- 104
- 549 761
39knights
Registrace 22. 01. 2008
Video
Hooking up a Western SnowPlow power unit
zhlédnutí 24Před rokem
How to hookup a Western SnowPlow power unit to use on any kind of power angle 2-ram snowplow or anything really. Shows some of the basics of operation. I didn't have the hand-controller nor any literature on this blade and few YT videos to go by. So I'm sharing what I have learned and found so far.
Coleman CT200x Mudguard
zhlédnutí 65Před 2 lety
Just putting a basic splash-guard on the rear fender. Found the factory one still allowed water/mud to splash on my back while driving in wet conditions.
Bobber Spring Seat 2 Coleman CT200
zhlédnutí 942Před 2 lety
Adding a Bobber Seat Spring to my other Coleman CT200EX bike to make the ride slightly more 'cushy'. Actually makes the ride a lot smoother. Took some scrap 1/8 inch plate steel. Used a piece of cardboard to make a template. Welded a 3 inch steel hinge to the front. The rest shows in the video. Did not modify the factory seat in anyway (ie. did not cut off the factory plastic tabs, etc). Can go...
Coleman CT200x Bobber Seat Spring addition
zhlédnutí 1,1KPřed 2 lety
How I installed a set of Bobber Springs on my Coleman 200 to help cushion the ride.
Emily's Funeral Mass April 17, 2021
zhlédnutí 93Před 3 lety
The Funeral Mass celebrated for Emily Noelle Murphy. Also known by her friends and partner as Charlie Fay. Emily passed away at the age of 23 on April 12th, 2021. May she rest in peace.
Fatcat 1st Mock Up
zhlédnutí 38Před 4 lety
Just a quick mockup using an 8HP snowblower engine and an ATV tire I have laying around.
Fatcat Part 1
zhlédnutí 24Před 4 lety
This shows some of the disassembly process. Again with the 'scare-demic' on the go it will be harder and slower to source parts so this will be a slow build. Then again that will match the pace I do things anyway.
Fatcat Intro
zhlédnutí 17Před 4 lety
This is my attempt to build an old-fashioned Fat-Cat or Fat-Tire motorized bike. I was recently inspired by some of the other builds I had seen here on youtube plus I had been meaning to do one for awhile. Be patient as I may nt be that quick in getting this done.
2016 Civic shock replacement.
zhlédnutí 4,3KPřed 4 lety
Not a video on how to replace them but to show where and what size bolts are on this thing as it has changed from the earlier models. Guess Honda felt the need to repeat the same mistake Mazda owners have been dealing with for years. This move is an absolute idiotic one for Honda who should know better.
What oil goes in the stator housing ?
Your engine oil circulates through that area. It is not a seperate oil. Just put it back together and top up your engine oil.
Thank you buddy, thank you thank you thank you
has anbody tried this on a 1987 model?
Idk the next time you'll see a comment but dude I appreciate you heavily 🙏
Hey Brother! Glad to see you defending the one, holy, Catholic and apostolic church on ApprovedofGod’s channel. I made two videos defending Our Blessed Mother and that caused this. Would love for you to take a look. God bless you!
I’m watching to learn, just bought mine. I don’t think it’s wise to put anything that’s not hydraulic fluid or the dipstick in the system. I figured out an easy way to see new fluid on the stick. Just pull it out, put a paper towel, in contact, then read the wet spot.
Probably the best information I've come across on this subject. Thanks
Glad it helped.
I'm not getting no fire on my pick up coil
I'm not getting no fire on my pick up coil
I'd be making an extension on that thing !
Have you checked out the steel bumper reinforcement behind the rear bumper cover? I just did so on out 2007 that looks just like yours and 80% of the steel is gone. The bolts are so rusted I have not been able to get the steel off yet.
It probably would have been a Lil easier if you would have removed the back hoe
That is true; but think about it. You have to remove the backhoe attatchment to check a fluid level and then put it back on. It just would have made a hell of a lot more sense just to redesign the dip-stick to be a bit more practical/accessable. Fluid levels is something they suggest checking each time you start up the machine for the day. You might only take the attachment off once a season. To me it is just idiotic, thoughtless design. Besides there was another video before this one which explains why I had to check the fluid. Because of another design flaw on this machine, a hydraulic hose had chafed through and sprung a leak, so I couldn't work the hydraulics to remove the hoe anyway.
