- 16
- 45 357
Seth Danenberg
Registrace 23. 10. 2020
Printing and Promotional Swag from your friend seth@iprintink.net
Removing damper manifold from Epson 9900 or 7900, clearing dampers without removing
Needs
Long Phillips head screw driver preferably magnetic
Send nozzle check to printer
When print head moves out open front cover
The Printhead will freeze in place
In plug printer
Remove two screws holding black cover
Remove 5 screws holding manifold to print head
Slide out carefully
To remove print head
Once manifold is out
Remove 3 screws and unplug 4 ribbon cables
Long Phillips head screw driver preferably magnetic
Send nozzle check to printer
When print head moves out open front cover
The Printhead will freeze in place
In plug printer
Remove two screws holding black cover
Remove 5 screws holding manifold to print head
Slide out carefully
To remove print head
Once manifold is out
Remove 3 screws and unplug 4 ribbon cables
zhlédnutí: 1 046
Video
Cadlink Digital Factory Basic Setup Epson 4900
zhlédnutí 446Před rokem
Follow the on screen instructions to get your Epson 4900 started today
Setting up Epson 4800 for DTF for the first time
zhlédnutí 6KPřed rokem
See our video on cadlink setup and powder shaker setup on our channel
Cadlink Digital Factory R3000 Basic Setup
zhlédnutí 302Před rokem
Basic cadlink settings for Epson r3000
How to get Started with DTF Direct to Film Powder Shaker
zhlédnutí 608Před rokem
What you need Powder shaker and printer, obviously Direct to film roll not sheets 1 old 3 inch core roll Roughly 7 feet of old printed material or 7 feet of your first roll You’ll need an old roll and film to “thread” the powder shaker backwards from the end back to the printer
Epson 1400 1430 1390 l1800 Printhead Change or clean
zhlédnutí 6KPřed 2 lety
For Epson cartridge based system Press ink button When in the load cart position unplug For tank based l1800 type send nozzle check to printer when the print head first moves to the left pull plug out in the middle of print Remove plastic door all together Look for two plastic clips on print head right side, rotate door up out of the way of ribbon cables Hook behind cartridge bank connector and...
Heat Press Transfer Placement Direct to Film
zhlédnutí 54Před 2 lety
For front left chest always center your art where the collar seam and shoulder seam meet Use a guide as often as possible An old Rule of thumb is to place the top of the artwork 3 fingers below the bottom of the collar of the shirt… however everyone has very different sized fingers so this is not a great rule
Epson 1430 1400 l1800 1390 Basic Cadlink Setup
zhlédnutí 3,9KPřed 2 lety
Epson 1430 1400 l1800 1390 Basic Cadlink Setup
Epson 4800 Print head removal and frame cleaning
zhlédnutí 7KPřed 2 lety
Epson 4800 Print head removal and frame cleaning
Does this work for the stylus 1410?
question do you need a special software to print out stf files or Adobe will work?
I don't have the solution to soak the print head in. what else can I use to soak it in?
Simple green and distilled water 50/50
I cant find my production plugin option
Is there a way I can get in touch with you
Sure what do you need help with
I hope you see this Setting up for the first time. I just need clarification. I use the l1800 option for my artisan 1430?
Yes the l1800 queue will work for the 1430
Please what printhead does the printer use?
www.ebay.com/itm/114236984504?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=KozVoDVuSL2&sssrc=4429486&ssuid=ezDN_j7CRke&var=&widget_ver=artemis&media=COPY
Is this the same settings using the 4900 to use a 4000 like the one your setting up in your other video
The settings on a 48xx are somewhat similar but that is a 8 color while this is a 10 color, so there are some additional steps
I would like to convert my Epson 1430 from an all-black to a DTF. Do you have a video on this?
czcams.com/video/i1DENssoVcw/video.html
Good info. What type of film works best in this printer
I have a stylus photo 1390, where do I buy the print head and what print head do I need to get ?
www.walmart.com/ip/Replacement-Printhead-F173030-For-e-pson-epson-1390-1400-1410-1430-1500W/5084467031?wmlspartner=wlpa&selectedSellerId=101016856
bad work
Hi there! these videos are very helpful, as I've just inherrited an epson pro 4880. Although, I am missing the CD for the software program, and my computer doesnt seem to be able to read the files that I download fron Epson Support that are suppose to be the software. I only get a bunch of folders and small files. Do you know how to manage to download the software without a CD?
www.epson.eu/en_EU/support/sc/epson-stylus-pro-4880/s/s696 download the one labeled drivers
Thank you for making this process easy
good video, Seth i could only find 6 cartrdiges of DTF . do use the other two and purcahse white seperately ?
