Video

Where is the bypass intercooler valve located on a 2017 Buick Encore 1.4

Thanks for the video!

This fix was great and surprisingly easy. well done! However, my headlights are not working now. Every other light works. any ideas or suggestions. The fuse is fine too. thx

The Dog watching like he’s a devoted fan.

Thank you

Any idea of the part numbers for the belts on this thing? I have one and not even bobcat can seem to get the right v drive belt to me…

4 cylinder? Or 6 cylinder? Is the same location?

Thank you

Hey I know this is an old video but I appreciate the help I just hooked one up after watching you thanks

Very cool. That turned out great. Nice TJ!

Excellent idea!

I’m about to do this with my 06 TJ… and I’m terrified😳🙏🏻

Hey help me out if you will please . I bought a new use hatch from a junk yard for my 11 mariner and now I cant get the latch and the window latch to work . Should I just use the latch from the old one I already changed the window no luck. Hopefully you have a idea. Thanks

Was the shaft size for the clutch the same ?

I have replaced latch as instructed and plugged all in its place. Window pops open but new latch doesn't pop open as it should? Where else do I need to trace the issue? Thanks for the video! it helps a lot. detailed thoroughly!

Where did you get the fittings for the large filter?

Is this the same for a 2018 MKZ? I’m trying to replace that part but I can’t find exactly where it is.

I love this idea…..I have an 18’ round and want to create something similar. But flat🤷‍♀️🤦🏼‍♀️ I want two halves that come together lol I can picture it in my head. Think of a trampoline but not bouncy

How has it held up so far ?

2 of the 3 screws holding in the latch stripped . Any suggestions. I was using the T25 hex socket.

I saw another video where you can also hold the AC power and defrost at the same time for 30 seconds then it resets. Or The green plug you can see if you go further underneath that area he was working on. It’s like a fuse looking thing but it’s a connector “green” you can unclick it look to see if it’s in tacked then put it back in if it’s good. It will also work. I heard sometimes it works for about a yr then try to do the same thing over until that part you changed actually needs to be replaced. 😊

To release the hose from the valve just push on the tab on the opposite side you stuck the pick in and it pops right off.

This is a beyond shit car. My car is old (2002) but things are starting to break one after the other, first the sunroof broke right after opening it, a week ago I open my trunk and glass, both, and now both are broken. This car is falling apart and breaking and it’s extremely fucking convenient it’s happening right after my car got stolen by the fucking 13% accounting for 50% of X, and I just got this piece of shit.

I was in such a jam because I have to move and my trunk wasn’t opening. I actually have a shot at fixing this. You’re an absolute beast, keep up the good work brother

What if my fog light doesn’t turn off? I replaced the switch, turn switch and the only way it turns off is by removing the relay.

Most of the trucks look so real. The back ground brings a lot to the image Could you make a over sized yard stick for a photo shoot.

This was so helpful!

How do u get that out of the green thing broke off

I cant believe the shop quoted me $450...

Great video buddy...somethung went out this am on my 2009..Police car..Impala LT..3900 ENGINE...HOPE ITS WHAT U SAID...BUT THE ANTIFREEZE RAN OUR THE BOTTOM ON THE PASSENGER FRONT SIDE...JUST INSIDE THE PASS. FRONT TIRE AND JUST BELOW THE RESOURVOUR, WHERE I POURED IT IN

you probably don't get snow where this pool is?

Didn't show us how you got out of pool with no ladder in place!

Just changed mine today in 2015 Ram Bighorn. Message said right rear, it was 3rd light. Put in led, message cleared and light working (for now).

This video was very helpful. My code says the Canister Valve purge. I’m looking at Rock Auto for the part. My question is should I replace the just the canister or would it be better to replace the whole part? I’m leaning towards replacing the whole part so I won’t have to go back and do it again, but I want to make sure.

Thank you for this video my sister I law has the same truck Ford escape in the fucking thing you have to go all the way down and pull it up thank you for showing me how❤❤ my

What is the overall width now with the bagger installed?

Thank you so much for posting this it is so helpful!

I wish you would have video recorded the inside of where you removed the driveshaft.

Now, do I have to mess with my riming belt or anything, or can I just take it off. Before I looked on CZcams, I couldn't figure out why or where my coolant was leaking since I replaced my radiator.

How did you connect the coax to the wire hanging down from the opener? There is no input for the connector on the Craftsman unit. Chamberlain units have an input. Plase advise. Your CZcams is great. Thank you.

Great vid and good tip Sir. Also, nice tip of the hat to the Freeze Mizer!

2006 Pontiac Torrent SUV I Just replaced those bushings but still have a rattle on the Drivers Side and just found out that the Forward Bushing needs to be replaced they're the Press in type, I was told that you can use a C clamp to press them in.👍

I put in the new part and it is still blowing warm air what do I do next

Looks good

You have hyper flash mine had the same thing

This is 2017 2017 MKX blowing hot air out of air conditioner

Great demonstration helped me immensely thank you

Thanks man! Much appreciated!

Thanks, man!!! I think this fixed mine. The 3rd light was out (got pulled over) replaced it with a LED. Saw this video and swithed that light back to a regular bulb. My problem is fixed... So far. Nevermind, it came back on. Ram/Dodge really needs to fix this. It should be a recall or a class action suite against it. Too many people having the same problem. It's super annoying!

What’s the parts number?