Video

Hey would you still use it or just getting rid of it ?

What is the diameter of the coaxial cable and copper cable, brother?

What is the diameter of the coaxial cable and copper cable?

Glad I found you.I just bout some I didn't know what side was positive was until your post.

Or are they listening...

Manure spreader. Lol

homie thats a air sensor :sob:

hi bro can i know what is the name of this camera with the model number or can i get your contact details like Instagram id or any thing

I keep having to do that because it won't stay bound.And I have no idea why and I can't find any information about why it won't stay bound

Because they're all 2207 motors regardless of kv.

so how would i connect it to my laptop?

I visited there 12 or 13 years ago to take photos of me in my daisy dukes and top and there was guys in the tunnels doing non-exploring and I got asked from a few if I'd like to join them for fun,,was alittle bit creepy but I still got to see a tiny bit of the area while there..I loved visiting the fort..

Maybe stay away from wacky weed before filming?

Bro did you just epoxy that arm to your vice?

Amigo como activar mensajes RTCM ?

Ah dude this is awesome! Thank you!

I'll get the mutha open... Bet! 😜

I don't have a freakin vice! What else will do it?

I fly here when I’m in town visiting my parents. I found a prop there and was wondering who else flew fpv

That's actually pretty clever

If you connect a device to a 5v 2a power supply, you are looking at a constant voltage power supply. The current is variable. The device should theoretically pull current until it doesn't need any more. Unless it is rated for a lower voltage, or for some reason needs a constant voltage and constant current (like a laser diode), then any 5v source with enough amps to power the device should work fine.

Hey, is there a way to zero out the the altimeter? When i turn my quad on it says im 230ft in elevation which i think is close to where im at above sea level. Is there a way to reset that?

dood, this is a fabulous idea!

when you describe a battery as a “thing”

Thank you for this tip.

So I usually reuse the old magnetic rotor since the older ones had a brass bushing, I just replace the little soft plastic pinion. Some of the 60s and early 70s models of these motors have a brass drive pinion, which is very nice. Only problem with those is they run a bit loud, thats why they started using the soft plastic ones instead. There is a lot of these WG series motors out there, they all use pretty much the same parts. I've never seen the larger gear fail before. It's a great design motor, that's why it's been in production since I believe 1967.

That's an awesome display, where you can see the light mask moving as the minutes change.

Good luck finding a source for those tubes. I haven't found one yet, either... I've got the same model with dim tubes.

If there is only one port and it still not blinking, what do i need to do?

yeah didnt even try to hide the grinder :D

thank you helped me out 👍👍

Hi My Webcam has 4 wire Red no 1, white no 2, green no 3, black no 4 Which cable do I need to connect to the VTX

where did you get that

The reason they are all interchangeable is because the windings on the stator are what effect the kv rating. The bell is the same on all kv versions for *basically every brushless motor*

Super neat!!

Thanks for the video. Do you think a TN111K would work?

Just tried this on a Panasonic RC-6304 with a TN311K timer from home depot, it worked but I had to sand a little bit off the bottom of the stator because it was raised too high and also wiggle out the rod that holds the old black gear in place and glue in the one from the timer, it keeps time but it jams up rarely and makes some racket when the switchover occurs sometimes but it works for now! It seems to get better as it breaks in but we’ll see

Dude there was literally no point to this video. What was the point?! We know they use samsung cells..... Its cause they still sell 1.5 amp batteries in a world with 9 amps. You said "um" 6 times and "uh" twice in a 50 second video. Please never upload anything to the internet again. Hefty fuse meaning more amps? Oh yeah they need a higher amp fuse for higher volts........ You kidding me? The higher the volts the lower the amps. No thats exactly wrong. Dont open things you know nothing about and attempt to "show" anyone anything ever again. I bet you think you're the smart guy in your family too... - The internet.

I’ve read tons of reviews that say the B&D 40v batteries are crap. Was that your experience and reason for posting this?

thank you sooo much dude, this worked perfectly!!!👍

Hell yes, Smart

Darlings, there are 3d-printed adapters for this available on Etsy. BUT what about vice versa? I am using the TSTAK trolley so I somehow need to connect deep pros on top of TSTAKS… no adapter yet? 🤷‍♀️

where did you get your heat shrink and what size are they?

Bruh, 10 mins to connect and no explanation...

Flux is good but most solder has it in it already.. The "trick" to soldering is tinning the wires first!

Appreciate this. Very handy for focusing the camera before installing or having to heat up the vtx. Your bench looks like mine after a project. Then I force myself to put everything back in place before going to the next one lol. You have a lot of cool and helpful stuff on your channel. Subscribed.

😂😂

I keep getting the message “connection break” does anyone know what that means? Cause it won’t do anything after that so I can’t charge my battery. Keeps me that message every time

this was a good video, i just repaired an arm and was curious to see how others do it

Then it needs to be purified