What do you mean only 6 cartridges You can use as little as 6 but you should have 8 carts
@@sethdanenberg4978 thanks for the reply when i searched i only found the 6 cartridge pack ..
@@sethdanenberg4978 Hi Don, my last reply didnt post do you have a product package/kit to convert the printer that you suggest? thank you
@@actionnew yes, you’ll need carts $120 Resetter $20 1 liter white $75 250 ml cmyk $25 ea 2 pounds powder $35 13 inch roll $120 Cleaning kit $20 Waste tank replacement chips $10
I just cleaned mines and its working great. I really appreciate the video. Great job !!!
Awesome so happy it helped someone
When I print my white came out like a grayish Blue and my red came out like a pink. I don’t know what I’m doing wrong it’s my first time with dtf or any of the software I’m using digital factory v11
check your ink order, make sure any old ink is flushed from the ink lines, it cna take up to 3 power cleans to force all old ink out, print a nozzle check
Hi. Where do I purchase your maintenance ships and why you prefer the 4800 to the 4900. I have a used 4900 I want to convert but don’t want to spend money on the refillable cartridges unless I’m sure that it will work ?
The 4900 prints faster and higher quality, however you will be replacing the capping station every 6-13 months. The 4900 is also just generally more sensitive and less reliable. I have some maintenance chips for sale if you need some
Your video helped me so much!! I have a 9800 and finally got it to work tonight after watching your video! I do have a question, my white is at 90, but isn’t laying enough down, what should I do? RIP 10 software…
How does the nozzle check look? Are you shaking the white ink regularly or has it been sitting? 90 is very high, usually 70 is plenty. What type of ink is it
Everything looks great on nozzle check, I just had some ink that came with my printer… so it could be the ink. What do you recommend? Just got this printer and converted it last might
@@christineketcherside2133can you send me acreen shots of your settings?
@@sethdanenberg4978 yes sir
It won’t let me upload pics on here
Hello, can you tell me please is the epson sc pro 4000 can be converted to DTF? and what program(RIP,SOFTWARE) can I use to print on mac or windows? thanks
I am not 100% sure but I believe the 4000 can be sued with the newer version of acrorip. I do not use that software I use cadlink digital factory. Both software programs are only available for windows
Hi Seth, which shaker are you using? Is that a 13"?
Hi. Thank you for the video and the information. I owne 4800 epson stylus pro i want to convert it for tdf. What software can i use for it.? Thank you and congratulations
Epson 4800 works great on Cadlink Digital Factory Direct to Film Edition
@@sethdanenberg4978 thank you for your replay. I will download and try it. Is it free or need a licence ?
Ur video quality sucks ass
Any reason for pulling vs pushing the ink?
Pushing is very effective for clearing tough clogs but it is highly likely it will delaminate the print head and render is garbage. Pulling is slower but safer
Hello, for L1800 There's no option for me to change color order. Can anybody help?
Set ink order is under the queue tab up top, you may need to load the v2 driver
That's not an Epson 4800 printer.
That’s an epson stylus pro 4800
@@sethdanenberg4978 I need to know where the Print head on an ET-4800 is not a Sylus.4800.
@@magiwalt I dont sell those but a quick google search shows something like, czcams.com/video/XkiUcoywbdE/video.html&pp=ygUWZXBzb24gZXQ0ODAwIHByaW50aGVhZA%3D%3D
@@magiwaltit says it is an Epson et 4800…. Just click bait here, so frustrating
Hi , we own a 4900 unit , 1 weeks ago our capping station was broke and i replaced the dampers also , from that day i cant get good white nozzle check , any idea what can be the problem?
Do you get nozzles firing at all? Do you have the adjustment software?
