Video

can't go wrong with ca hinges.😀

I will say it again why spend the time and money on a nice scale model as this one is and fit a two-stroke engine does not make sense.

4 stroke engine in this models!!?

I needed this in 1980 when I first attempted building. I had the RCM flight training Handbook 1 & 2 and Al's Hobby shop, Elmhurst ,IL

what is the difference in weight between oratex and regular ultracote?

Great Video....but LOWER the music...a lot

the STAB?????? really???? cant finish words????

Fantastic video and very well explained and very helpful. Thanks for sharing.

Hi very nice video my question is if I’d like to apply PolyBruch with spray gun may i use directly from the can or i should use thinner Thank you

Do you have the rest of the build that could be posted? Thanks

The Fokker scourge lives on!

Very good information thank you lots

Love the air wrench sounds when fast forwarding!

isn't oratex Ultracote?

Great tutorial. The music in the background is not necessary, just saying.

I love the instructions! However, I think you need a better microphone and maybe some more light and close-up video and high-resolution, the second video was out of focus.

How thick is the wood?

This was recorded 6 years ago. I was "in" the class with Chad. I learned a lot and still have my XL.

@Balsa USA Airplanes, Will there bee a Week 1 class posted?

A shop vacuum is pretty handy to get chunks out, and also, outside the part, on the print, and all the other loose Debris...

Went on useless Balsa USA website, nothing but a countdown timer and the person chatting seemed to be a retard or something. Maybe it was a retarded AI, I don't know, but they lost a sale. So HA HA on them!

No matter what the Grain is doing. If you use windex on the outside of the curve, it will fold over for you. Ready to glue, really nice....

I use a stone wheel on my full-size planes and the little one. It is very sharp!!

The best cover you could use for your plans is a plastic thin film. The roll at joann fabricks, in the upholstery section. It is strong, thin, and (very clean like glass), and inexpensive. C a glue and regular glue like apoxy does not stick to it.

What melting temp does the solder need to be?

Dang, that music over and over and over and over again

The copper wire should have been cleaned after touching it with fingers, then flux applied.

Where is the video for installing hinges?

Great instructional video. Thx

What size engine did you take out and what size motor did you replace it with?

What tool is being used to cut the cable so neatly?

Ready to use the BUSA nicopress, turnbuckles and thimbles on my H9 1/4 DVII. Already used on pull pull rudder. Nice. Brand X plane. Sorry. Really wanted to learn best way to install turnbuckles. Ahhhh, a short cable run on one end. OK.

Gnome radial?

which engine? would zenoah 38 work

wow

Achtung, der Sturz könnte zu viel sein wenn das Flugzeug auf dem Heckrad steht und per Augenmass gemessen wird.

The Box is 3.5 inches off the mark here. Way too far back.

sounds like hes saying sodder,

How many flights / charges do you usually do before replacing those batteries?

Where can I buy that kit?

Great series- If I may offer one correction! The sheeting on the wing center section has the grain in the balsa going leading edge to trailing edge. The sheeting should go span wise .

👊👊😊😊

When stories the videos for the Cub gonna be out

Super vidéo 😊 c est très intéressant 👍merci

Another great how to video by Chad.

Great video, bring Chad back!

Great video, the iron does a great job at that size, could you use a small blow torch as well?

More of this please!