hello buddy Have a good time and happiness I am glad you asked this question. These types of boards include 3 types of antennas. The first type of surface antenna that has a shiny copper layer on the board. The second type is an sma socket for connecting different types of antennas. And the third type has both of these antennas. This board has a surface antenna, which is drawn as a shiny copper layer on the board. I soldered because there was no sma socket on the board 😉

@@Inventorsidea Got it.... As far as I know, this Nodemcu has an antenna already integrated into the board, and this limits it when finding distant wireless networks. And this scheme for soldering an external antenna, I confess that I didn't know about this trick. I thought that when soldering the external antenna, it would damage the Nodemcu board. Very interesting indeed. When it shows the welding of the antenna, the image is a little bad and there is a small cut in the video, so I tried to understand this scheme.

​@@Inventorsideabro can we put an sma adapter on the board?

Hello buddy Have a good time and happiness It's a good idea, but you shouldn't use the sma adapter. It is better to use small connectors like UFL, which are better and easier to solder and are also suitable for these boards. 😉

@Inventorsidea thank you very much brother can I used the antenna of our old router and can I attach two only just one brother??

Hello buddy Have a good time and happiness It's great that you saw the video and decided to make it. I'm really sorry you had problems with these libraries. The solution is to search and download any library in the Arduino software. But the better solution is to download these libraries from GitHub. Search their names on GitHub and download them. And add those libraries to the software from the Arduino libraries section.👌😉

Hello buddy Have a good time and happiness Thanks for watching the video till the end. In answer to your question, I must say that I do not know the range of the antenna! That is, by using different antennas, the range also changes. By using better and stronger antennas, its range will also increase.😉

Hello buddy Have a good time and happiness This esp8266 box was printed with a 3D printer, and I put the 3D file link in the description.😉

Hello buddy Have a good time and happiness Thanks for watching the video till the end. In your answer, I must say that in the utc field, you must enter the utc of your country so that the local time will be displayed to you. And this topic was also in the video. I did not understand what you mean by changing the direction of page rotation! Ask your question more clearly so that I can help you😉

@@Inventorsidea I have fixed it, thank you❤❤❤❤

Hello buddy Have a good time and happiness Thank you for watching the video till the end. Using the following site, you can download the appropriate file for your board. And if you have a problem, tell me so that we can solve it together.😉😉 deauther.com/docs/download

@@Inventorsidea hi, friend. I don't have that board, I only have esp32 c3 super mini and esp32 s3 zero. I see that it is not compatible

Hello buddy Have a good time and happiness I had not paid attention to this point. You are right and I must say that this code works on esp8266 boards and has better performance 😉

Hello buddy Have a good time and happiness Thank you for watching the video till the end.😉

Hello buddy Have a good time and happiness I made the split wire myself and did not buy it anywhere. You can make it very easily😉

@@Inventorsidea by any chance do you have a video that could show me what to do ? Thank you !

If you mean wire split, you must use female sockets for the number of outputs and connect all female sockets to one male socket. as simple as that I tried to explain in such a way that you understand completely😉😉

Try to remember the one hand rule though when you're working with voltages that could hurt you! Just some old guy advice 😉

Hello buddy Have a good time and happiness Thank you for watching the video till the end and reminding me of these tips and advice😉

Hello buddy Have a good time and happiness If you mean WIFI 5GHz, yes, you can do the same by upgrading this device. And if you mean the 5G network, I must say that this issue is a bit complicated. And for some reasons, it is considered a jammer, and it also cuts off people's access to emergency numbers, and it is considered a crime. But the circuit of this jammer network is 5G on the Internet, which has an educational aspect and a low range.

Hello buddy Have a good time and happiness The code language of this project is C++. Arduino programs are often written using the C++ language.

oh thank you me Friend !!!@@Inventorsidea

hello my friend Have a good time and happiness In the video, the schematic was shown and I put the codes for you. Tell me in which part you have a problem so that I can give you a complete explanation.😊😊

hello my friend Have a good time and happiness No. do not make a mistake. This is an 18650 battery that gives a voltage between 3.7 and 4.2 volts with each full charge. And that module was a power bank module that adds a little to the voltage and outputs 5 volts.😉😉

@@Inventorsideaah thanks :) makes much more sense now.

hello my friend Have a good time and happiness First of all, thank you for watching the video until the end. The wire I connected to the Raspberry Pi was to test the function and health of the oscilloscope. And I must say that in the video of the site that I introduced to download the software, this site is the provider of this program and a lot of efforts have been made in this field. Visit the provider's website and get all the answers and information you need.😉😉

​@@Inventorsidea And in description... No link. Why this video exist, if it hasn't any usefull information and you send people to site?

In this video, I tried to teach you the best and cheapest portable oscilloscope. But the code and file of this oscilloscope is the result of the efforts of a big team. And this portable has all the great features that I recommend to visit their website to learn about the best and great features of this oscilloscope. Because to introduce the capabilities of this oscilloscope, the video would be too long and has a separate video and discussion.😊

Hello buddy Have a good time and happiness Yes, it is very simple and very useful. And in response to your answer, I must say that I have not tested with other Raspberry Pis, so I would be happy if you do so and share your experience with us.😉😉

hello my friend Have a good time and happiness First of all, thank you for watching the video till the end. And I must say that in the video on the site that I introduced to download the software, the same site was the provider of this program and many efforts have been made in this field. Go to the provider's website and get all the answers to the questions and information you need😊😉

Hello my friend Have a good time and happiness First of all, thank you for watching the video till the end. And I must say that yes, it can have several entries. And in order to get important information and answers to your questions, in the video I introduced the site for downloading the software, this site is the provider of this program and a lot of efforts have been made in this field. Visit the provider's website and get all the answers and information you need😊😉

hello my friend good time In order to make a good security camera, due to the problems of the slowness of the software and the lack of clarity of the image, I mentioned the following below. 1. You must know the resolution of your camera and then enter the same resolution in the software. You can connect different ov cameras and... there are good quality cameras on the socket. 2. As long as the camera does not have the power and that resolution, you should not enter any resolution in the software. This slows down the software and image updates. 3. When you connect a high-resolution camera, you can increase the resolution in the software to get the highest quality image at normal speed. 4. You can use the antenna socket that is placed on the module and connect it to that antenna with a small conversion and increase its range, while don't forget to put the resistance on the external antenna pin first. I hope this explanation will solve your problem.