Video

Baby oil - cheap and cheerful - clean the brush every time after use and lube the needle on a cloth - job's a good un.

Using PVA for that is nuts - super glue gels are the way to go!

He did not show the placement of the safety device which is mandated by law to stop a child from strangulation, very disapointed.

Wow this must be one of earliest miniature painting tutorials on CZcams. Still useful even for today. Very nice.

Why do you fit the material rolling down from the outside edge? And not have it rolling off the rear edge thereby making a seal to the wall or window...which cuts the light out!! Which is why they are called BLINDS. ROLLING OFF the outer edge leaves a 40mm gap between surfaces and blind and lets the light in.

Good vid. However would have liked to know where 32mm cut off measurement came from

Fake news, stolen elections have consequences.

Was there this weekend

Much much better than the Dunelm video. Thanks

Good to find this I haven't cut my blind but I just can't insert one of the plugs. After numerous attempts I noticed the metal hollow pole is not circular its more oval 🙈 No way I've done that as I don't have the hand strength to insert the plug let alone reshape metal. I'm wondering if the mallet might force a round peg into an oval hole or if its back to Dunelm

I have been looking everywhere for an explanation of what the crown cap was for and its use. I even search the airbrush's manufacturer and got nothing. Yours is the first video I came across with a good explanation.

That’s very well put together video. Thanks

Dead right about all screws that come like this.

Thank you very much. This is the exact tap i have bought for the kitchen with compression valves with traditional rubber washer instead of ceramic disc cartridges which don't last as long. This to replace a Pegler single lever one that lasted about 3 years?! Nice down to earth explanation. Nice to know i can do this myself. cheers.

A very helpful video showing every step in detail. Thank you.

I make this articulated

Fantastic super thank.

Thank you, very helpful.

I just started using Superlube this week and it's definitely got all the relevant bits sliding a little smoother!

Back here in 23 for the re-release lol

Love my skelis from mantic!

How did it end up performing?

Технолог украл идею у Аирфикс или Аирфикс украл идею у Технолога?

Superb video. Very easy to follow and slow and clear at every stage. Good tips on where to work (kitchen floor in his case), how to mark lines accurately, how to cut the fabric and the top and bottom rails etc. He speaks clearly and loud. Very good guide, hope I can do as well myself this afternoon.

Thanks, the measuring between brackets isn't clear in the poor paper instructions supplied, and your video tells me what I need to know. Tip, I always turn my hacksaw blade the wrong way around when cutting thin tubes as it then doesn't bite on the forward stroke if I don't have a junior hacksaw.

ive just ordered one tonight...used to be a florymodels discount on them but its gone now it seems

Just tried to fit a Dunelm blind following their instructions, didn't fit, too long. After searching the interweb found your vid, brilliant. Remeasured and recut ( what a faf( ) now all ok. Now for the next one. Thank you!

Great review pal. Going for the slightly bigger brother with the Silver bullet at £269. subbed!

Good job

Halfway through here and the issue is with all the equipment which I don't own such as spirit level, right angle ruler, large scissors, blade thing, hacksaw.. by the point I have bought all the extra DIY equipment I may as well pay someone to fit them for me.. I suppose that is why many people avoid DIY jobs. Not to mention the risk of fudging it up and having to buy a second set of blinds

hate these airbrushes buy a badger lot less fiddly

Thx for help great video

Thanks mate, worked a treat and thanks especially for all the invaluable tips about how to do a really professional job :)

Just got the blind from Dunelm, scratching my head jumped on You tube and you my friend made me realize how simple it was..Much Appreciated and all this time later we are still being helped by you...Big Thanks

Update! You gave me the confidence, and I did it! I didn't have to cut it either as it is a massive frame with a smaller window. Just added the 3.2 on. Thanks!

Thanks I just bought one of these today and the instructions are crap

Thanks! Even the Dunhelm video was unclear on all these steps. I didn't really understand why you had to do the 3.2 cm cut before this. Why isn't it just 3.2 shorter to start with? Fingers crossed I can't mess this one up.( last one was a failure).

To begin with, M 5 Stuart was never supplied to the Soviet Union under lend lease, so even if you put another dozen red stars (in fact Soviet tanks very rarely had red stars on them), it still has nothing to do with reality.

Very informative review. Your perspective on this airbrush was really cogent. I just ordered one!

Please come around to my house and fit my Dunelm blinds .....😂😂😂 what a nightmare if you don’t have the confidence or tools to do this yourself . Thank you for your video

May 2022 and still helping! Thanks for taking the time to do an in-depth video.

Excellent video of how to fit a Dunelm blind. Much better than Dunelms own

Thank you so much!

I wonder how much worth is this set now in 2022

Thank you for uploading this its going to help me to reposition and cut-down the dunelm roller blinds in my bathroom. The tip re the tape has been especially useful for me.💕

Rubbish mate couldn't see fuk all

How much and the phone number to contact the company. Thank you

Thanks for taking time to create and post this video.

traditional sign writer, been using brushes for years but about to explore the world of airbrushing, got an Iwata eclipse cs and just ordered one of these spray booths, hopefully arrives in few weeks. you reviews were brilliant. so how's it going, you still using it? is it still working good after aw these years ?

So much better than the instructional video that the sellers provide, they don't even show the cutting part!