![Erich Forler](/img/default-banner.jpg)
- 163
- 29 402
Erich Forler
Canada
Registrace 21. 10. 2011
Math, computer science teacher, woodworker, and general nerd.
Thule Helium Platform XT vs Kuat NV Base 2.0
In-depth comparison review of Thule Helium Platform XT and Kuat NV Base 2.0 hitch bike racks.
zhlédnutí: 920
Video
Folding Nordic Ski Waxing Support
zhlédnutí 151Před 5 měsíci
Construct supports for Nordic/cross country (x-country) ski waxing that fold down to be more compact and can be mounted in different ways when being used.
Make a Mounting Bracket for a 7-Way RV Plug
zhlédnutí 180Před rokem
If you have a trailer hitch receiver and vehicle with no place to mount a 7-way plug for an RV trailer, this video shows a simple way to build one.
Snowblower Auger Locking Handle Repair
zhlédnutí 1,1KPřed rokem
How to repair an auger handle that isn't locking when the drive lever is engaged. On this Ariens snow blower, the auger handle should stay down if the handle that engages the wheel drive is also held down, but in this case, it wasn't locking. This video shows a quick solution to the problem
Repair Cracked Control Panel on Ariens Snowblower
zhlédnutí 71Před rokem
Rather than replacing the expensive control panel, aluminum bars are used to strengthen the panel around the crack, this is an economical DIY repair solves the problem without any welding.
Repair Broken Axels on Dishwasher Cutlery Tray
zhlédnutí 126Před rokem
The plastic axels that support the top cutlery drawer in some dishwashers such as the KitchenAid and Bosch may break over time. If you can't get the parts because they are discontinued, you may be able to use this method to repair them and make them as good as new.
Geometry Transformations - Rotation
zhlédnutí 4Před rokem
Lesson on geometry transformations specifically doing rotations about the origin which is a curriculum expectation for grade 8 Ontario curriculum.
Approximating Circumference of a Circle using triangles
zhlédnutí 79Před rokem
A step-by-step method of using progressively smaller circles to approximate the circumference of a circle.
Using 2D Drawings to make a 3D Model in SketchUp
zhlédnutí 42Před rokem
This is a lesson on using SketchUp for Schools to create a 3D model from 2D drawings of the top, front and side views of an object.
Solutions to Dilation questions 1-3.
zhlédnutí 12Před rokem
These are the solutions to the three questions in Dialation Questions.pdf. These solutions illustrate dilations using a positive whole number, fraction and negative whole number as a scale factor with a centre of dilation that is different from the origin.
Geometry Transformations - Reflection
zhlédnutí 8Před rokem
Lesson on geometry transformations specifically doing reflections in the x axis, y axis, y = -x, and other horizontal or vertical axes which is a curriculum expectation for grade 8 Ontario curriculum.
Geometry Transformations - Dilation
zhlédnutí 213Před rokem
Lesson on geometry transformations specifically doing dilations which is a curriculum expectation for grade 8 Ontario curriculum.
Geometry Transformations - Translation
zhlédnutí 12Před rokem
Lesson on geometry transformations specifically doing Translations which is a curriculum expectation for grade 8 Ontario curriculum.
Extracting, Manipulating and Graphing Survey Results
zhlédnutí 68Před rokem
After using Google Forms to collect survey data, you need to manipulate (or massage it) into different forms and then generate graphs in order to give your data more meaning. This is about turning your data into meaningful information.
Intro to Google Forms with Branching
zhlédnutí 31Před rokem
Using Google Forms for conducting a survey requires you to understand different question types. This video shows how to create multiple choice (radio buttons), check boxes (multi-select), drop-down (list box), Linear scale, and True/False (multiple choice). It also demonstrates how to ask respondents different questions depending on how they answered a question. This is commonly referred to as ...