@@sethdanenberg4978 Hi , before i replaced the dampers and the whole capping station everything worked fine , now when i do a cleaning i can see on nozzle test lines from every white channels not too much but after an ink charge or something similar all white missing , i installed external waste tank also and when the white is comig from tubes its like 90% air and 10% ink i dont know if this is normal
@@printedluxecapping station is clean, did you water fall the printhead while you were replacing the dampers
@@sethdanenberg4978 no i never waterfalled the head because on my previous printer i fried my head unfortunatelly 😆 but the nozzles are 100% its not clogged because yesterday i get a nozzlecheck 2 whites was 100 % and the other 2 white was like 70% on nozzle check , but after a clean everything missed from whites
@@printedluxe sounds like you need to manually clean the capping station and print head, then maybe do an initial fill
Hello Seth, is this printer model DTF from (original) ? or is it converted to DTF ? i found a 2nd hand Epson 4800 for DTF, owner says it is working perfect, and asking 2400 euros, what is your recommendation? pls 🙏👍
how do you stretch out your job image make it bigger to cover the whole 13x19 sheet
I'm trying to get cadlink setup with my 1390 roll feeder, any suggestions on settings for this.
My printer is not printing the white back layer? Do i set my ink order with white in the last 2 blocks even if my white ink is not in those tanks? My white ink is in the middle? But the ink order is just the order it prints out correct?
when you print a nozzle check does the white show up? Is the RIP set on underbase white and what is your white percentage?
No it doesn't. I just figured out my mom never set the white up. So I did that and I think damper might be damaged so I ordered another one. Was just trying to make sure I'm doing stuff right. So when you rip that's telling it to print the white layer?
@@crystalgrey9655 exactly, the RIP does alot more than just that but you will be controlling your white and how much you use via the RIP
Hello when I get to the part at 3:02 I see I don’t have those options. Can you please help me with that if you don’t mind thank you
top menu tools options make sure show advanced settings is checked
I have a Epson xp1500 with chipless tanks and software. Then I installed cad link. First it wouldn’t print until I did several head cleanings every day now it is printing yellow where red should be and light yellow where white should be. No white backing the hole thing….any ideas on what I did wrong?
Color order is not set to match the actual ink carts, are you using the the basic xp15000 or the v2 xp15000 in cadlink?
Hi, one more question , how i can flush out the old epson ink from the 4900? ( the service program doesnt want to communicate with printer ... )
you will need the service program, what step are you stuck on? you'll need to use the ink charge tool. other wise youll need to do about a dozen power cleans
@@sethdanenberg4978 when i hit on the adjustment (invidual ) window i got an error message "the setup was failed , may the board is damaged . "
Thank you so much for taking the time and for sharing this with us. I really appreciate it. I had done this before .. well about 7 years ago and forgot the steps.. I think I burned the decoder (according to an online tech) but I have another printer which I decided to swap their printheads .. so yeah .. your video is very helpful. Thank you.
What did it do to make you think the decoder was burned
@@sethdanenberg4978 Ok.. so I have the continuous ink system.. one of the lines broke and leaked ink .. the printer would power on and the cartridges compartment would go back and forth just like every time I turn it on.. but then when it get to the ready position, the ink light would come on and stay solid lit. I did everything I could think of .. cleaned, wiped did manual ink printhead cleaning with a syringe pump and even replaced the cartridges but nothing worked. when I explained it to the tech..she said the ink must've gotten to the connectors and the printhead has to be replaced. I opened it last night after watching your video and BINGO! she was right .. connectors strips were soaked. I do have another identical printer which I am in the process of swapping parts and hopefully that works. will let you know how it goes though.
@@sethdanenberg4978 So, This is my second reply as an update.. like I had mentioned before .. the flexible cable connection was soaked so I replaced the whole thing with one from an identical printer I had sitting there for parts, but when I did .. the printer wouldn't even come on!! but when I put the old printhead when is supposed to be burnt.. it powers up but I get the solid red ink light. thats weird .. I swapped them a few times same results .. I was really disappointed and dont know why it wont turn on.. I put both printers aside and now I'm using my old Artisan 1430. Please let me know if you have any idea . Thank you.