Nuts ! I have the same issue . Been wrestling with it for far too long . I don’t have the clearance to get at the bearing that you have . I’ll try the dremel I glad I found your post ,thanks
Thank you for making this video although you said you are not! Now I have an idea on how I would Mount one if I decide to do it.
To much bull shit where is the sight guae
Don’t order any filters from Amazon they don’t send the correct filters and then want refund your money
@39knights how did you mill the gears? Did you use a router jig?
amazing work btw
@@minicooper1944 There is a website which allowed me to print the gear template on an 8.5X11 sheet of paper. I then glued the paper to the pieces of wood. I have a small bandsaw with which I cut out most of the gear, finishing it up with a wood-file. You could probably use a jigsaw or even cut them by hand with a coping saw I suppose.
@@39knights Do you happen to remember the site? That would be fantastic.
@@minicooper1944 You can check out my next video in this series called "How I Made the Bissett Gears" or czcams.com/video/UEzBMpBoqmM/video.html shold answer your question.
engine should have been turned anticlockwise not clockwise
why ? does it damage something ? Ty
Thanks me son. I gotta do same job.
SAME THANKS
Great stuff. Cheers
Did you have a second c ring that was smaller working kinda like a thruster towards the back of the cam? I lost mine and I can’t find it online anywhere. Was wondering if it was crucial.
Just got my bearing off after 4 hrs of working on it. Saw this video 5 hrs later, just my luck
Dude ! Thank you for posting this video! 6 years later and I'm beyond thankful!
Thanks. Glad it helped.
Great job bud, i hit the sub button, another channel to the list. Cheers my friend
Snapped my rear left axle on My 1999 king quad 300 what should I do it snapped at the u joint so I could get a new u joint and weld it together let me know should I just get a new one
Thanks
You are correct sir. Just siezed.
i love it well done music was interesting too
If I had to listen to those geese for more than 5 minutes they would be in the oven
What a GREAT instruction, so very clear precise and understandable for us dummies 101. Thanks ! Great Job
Oh what the model of this type of e-bike is this called
I got an e-bike like this I am looking for parts. The throttle handle one with the red and green button on it do have a number or name of the part for this
Did you order a engine rebuild kit that comes with instructions. If so where? I have a 99 arctic cat 300 that needs rebuild it got suzuki stamp on the motor but can't find part though arctic cat or suzuki that says it fits
Its knocking
It looks like our 1999 we bought new. It is a tank in low range. No problems with this bike in 23 years of owning it. Knock on wood.
im about to replace my front diff. thanks :)
I had no problem finding battery in FRANKFORD as it had a piece of paper sticking out to let you know for us dumbies lol
Also had 2 batteries...
Brilliant video. Learned more in 5 minutes than I have browsing for hours
Hi I was wondering how u made the scoreboard. If u could send me a video on how to make one I greatly appreciate it thanks.
Holy crap man u helped me out twice today thank you very much!
I have to do the same thing right now. Thanks for giving me some insight
I did find over time the waste oil would cause the pvc pipe to become brittle and destroy the threads. I have since replaced the pipe with a threaded galvanized gas pipe pieces from Home Depot. Not expensive, and much sturdier.
I was going to ask how the plastic pipe held up to hot oil. Can you post a video of your new setup? Or a list of parts like you did for the plastic parts?
Great idea!!!! One thing I thought maybe use a heat gun to taper the top black tub. Just a thought but great idea and definitely cheaper.
Buddy Tanks luh..
Needed this video ty very much sir
nice work
It's pronounced Ki like the wild dog 🐕, Not Key like a house key! Why don't you pronounce it correctly and stop sounding like a idiot!!!
Thanks for explaining how the camshaft needs to be situated when setting the time. This is the first video I saw that actually explained it.
Is the guy in the video name Vince T 🤔