Video

Awesome print 5.1 could use some polish though it's kinda buggy on windows 11 but it's well optimized for the machine

how do i get it at the starting level to begin with the paper, when i click home leaves big gap

Can the NEJE 4 Max laser with the E80 laser module cut and engrave plywood directly without using a honeycomb bed? I want to move the laser over a full sheet of plywood to cut out larger parts using the ‘pass-through’ technique.

The question is how will the k1 cut the filament and where will it discharge?

It's Alive! Again. Thanks for the walk-through tutorial! It was quick and easy.

ok working but when i want flash it i get in stage1 20% ERRRRRRRRROOOOOOOOORS idk whyyyyy its so shit machine

i did all this but it didnt show me this "boot device" in device manager

need i disconnect all cables from board ? or can i keep connected and only connect microUSB to computer and make recovery?

YESSSSSSSSS !!!!!!!!!

nice, but I installed slicer V5.0 and didn't work, all bottons are out off places and the screem plate are out off center, you can't see the bottom botons.

Hello, I have a K1C, can I make it multicolored?

I would love to buy this machine with the main aim of cutting on that thin stainless stell sheet but am not getting any oriper review on that. What am seeing all over are the reviews on wood,boards,acrylics etc with very minimal to no review about its capabilities and performance on the steel cutting. How fast and at what power and speed. How smooth the cut is. The challenges etc

Best tutorial for bed leveling I've seen. Thank you.

thank you... help me a lot!

I did this method, and oh my God, my levelling is beautiful sat at .154 that's so much better than my last k1 I had to send back to creality due to the bed being wonky and getting failed prints finally I don't have to worry about that and I can do my linear rail mod and fix the issues it's got due to the vibration compensation I'm getting bad ringing and banding within my prints so I'm gonna do the linear rail modifications to see if this fixes the bad about my k1 speedy as iv rooted the k1 aswell so I have full control over the marcos finally 😅

Cost?

I thought auto bed leveling would compensate I'm a noob at this.

I have a V2 with a 2.4 mainboard from 2018-8-13 but klipper is never able to communicate with the board. I have re flashed it 4 times and recompiled always the klipper firmware but no success. Looks like you have the silent mainboard but my was the modell before. Does anyone has install it successfull with the old version?

Thank you for your information! Could you also give only the support a color? Thanks!

Thanks for the interesting video. Currently (May 2024) the Neje Max 4 is delivered with drag chains. The price is approximately $500. The honeycomb now also fits between the front and rear rails. An aluminum plate is also included for use as a base. My problem with the laser is that the frame is not at a right angle. As a result, the Y-axis hits the frame first and the limit switch often does not reach the frame. Furthermore, the laser module is not vertical. The laser module does not run smoothly on the linear rails.

Hey, could you please add the ability in your script for the process to restart once it gets stuck mid process on the c++ version of Pi-PppWn? Thanks.

I was unable to use Windows 11 for this, it wouldn't find the "clone device". Moved over to a Windows 10 computer, bing, bang, boom, finished. Thanks for the tutorial!

does anyone know if the CFS will be compatible iwth the Ender 3 V3 Plus?

everyone says on K1 and K1Max but what about K1C?

Nice video. Which motherboard is in your printer?

Where did creality announced this CFS upgrade? Not able to find any info.

Great video but I have been unable to get it to happen either using my desktop PC or laptop - both running windows 10 - the laptop won't install the driver but runs the clone software, and the desktop installs the driver but wont run the clone software :(

Hopefully they release the CFS system soon, love to get one.

This printer has about the same quality as this video. They are both a cheap export of a second rate distributor.

Can I ask will it have a new tool head in the kit ?

Thank you for the content. What are your thoughts on upgrading current K1 printers with the Bondtech kit and jow that will work with the new filament system?

Using windows 11 I just clicked and installed the driver software opened up the base of the k1 max plugged in the micro USB and USB to my PC turned on the k1 max power the board lights up 1 blue light solid and 1 flashing my PC made the USB connect sound started the software and followed the rest of the video all worked and I'm back to where I was when I first started the k1 max gone through all the setup and now printing Thanks for all the help and I hope this might help someone 👍👍

7 months down the track, if you had to choose one, which one would you choose?

In this video you adjust the front lead screws manually. How to I adjust the rear lead screw? My mesh is high at the back

Great video! Question for you, where did you find that cabinet?

Awesome. Worked for me! Better than the actual creality support

but why auto bed leveling not compensate that?

Thanks for this very interesting video! I've upgrade my CR10s Pro and bought the same screen, but what ever is the power supply I put (wnet up to 3A), my Pi 3+ keeps crying that it hasn't enough power... As if the screen was draining too much current. However, there is no way to power the screen seperetly... I was wondering if you had the same issue?

light not blind but I'm not showing in device manager ? Windows 11

I can't get it past "start burner" what can I do to get it to start?

Mine came with a cable chain

Do you have some source for inexpensive textured K1 PEI plates?

Great review but I still can't decide between the two. Currently using Anycubic Kobra 2 Neo and want to upgrade to a faster, high quality printer. The K1 Max is on sale for $1211 on Creality's eBay store and the X1C is $1839 (without AMS) so there's a big price difference there. I've heard Bambu lacks customer service and Creality requires more tinkering to get quality prints out of the box. If K1 Max had AMS I'd buy one without hesitation.

Thanks for sharing, I also like the possibility to use a screen that is part of the printer itself.

Where can i buy this build plate can you paste link?

at 6:28 you show the bed leveling data but that looks very different to my creality print interface - or are you using something different? I don't have the numbers or the mesh size - just the graphic.

Fantastic test. Very valuable information. Thank you so much.

Thanks mate

Thanks. Check out a first layer though. I carried out the same procedure as you, thought the mesh looked much better, but the first layer over extruded intermittently with under extrusion. So out of frustration I removed the silicon spacers under the bed and installed m4 screws in the corners with springs (think bed slingers) and adjust the bed now manually while printing a first layer. Old school, but it worked a treat. Personally I think the K1 leveling issue at least requires a firmware update. But it’s a reasonable machine for the price.

Good morning. Thank you so very much for this vid post! You likely just saved the day. Cheers and thanks again. Ron.