@@yemarican That print is most likely no good it may have fried the main board on the printer. When you turn the printer on listen closly to the back of the printer for a very quiet beeping noise
Is this printer really prints really slow?
You can realistically expect 6-9 13x19 sheets per hour If you run the fastest mode at a lower quality maybe 10 sheets 13x19 per hour
@@sethdanenberg4978 6-9 a hour for 13z19 not bad that's a average of 6 mins for 13x19 but I'm just going to 11x17
hi, i can't get passed the device package search when i initially start the program
What happens when you click Devices Manage devices Plus symbol yo add printer
I am trying out the 15 days free trail but I need an activation code where do I get that
youll need to pay for the software to get an activation code, where did you down load the trial
@@sethdanenberg4978 I got through
How its working your 4900? we looking to add for our shop, because we dont have luck with 3800
the 4900 is huge upgrade from the 3800, night and day for converted printer the 4800.4880 is still probably the best bet as it is easier to maintain but the 4900 prints faster and higher quality
@@sethdanenberg4978 Thank you so much for your quick answer , im looked also for 4880 but i doesnt find any good deal on it .. thats why im looking for 4900 , but really thanks for your help
Hello witch cadlink to get for desktop
hi i have been watching your videos i just purchased a used 4880 it was ran with reg ink do u recommend flushing system 1st
You don’t need to However if you don’t flush it with cleaning fluid it will take longer for the white ink to come out clean. In hurry I’ve done it both ways
Bro u have a video for the 4800 on Acrorip 9? I’m have trouble getting that white under base
Unfortunately no, I found cadlink to be so much better I gave up on acrorip. I know some people have good experiences with it
@@sethdanenberg4978 thanks I was up all night and I found an Acrorip that works thanks tho
My cadlink wont connect to printer
Obvious stuff, printer cable is plugged, download OEM Epson printer driver, make sure printer is connected to computer If the printer is working with the computer but not with cadlink ***on the top let area of the menu click, Queue in the drop down menu click, Manage Queues your printer should appear in the list there next to your printer queue name, make sure the printer is selected under printer, click the drop down under "port" make sure that selection matches your printer listed in your computers printer list
@@sethdanenberg4978 Hi, when I get port selection it says “NULL” and “no port selection” and I cannot select a port.
Hi what ,my white channel ( L magenta) looks like jammed with an old regular ink , i try to.make poewr cleaning for 3 times ,all the other chanels are good except that one , any solution to get the line clear ? And what do you think about the chip decoder ? If there is one pin coming out of the cartridge reader with the decoder work? Is that easy to fix the pin that came out ? Thank you
Replacing pin connectors in the ink bay is relatively easy, the chip decoders also work great. For the ink, is there air in the ink line? Or does it appear as solid as the other ink lines that are flowing
What RIP software do you use for the 4880?
Cadlink digital factory
Hey I have epson artisan 1430 and I can’t get it to print it was printing yellow at first now it won’t print anything
Hows the nozzle check look?
How do you convert it to print dtf
Remove exit wheels Build exit board You’ll need refillable ink carts Chip resetter 1 liter white 250 ml ea cmyk 1 roll film 2 pounds powder Fill carts Right side all white left side match standard color code Remove ink manifold on print head With a syringe suction all oem ink out while pulling new ink in Download cadlink Follow the setup video Get printing
Hello! I have been using one of these for a few months and had to replace a relay switch. I’m now having problems with temperature etc. I have scoured the internet searching for info but no luck. Any tips? Have you had to repair yours. I would be happy to pay for any help you could give. :)
HEY DO YOU TAKE THE ROLLERS OFF IT?
Yes, do you need help taking them off?
IS IT AS EASY AS CONVERTING L1800??
I CONVERTED A 1430 NOW CONVERTING A 4800 SO I NEED TO KNOW IF I CAN TAKE THE ROLLERS OFF LIKE I DID THE 1430
@@faust4658 the rolls are easier to take than on the l1800-1430 You just unscrew center assemblies
HEY WHATS THE INK CHNNEL FOR THE 4800 ?? KCMYWWWW???
My machine is saying wrong ink cartridge. I have done everything I have read. Can you help me
Have you tried “shimming” the cart Have you tried replacing the chip Have you tried using a different cartridge?