Ski Wax-O-Matic L3 - Third generation DIY Nordic ski waxing stand.
zhlédnutí 782Před rokem
Ski Wax-O-Matic L3 - Third generation DIY Nordic ski waxing stand.
Nordic Ski Waxing Stand - Ski-Wax-O-Matic 1.1
zhlédnutí 648Před rokem
Nordic Ski Waxing Stand - Ski-Wax-O-Matic 1.1
Inequalities - Understanding multiplying both sides by negative 1
zhlédnutí 6Před rokem
Inequalities - Understanding multiplying both sides by negative 1
List Retrieval - Getting items from a list using a counter
zhlédnutí 18Před rokem
List Retrieval - Getting items from a list using a counter
List Retrieval 2 - Getting two related list items
zhlédnutí 24Před rokem
List Retrieval 2 - Getting two related list items
5 Step Process for Finding the General Term of a Linear Series
zhlédnutí 67Před rokem
5 Step Process for Finding the General Term of a Linear Series
Subtracting one Shape from Another in SketchUp
zhlédnutí 216Před rokem
Subtracting one Shape from Another in SketchUp
Simplifying Algebraic Expressions Examples
zhlédnutí 7Před rokem
Simplifying Algebraic Expressions Examples
Introduction to Flowcharting using Diagrams.net (formerly draw.io)
zhlédnutí 58Před rokem
Introduction to Flowcharting using Diagrams.net (formerly draw.io)
Great Build Eric! Any thoughts on how you might adapt this to a touring pin binding setup? Cheers
I've got another video I'm working on which shows the build for a clamp which clamps the sides of the skis which can accommodate different widths of skis regardless of the binding. It can theoretically also accommodate a downhill ski as well. Not sure when I'll get that video released so subscribe and you'll see it when it appears.
Thanks I’ll keep my eye out
Thank you this is exactly the video I been looking for to DIY my own bracket Thank you so much for posting this video I am going to copy your idea to make my own
Nice job!
Great fix, Thank you!
Glad to hear it was helpful.
Thank you for this video! My eight year old 28" Arien Deluxe just suffered this same issue. Had worked perfect up until yesterday and stopped. Did the bit of filing ad it's working once again...thanks to your video!
Glad it helped!
I heard a snowblower assembler for a big box store say that this was an Ariens recommended fix. Thanks (I used this solution to fix our Deluxe 24)
Glad to hear it was helpful for you.
Can you share how you removed the handle? I have a similar faucet and can’t seem to figure out how to remove the handle. There doesn’t seem to be a set screw.
Hi Ben, If my memory serves me, there was a small plug underneath the handle and when you remove that, I think there was an Allen key (hex head) set screw that had to be loosened.
Promo'SM
Somehow my comment got deleted. I'll give it one more shot without the link to the sketchup file in case that's flagging it. I've just about finished my build of this. Before I started I built a simple sketchup plan to help me think through the cuts. You can message me for those if interested. Thanks for taking the time to put this together and include many of the details. A few of the challenges I ran into: 1. I've got backcountry skis as well as kid's skis. I had to widen the base board to make this work (not reflected in the sketchup files) 2. the kids skis will be tricky due to their shortness, so I may need to find a solution to better stabilize them. For now it might just work well enough 3. finding the right hardware for the skis to attach to as well as some of the wider screws. I measured nnn bindings need a .15" metal rod, nnn-bc need about .18". The good news if you can aim for the lower size and it should hold for both. However, I couldn't find anything in this size at the hardware store. I ended up buying a steel rod on ebay that was close enough. A better hardware store may have a threadless rod in the right size. I couldn't find nails that were long enough. I'm waiting for the finish to dry, but hopefully, I'll be able to play with this soon. Thanks again
That's awesome Kenyon. I'm glad you've been able to make use of my experiences to help you craft your own solution. It would be great to be able to share the sketchup file but I'm guessing you're correct that it's not something that CZcams wants linked from comments. I'm planning to set up a Web site for details eventually, but haven't done it yet. Once I get the running, we could put the link to the file there. How short are the kids skis? My stand adjusts enough for my family's shortest skis but none of them are very short. Are you using the T-Track or fixed bolts in the base? Either way, I've found that if I reverse the tip and tail supports, they can support a shorter ski. The only problem is that the tip's curve isn't supported that way. I appreciate the measurements on the different binding needs. All my bindings clamp on the same diameter rod, so I know what I have to do to accommodate different skis. I've just been getting the right size nails from my accumulated inventory to fit but I'll spend some time thinking about a more reliable source. I've been investigating a method for clamping the ski into position rather than using the binding for holding the ski in place. I'll do a video of that if I get it working well. Ski season is just about over here (despite the blizzard that blew in tonight) but I'm hoping to continue with some design improvements over the next couple of months.
