Video

I appreciate you sticking around Yohan! Yeah this CZcams is a real struggle with no reward except getting comments from my subscribers like you, so it means a lot to hear from you bro!

You know I am buddy! Hope to see you there.

Thanks for watching and for the wonderful feedback!

Thanks for you comment Diego! I appreciate you family!

Thanks for commenting and watching the video Mike! It ended up being a water pump. It only over heated when the weather was near 100° and I was wheeling on the trail. It did it again on Slick Rock and I had to change it on the side of the trail. That video will drop next week. Thanks again!

Awesome. Glad you got it sorted out

Hahaha 😂 yeah you’ll be fine and riding in comfort. Thanks for the comment!

Thanks for watching and commenting on the video! No, the linkage did not pop out when I discover the gear was clocked wrong. I really don’t think that would cause it. If you watch the portion of the video where I hooked the linkage up you will see there is a plastic clip that the linkage rod goes into. Make sure that it’s clocked right because the rod snaps into it at only one angle because of a slot in it the rod fits into. If it’s not snapping in you may need a new clip but I don’t think Audi sells it separately from the whole seat assembly. I hope this helps, good luck and let me know if it works for you.

I can’t remember the size of the torx unfortunately. I think around a T4 possibly. Thanks for watching the video, don’t forget to subscribe!

Thank so much for watching and commenting. I appreciate the channel support! Don’t forget to subscribe! 👍🏾

Yes, it can be done without taking the seat out of the vehicle. Thanks for watching and subscribing, your support is appreciated!

I was in off-road mode and the tires are Toyo Proxes ST. To be honest after 2 years the Toyo’s are getting a little noisy on the road so I will probably replace them with my favorite all weather tire the Continental DWS. Thanks for watching and subscribing, the support helps the channel!

I glad you enjoyed the video and I hope it helps! Thanks for watching and don’t forget to subscribe!

That’s what’s up! To the stars ✨

Thanks for the comment. I appreciate you!

Hahaha, awesome. I may drop a video on it. I hope you subscribed 😉 Thanks for checking out the channel.

Next time bro. I will try to remember to DM you so we can link up.

Thanks @chevysrus I appreciate you my brotha!

Thanks for the comment Johan, I appreciate you still supporting the channel. I have been very busy lately and it’s been a struggle to keep up but I’m slowly working through it. I may have to do some family vlogging to fill the gaps.

Nah they not tripping off that. In most cases you can even order online you just have to provide the pre smog year of your Vehicle. I’ve never had trouble with Summit. I do however go once a year in person to get some of the big items. I hope this helps, and thanks for watching. Don’t forget to subscribe!

Just subscribed! But appreciate you getting back. I got to place a special order and go out to Nevada to pick up. I just don’t want to drive out there and be denied. Thanks for the help!

Thanks for the support Rob! I appreciate you my brotha!

It’s my girls car. Probably won’t do much to it.

Thanks for your feedback, I appreciate you watching!

Thanks for the comment @billhagerman4475 I will try to see if Summit have the front cross drilled and slotted rotors for the front. Good idea.

Thanks Johan, I’m trying fam! It’s nice having the support from across the world! We take this intentional my guy, yheeee 🤘🏾

Thanks for the comment @dogdollaz1971 I appreciate your support!

Thanks for your long time support! One of my day ones, I appreciate you!

Thanks for the comment @1bluensx I appreciate you!

Thanks for your comment Jacobo! I appreciate you supporting the channel. Its subscribers like you that make it worth it.

Thanks for sticking around Johan! I had a lot of personal things to deal with the last couple of months, but I’m back. Hopefully one day I can have enough subscribers to make videos full time. I appreciate your loyalty fam and I’ll keep working hard on building the channel.

@@BrettMedia OH i figure something had happens. I hope its turning for you to happy times. We understand that life comes first. Its looking good your skylark:) great job!

Thanks Ephie! I always appreciate your support! 🫶

I’m glad to be back, I couldn’t do it without your support! ❤️🤘🏾

Thanks my guy, it’s good to be back. I had a lot of family stuff to take care of so had to step away for a bit. Thanks for sticking around Fam!

Thanks @Q8FAB I appreciate the support and encouragement!

Nope, no engine light and no noises after I cleared the code. I required no programming of the motor either. But note the parts were original Audi parts (air shutter and motor together as one unit). I only did what you see in the video replaced it and clear the code. It’s been almost 2 years and no issue. Thanks for watching and don’t forget to subscribe!

Do it! The Quattro system works great. Hopefully you don’t have low profile tires and big rims like I do. Keep in mind I did have light rocker panel damage, although I didn’t get video of that angle. Thank for watching and don’t forget to subscribe!

@@BrettMedia ok bet. and naw i was thinking about putting some rims on it but not until after i put her on a nice trail.

Thanks for watching and for your support! Yes, the pulley change and a tune will definitely make it whine more. I had the ARP pulley and a stage 2 tune on my old 2013 Q7 and it was amazing. I haven’t done the pulley on this one yet.

Thanks for the comment, I appreciate your feedback! 🤘🏾

Awesome tip @Z33Garage ! Thanks for your input, I appreciate the view and support! I will have to tap into your channel and check out your content.

Sup Cuzo! Been a long time Fam. Imma DM you. Thanks for tapping in, don’t forget to tap into my IG too. @brett_media_ig

Cuzo, hit me up on my IG I want to DM you for contacts: brett_media_ig

Sorry, #mybad. I’m not sure if they’re the same but if so it’s not that hard to do especially if you’re just replacing the glass. Thanks for watching!

Thanks for the comment, I’m glad you enjoyed the video. I appreciate your support!

Glad to help my guy! Thanks for your comment and support!

Man Sammie, it’s been a minute since I’ve worked on the Buick. I’ve had a lot going on around the house the past 3 weeks. I hope to get back on it this weekend. Thank you for the support and the push to get back to it again. Stay in touch fam!

Thanks for your comment, I had a “P05 A0” code. I hope this helps you!

Thank I have a same problem whit the p25AC00 I thing so is the oil cooler housing and oil cooler valve

The parts were about $350. 1 week lead time on special order.

It felt pretty standard as compared to the stock clutch. I never made it past the break in before I sold the car to fund the next project so I never got a chance to smash on the gas. It held great on a few slide though. I honestly almost regret selling it. However I can’t keep every project. Thanks for your comment fam!

Yes, The Audi does pretty good. I love the Quattro system. Also does well on slippery boat ramps and mountain snow conditions.

Thanks bro!

No, I didn’t touch the pinion gear so no preload adjustments or checks. I reuse existing ring gear and pinion so as long as the backlash, runout and tooth patten are in spec you should be good. You will also need to set your carrier bearing preload. I hope this helps. This full video is on my channel for more reference.

Thanks for the comment @heavychevymoegritty I can’t wait until spring so the snow melts off the trails!