Video

😂 just buy a single shotgun for 99 bucks

are you died or alive

You really have some good videos. Thanks for all you do.

I have a brand new colt 1860 snub nose and I absolutely cannot get the barrel off, any ideas?

WHAT IS CAUSING THE LOCK UP ???

Fkn vac hose rotted out. Whole day to replace 5 dollar hose

At 100 yards need to put your sight up one notch to the 100 mark the backsight

You may be joking but masking tape detritus covered in paint is a nightmare & this is a filthy solutiom 😂

Just purchased a Pa. Pellet flintlock rifle and this video is very helpful.

czcams.com/video/eSBB_9RhaTg/video.html

Well done, sir. I’m replacing my hose as we speak.

I like the stare head much better than a Phillips head though. Put some good penetrating oil on it, wait a few minutes then whack it with a hammer a few times to "shock" it. Q lot if times it works good

Nice job. Is that just a piece of plastic you made and fitted between the two pieces of wood?

That’s really cool. Much more interesting than bolting on a piece of plastic

That guard is primarily to duct cooling air around the fins. I say that so no one will remove it, engine cam over heat and cause serious problems

The valve seats are steel. Save that clutch if you can! They are expensive.

Try a hand impact driver on the flywheel. I've had good luck using them. It's a 3/8 drive, but comes with screw bits. I put a socket on them. A few good blows with a bigger hammer and it does good

GREAT VIDEO

Great stuff Hovey...you are my favorite new celebrity...i shoot a variety of old stuff too...my fav is a traditions muzzleloader with a fast twist...great for whitetails and squirrel (loaded down) its a short little carbine and comes up quick...like it.... thanks for great content and your perspective.. Everything I have is old too

Thanks for sharing.

Plastic derived from these coat hangers had a lower melting point, lower flash point, and was much more brittle that the plastic derived from the lawnmower operating nobs. This would be best used for repairs on static, non-stressed objects. Under vibrational stress it may crack when I operate the lawnmower and fall out. Time will tell.

I've taken thin walled pvc, get it pretty warm and you can lay it down on object to be repaired and mold it into shape. Then scribe area you need, cut it out then glass it in from rear, fill in the seen side with epoxy, sand, paint and go

Love learning more from you on so many topics. Thank you for this

Nice work Hovey. I was able to bag a turkey this year using an original muzzle loading shotgun. Your videos and book Extreme Muzzleloading were a prime motivator for this endeavor. As you have said just get em close enough and those old guns without a choke work just fine. Thanks for passing on some of your knowledge.

I've taken a torch to mine while it was still molten lead in it and still on and twisted the plunger. It works most of the time for me

I’m proud to see someone else with my luck 🍀 🤣🤣not laughing at you just with you

The dipper is made by Lyman, not Lee.

Tires on .y trailer gove it up last week.

Hi Hovey, You are indeed the biggest (DIY) Do It Yourself creator on CZcams!

Sir I do not care what anyone says, you can not beat a king cab ford ranger that is in good condition. I have pretty much the same truck mine is a ford ranger edge with the 3.0 v6 and it gets me everywhere I need to go for hunting, fishing, and everything else.

Be glad it's not kudzu!!

Very nice to see you again, Mr. Smith

Pop rivets, solder gun with a flat tip, melted black tie as filler. Also if you had some extra hood plastic, add MEK and make a paste for bonding.

Way more meticulous than I would have been! I'd just cut a cardboard box and strap it on...Interesting to see how it will hold up to vibration. Email if you need any help around the house, my boy and I are free most Sundays.

Maybe not a brand new look but really 100% functional, using things available and a lot of creativity!

Duct tape and baling wire - a country boys fix all.

Informative, thank you

How did you get the display

What size belt did you install? I have the same mower, but the belt the deaer sold me won't fit?

I’ve had a Mrs Tea since it came out, practically new, used only 3 times to make tea and always wonder if I can use it to make me a cup of coffee, it looks like YES..thank you for letting me know. Great video, blessings

Good luck, Father ❤❤

Don't feel bad hovey all I got this year was a Jake and only cause him and his buddy beat up my gobbler that was almost to my decoys and then they beat up my strutter decoy so I got a lil bit mad and then got even lol

There is also a little finch size bird called a Yellow Finch and the male of the species is a vibrant yellow.

Thanks Mr Hovey Smith for all your teachings on turkey hunting. I applied some of your techniques and got me a gobbler on the last day of the NC turkey season with a 11in beard, 1 1/4in spurs and it'll certainly be good table fare here soon. Great videos and God bless!!🦃🦃

GOOD VIDEO. TY

I love you Hovey Smith

Are you still alive?

Very informative Mr Smith

It's not designed for a 12 gauge shotgun shell the 12 gauge adapters for a 12 gauge flare gun shell

I have taken doe with my 45 Long Colt flare gun adapter at 14 yd from my blind so it does work good🇺🇸👍👍💯🇺🇸