@@ErichForler The kids skis are around 110-130. I'm using the fixed bolts. I could probably shorten the sliding base pieces to get a little more room, but it works well enough as it is. I played with some ideas for clamping the skis without using the binding, but gave up for now. The binding shapes are different enough and it's tough to get a good hold without starting to overlap the ski base. I think it's possible, but I lost interest :). For now, I'm not using my downhill skis so the motivation's lower. With projects like this, I'm always appreciative of the few decent hardware stores left. Trying to find bolts at the big box ones is so frustrating. I'm finally investing in a wall-mounted nut/bold thread checker so I just order exact parts online. Thanks again for this build; it's a cool piece to have mounted on the wall for people to guess at :).
Next time, pour à mixture of hot water and vinegar and wait an hour. It works
Interesting thought. I'm not sure how well the water and vinegar would get into the thread but it's worth a try next time.
Great build! I'd like to just buy one of the stands you've moved on from 😉
They've all found homes so far but I'll eventually have a surplus.
Any thoughts for those of us of the 3-pin variety?
That's a tough one. Honestly, I would suggest upgrading the bindings on your skis. If you're set on staying retro, I guess you would have to fashion a piece of wood to fit the three pin binding and then you could probably use a similar method to tighten it down. Finding some used bindings would definitely be less work but of course then you need new boots as well.
LIKE 👍 👍 👍 👍 👍 🤩 🤩 🤩 🤩 💞 💞 💞
Hi guys! I love your ideas! Would it be possible to get plans for both models, the one kept for you and the one as a gift? Regards
HI Yvan, glad you liked the video. The first two I built were the same. I've built a couple more this year that are variations on the original design and I'll be releasing those videos soon so like and subscribe and you'll get notification when they're released. I don't have plans for these. They are mostly ad-hoc. Maybe once I settle on a final design I'll think about making a formal plan to share. Until then, the end of the video shows the key measurements.
can you send circuit diagram
There is a diagram at mr.forler.ca/component/content/article/33-blog-hands-on-tech/134-raspberry-pi-with-temperature-and-moisture-sensor?Itemid=101
Wow, looks awesome! I'm so happy that my video/design was useful for your build! The dado cuts are so neat.
Brilliant!
The link causes a 404 error.
Sorry about that. You can find it here: mr.forler.ca/component/content/article/33-blog-hands-on-tech/134-raspberry-pi-with-temperature-and-moisture-sensor?Itemid=101
This is great. Thanks a lot.
Very very good, native teacher, congratulations.
Link in description is not working
Fixed now.
hi, lovely information would love some examples
Hello, it gives me an error in the print final, Help me!!!
Hi do you still teach at D’Arcy McGee?
Very helpful
Very helpful thank you!
Are there no resistors needed? I have found some other guides that use HY SRF04 and they use resistors.
same question here - I believe resistors are needed, or a logic level converter if you have one
Late answer... But the sensor needs 5Vdc if I'm correct and the Rpi can't handle 5v directly to the I/O of the pi, so you'll need a voltage divider U=Uin+ R2/(R1+R2). Keep the idle voltage below 3.3v and you should be ok.