Video

I need tools you need help me bro

Crank line karne wala jugaad kahan se milega

Mantappppp

عالی❤

Gotta say thanks for showing the proper way to do that repair, although that's not exactly easy, it's far better than just rethreading and stuffing a larger bolt in the hole, or using foreign material to take up the lost threads.

Sir, the figure shown, I hope you understood it. 1) heat prob. 2) in newly_built piston , air escaping from joint may not reach to top of the piston. 3) piston is to be replaced often. 4) cost. 5) as the time goes joint hole will be widen. It is major problem.where as in scroll it's not.

I want this cutter

Location po nyo boss..basag kc ang hub ng skygo ko paayus ko po sana

Wish I had done this. Although I was not going to use the head again due to corrosion, I wanted to see the extent of the corrosion up the sides or the seats so I used a chisel through the port to break them out, causing more damage.

Location

Location

how much po magpapagawa ako?

sir location?

Мастер,побольше бы таких людей

Bhai ap ka whatstapp number Kay ha

Still looking for an answer after 40 years. In motorcycle magazines in the 1980s. Performance shops would "weld the crankshafts" of Kawasakis and Suzukis. Their flagship KZ1100s and GS1100s had assembled crankshafts with roller bearings. Welding made them as strong as one-piece cranks from Honda and Yamaha. How the hell does someone get a weld into the deepest reaches of a crankshaft to make it one-piece??

Just a small weld on seat and flat chisel a piece of a wood paint stick under chisel seat will shatter and not leave a single mark on head.

First smart comment I have seen since I have seen since looking at these posts!

Big Master Big beautiful big lovely big best big video app ka mobile number ka ha Lahore Pakistan 18.05.2024

Nice works ❤

Sir Plz culch hozing size Plz guide me .. watinar

bạn rất giỏi !

Well done

Bohat he acha kam krtay ho ap Plz apne location to share kr dy

Bhai apny value set Handel ki video nai bheji

Polish paper video bnaaoo

Kitne number ka polish paper

Cylinder polish paper konsa use karte ho

Do minute ka khel he mare samne 😅

Auto mech here. I never realized that this is the way small engine crank& rod was held together and balanced. Might be stupid question but what keeps crank and rod from becoming unbalanced while operating? Jus press fit? Yikes.

boss location nyo po?

Aaa Sab Karney Ki Koy Jarurat Nehey Hey 😂 Company Khutdh Karkey Quriyar Kar Dety Hey Falltu Ki Time West Meney Parches Kiya Thaa To Tab Samaj Aaya Genuine Part Khariley To Asab Nehey Karna Parta Hey😂

Me ne aap ki video dekhi bhut acha kam hai phir mene mogal auto par dekha same jo aap ne banaya roker cuter lekin aap shoker botom cuter banane ki video banay to aur madad ho jayngi jazakallha

COmpany price

It would be nice if you showed the drill bit size and the correct tap size for the hole.

helikoil daha iyi

Ye kam kaha hota h Crank ka bro

Pls explain both tap size?

What are both tap size?

Dont let all of that horse power go to your head

😮 o top 👍

looking for die tap that very reliable.. which brand is it?

Wah bhai mashallah Maza aa gaya apki mehnat dek kar Logo ko bhonkny doo bhai. Bore 100% sai hai

Hi

Locatio po?

what is the diameter of that crankshaft to achieve the M12x1.25

It is excellent working broo

Cylinder Ko kharab Kar dea ha

This bore is not good very danger

Very nice