steve williams
steve williams
  • 5
  • 685
How to Remove the Shutter Assembly on a Kodak Flash-Six 20.
I sacrifice this Kodak Flash Six-20 to see if the shutter assembly can be removed for service.
zhlédnutí: 28

Video

How to Dismantle & Clean the View Finder on your Kodak Brownie Flash Six 20.How to Dismantle & Clean the View Finder on your Kodak Brownie Flash Six 20.
How to Dismantle & Clean the View Finder on your Kodak Brownie Flash Six 20.
zhlédnutí 65Před 3 měsíci
Here is how you dismantle and clean the viewfinder of your Kodak Brownie Flash Six 20.
Squeaky, Sticky Shutter on Kodak Brownie Flash Six 20-How to Fix.Squeaky, Sticky Shutter on Kodak Brownie Flash Six 20-How to Fix.
Squeaky, Sticky Shutter on Kodak Brownie Flash Six 20-How to Fix.
zhlédnutí 58Před 3 měsíci
My 1940's Kodak Brownie Flash Six 20 had a squeaky and sticky shutter when I got it. Here is how to resolve that.
Replacing the Bellows on a Vintage Kodak No. 2 Folding Camera- Non-Glue Method.Replacing the Bellows on a Vintage Kodak No. 2 Folding Camera- Non-Glue Method.
Replacing the Bellows on a Vintage Kodak No. 2 Folding Camera- Non-Glue Method.
zhlédnutí 308Před 8 měsíci
How to replace the bellows on a vintage folding camera. The example here is a Kodak No.2, but the process would apply to other cameras as well. This particular camera has stronger metal tabs that hold the bellows in place, so I did not have to glue this one.
How to Replace a Bellows on a Vintage Folding Camera-Glue in Method-Kodak 1A or similar camera.How to Replace a Bellows on a Vintage Folding Camera-Glue in Method-Kodak 1A or similar camera.
How to Replace a Bellows on a Vintage Folding Camera-Glue in Method-Kodak 1A or similar camera.
zhlédnutí 233Před 8 měsíci
This is a step by step bellows replacement tutorial using the glue-in method when the metal tabs holding the original bellows in place are too weak to reuse. The example here is a Kodak 1A Autographic, but the method here could apply to other cameras.

Komentáře

  • @noahb350
    @noahb350 Před 19 dny

    Exactly what I needed, thanks! I will add, be VERY careful prying that sheet metal piece out of the back, it bends quite easily

    • @stevewilliams7577
      @stevewilliams7577 Před 19 dny

      @@noahb350 thanks for watching and your comment. Yes, bend the metal piece back flat before you put back in.

  • @charlesvail2443
    @charlesvail2443 Před měsícem

    Thanks for the tip on using the Shoe Goo glue...I have to replace a Mamiya 6 bellows and wasn't sure what to use. If it can hold a shoe sole on and remain flexible it should be perfect! 😎

    • @stevewilliams7577
      @stevewilliams7577 Před měsícem

      @@charlesvail2443 exactly. That's why I chose it. Shoes need to go in cold weather. Hope it works for you.

  • @plibit8506
    @plibit8506 Před 3 měsíci

    This is a life saver thanks for making this video 🙏

  • @Maijorsam
    @Maijorsam Před 5 měsíci

    Hello! May I ask if you know if the 27727 replacement bellows would fit on a Kodak 2C autographic junior too?