Video

Super helpful❤

Mine did way worse in 1 hour of riding but i guess there was too much oil also

Great video. We were actually on the trail and found that my friends 112 was running like crap . I looked videos on the trail for him and came across this. You saved the day, after the video I had it running 90 percent better. In our case the air screw was way too far in . Only 1/2 turn out. You’re my hero . Thank you 🙏. Im also curious to see what number idle speed you feel is appropriate. Based on what I heard in the video, I’m thinking around.1400-1500 rpm? This is just based off of my bike that has a tachometer but a fuel injected 2T

If you turn the drill on opposite direction that the dremel will be easier 🔵🔵🔵🙂🙂🙂👍👍👍🔵🔵🔵

Thanks for this video got the daughters 2003 kx85 running sweat now. Air screw was screwed all the way in. How do i know of its to lean.

thank you, this is the answer I've been looking for, how does the rc nitro engine start after the igniter is removed

What ever happened to the bandit build bro?

Nice fix dude

Thank you for making a disassemble video. but when you were removing your carburetor the nut you loosen after you’re done loosening it push it in as far as it’ll go and then the carburetor will slide out easy I don’t know if you know this already it’s been a while since you posted this video Ty

crank seals maybe

I do this all the time when I’m borred

Yes that’s perfect

don't use pliers, use the correct spanna or a small shiftin spanna....so ya dont damage it

Sorry to hear of your loss. The channel lives on, it must be difficult. I'll shut up now. Hope you are all ok.

It is HARD to sleedrun a Bandit. Try to get it over 100 mph first! Love the desire… can’t wait to see how far you can take it.

Hi there. Hopefully this message gets seen. So a strange thing happend. I turned on my kraton for first time in maybe 6 months. So Dx5c on, car on… now usually you have the common 5/6 beeps the car does before its ready to go. But now it does like 2 beeps then the fan slows down and its just idle. But check this… if i turn my steering full right lock it ramps up the fan again, the beeping resumes as normal and then its ready to go. It will actually drive (but only in full lock to the right😰) when i let go of the steering wheel the the fans slow down again and the car is idle. Any idea how to fix this bizarre problem?

So I'm thinking about getting a c54-1 off of Amazon is there aftermarket support for these? I see these all tricked out is it hard to do? I'm currently doing stuff to a volcano epx making it fast, after this I want to tackle on one of these to crawl with friends. They have the traxxas c10s and was wondering if this would match those.

Great 👍

Thanks

Great video

Best solution is to axle mount the steering servo.

Super cool video, thanks for sharing.

Make more videos 🎉🎉❤

Thank you for explaining!

ALl i had to do is Loosen the Servo Steering rod behind wheel, 2 turns. Gave it more room to move. BOOM. Thank for the video.

LoL! I didn't think of that!!!!! 🖐 But I'm waiting till some softer replacements arrive before I mess about with my Tamiya Land Rover tires. Hehe, they aren't new, just hard from several years of shelf life in a model shop. But I'll deffo try this first!

Cool video, nice free mod basically for all wpl rtr rigs. Almost all of them have those same axles and same links

👍🏻

In all honesty I get a completely different body (I have a ‘73 Ford Bronco body by Proline w/magnet body mounts) then move the battery down low (I have the bowmans lcg battery tray) also a shorter battery (I have the Gen Ace 4300 mah shorty @50c rating) also can move that same up front just past the servo there’s a spot to run a strap which works great! And then a slew of options of anti foams or dual stage foams for your inserts which dramatically can handle weight transfer to the rear and side hills great! Then of course brass down low up front.

can you monitor the humppack-voltage on the display of your transmitter with this receiver?

You just saved me 300

They make heat sinks and fan compos for the motor on the traxxas site.

I'm thinking of doing this soon. THanks for the advice

What is the new carb?

Is there any link to that print? Thx in advance

HOW DO I REPLASE CLIUCH ON MY XTM MAMMOTH ST SWAP

I got my idle right but when I hit the gas, it goes up but then takes a few second to come down. Any thoughts?

What size did you use for the exhaust valve?

Is this the one after the catalytic converter?

Hi bro, you know the size of your main jet , pilot …. ?

The front diff on my yeti blew up not long ago and ive spent 5 hours trying to replace it and a broken servo motor😭 somehow one of the screws got stripped and it is stuck in there, rip front differential body assembly💀

FYI For the 2 speed transmission there is a small ball bearing then the small spring followed by the grub screw !!!

should probably adjust that chain tension but good video thank you

For such a young CZcamsr, you really know how to film! Helps me a lot, I'm going to buy a sunset bronco and wanted to make sure i didn't need to set endpoints when (eventually) the servos break. Going in my rc help playlist!

would it fit a 50cc baja?

If the rear shocks are compressed does it hit on the tray or does it max out like normal

Mine started making some type of hissing noise and the steering is stuck... What do you think it is?

Turning out means more fuel Turning in means more air