Video

I don't think U13 is a retimer - source signals seem to be AC biased (caps) while output is TMDS (hdmi) so I'm thinking its maybe a displayport to HDMI bridge. unless this is some quirk of zynq hdmi output that it requires AC biasing but even then I'm not sure how that would work.

This can also work as a room heater lol

Ok, a couple dumb questions: What is the exact threading INTO the tank? Standard 3/4" NPT pipe threading? Put the tank outside, exit down, in the sun on sunny days, for drying. It'll dry. I'd like to make a quite small tank for high portability (and just a little air for cleaning / dust removal on small items) out of a 1 lb. propane bottle. Is the threading the same?

from like 1:36 on, can anyone explain the stylus jumping lanes?

I began my career in refrigeration in the UK 1976 and only came across 3 or 4 "pancake" compressors which were made by a company in Scotland I think called Sterne. In those days Frigidare and Prectcold compressors were the main ones used in refrigeration and in the Frigidaire range were belt driven and the semi-hermetic which were called Dynapac. I worked for a Frigidaire dealer rebuilding compressors. Great video thank you.

We're now at the same point with leds that we were with cfls, where the cost and build quality has plummeted but at the same time the quality of the light has improved along with efficiency.

Good old days….

You're just a parts changer.

THANK YOU!!! After watching your video, I was able to diagnose and repair my Genteq ECM 2.3 1 HP motor. Mine had the same symptoms as your motor. When I tested the ohms across the 3 leads my readings were 1.2, 4.8, 4.4. I read they need to be the same. I disassembled the motor and fortunately located the wire that was causing the problem. I bent it and applied epoxy resin. Checking the ohms, I now have 5.6, 5.6, 5.6 and no shorts to ground. The bearings seemed good and also the ECM modules didn't appear to have any burned area. I reassembled and installed the motor and IT'S WORKING!!!! Don't know for how long but at least I was able to get the A/C back. I found your video courtesy of grayfurnaceman. He mentions your video in the comments section.

It’s a bird, it’s a plane, it’s…somebody vacuuming!?

This was the first video of theirs I watched, years ago. Arcing that motherboard still sounds like music to my ears- you could say it's a major turn on! 😆💥 Editing/rendering with that power supply? 🤣😉 Still love the random jar-blast at the end! 🙃

Thank you ❤

Mind blown goodstyle!😵‍💫

Is it for FPGA ZYNQ or generally for FPGAs ? What are the differences ?

Daikin invented the swing rotary compressor，it won‘t have this issue

Did this a work a few times .. it's impressive how much light an HP high efficiency red LED could emit, and how long it could do so .. i think we got it up around 4 Amps, as long as it was submerged

Would be cool to do structure from motion with this

I have a panasonic NNT945SF. the lamp is out and ive searched a hundred videos and i cannotttttttttttttttt find where the lamp is to change bulbs. it use to light up and it stopped. it still heats fine. but when i open it up theres no lamp where there are in 1 million videos ive watched. its like the microwave was lit up with the spirit of christ. ive taken the cover off and nothing. its like they never put it there.... but its there. lol

Wow! Don’t know if anyone else has asked this, but is it a myth that shouldn’t play an LP more than once a day due to heat distortion? Asking for a friend🤔

Did you managed to repair this?:) I have a V7 now which has similar issues:)

Бубух

Love the anti-backlash design. Does your first version's yaw work well? (Ie. when all the vanes turn CW or CCW). I had the idea to make something similar in an RC airframe so it would be actually a roll movement and wondering if it would be enough to overcome the wing's resistant. I'm trying to stay away from needing any control surfaces like ailerons for rolling.

3:58 that’s the propeller blade of the lawn mower.

What if you add 4 wings on side walls?

The Philips lamp with the 9F date code was made in 1999.

Any information on the piston seal or ring?

Please upload monochrome photos and videos . 😊

Do your 2 ESCs connect to the flight computer / your 5v circuit via BEC, and do you have the positive terminal of one of the BECs capped or are both fully plugged in? (I'm learning how the electronics on these work)

I need this electric turbo

I watched this vid back in 2017 when I got into film as a hobby. back then I had no idea what I was watching. Here we are in 2024 and i would love one of these power supplies. I use a much older one. Your vids are incredibly helpful

i know this is old, but... could this concept be used to act as a power shop vacuum?

Quick question, where did you buy those spring steel landing legs for this project? I have been looking for something similar for a personal project.

Trabalhei 12 anos com esse projetor.. muito bom. Silencioso .

Fan doesn't have enough thrust, don't buy his stuff.

Nice cgi

phased lag !!

damn, idk why you offered the files and the programming for free, but thank you very much!

It’s a cool toy. Get rid of the LCD screen. No one who actually films in the field uses the screen at camera level. It will save battery.

Hi I really enjoyed to see how wonderful project is air liquefier. But why there was only a few video?

Thank you for this awesome video…Can this cut metal? I’m a bit confused about the low power, (500mw), how is that amplified to cut metal? I’m looking into a diy laser cutter but I’m not sure which power I should get and how that power is increased. If someone could explain I’d be grateful. Thanks

Thank you for this awesome video…Can this cut metal? I’m a bit confused about the low power, (500mw), how is that amplified to cut metal? I’m looking into a diy laser cutter but I’m not sure which power I should get and how that power is increased. If someone could explain I’d be grateful. Thanks

Never understand why they discontinued the superior airblades from the 2000s.

Great Content!

Looks like the futur of high speed drones 😊 and i think you did find a new form of video for relaxing, those slowmo shots at the end where the wood starts flying around everywhere are sooo relaxing to watch 😅 specialy with that music 👍

How the Hell Did the Train Trailer was being looping all the time 😂😂😂

11:41 I saw a frames of the Dolby Digital Train Trailer

Hey since theres no contra rotating blades / turbine fans how are you cancelling out the rotational torque that gets generated by the rotation of the blades? Do the control surfaces at the bottom able to rotate independently and generate yaw authority?

sooo the valve though. details?

Hello my friend Can I know the code on the IGBT, please.

I have no idea how much torque you were able to pull on a crescent wrench but I doubt it was more than 100 Ft. lbs. I'm just making an observation as I used to pull 600 foot lbs. on the inboard flap track fail safe straps on the 747. It was lots of fun!! Anyway... I'm looking at using a couple old propane tanks to hold a vacuum for the forming table I have planned. Got to make some DEVO Energy Domes!!