Video

I only shoot sub-12 air rifles in the UK, I am sure if you are shooting high power or real rifles all info would help, thanks for the comment

Yes, its a great scope, if doing close work I would go for the new one, I think it 4x12 or some thing like that. The bc takes a bit of time to get used too. Plenty of youtube and facebook groups to help now

ye gr grains , g grams

Hi twist rate isn't that important for air rifles so I just left mine as default

Lol, Take it you don't shoot at night, kinda like adding stuff to a quad to take it over 250 grams glad you enjoyed the video.

Hi you need to have the Bluetooth on in the scope and your phone, sure it turns blue when connected, u also need location services on on the phone, if its not working uninstall the app and reinstall and make sure you accept all the permissions during install cheers

Thanks appreciated its all the gun and scope

min range finder for ir is 10m it will focus down to below this

0.018 works for me cheers

In the UK we are sub 12 ftlbs , so it is around 11ftlbs Cheers

yes, usually this wont range anything under 10m getting there with it though

All down to the brk ghost

177, sub 12, carbine cheers

sub12, 715fps

Yes Sub 12, all down to the Ghost, Thanks

@@markdyson4904 what set up are using I have an MTC copperhead scope on mine and just using a pillow my sister knitted 😂 for stability. I can only manage groups of about 15-20mm with all 13 pellets at a target 🎯 30 metres away

It looks your shooting pellet on pellet at 40 metres which is excellent. I'm using the jsb exact 8.44gr in 177 and the field target trophy in 8.64gr

@@umarsaddiq7195 Scope was a pard008p 50m card, sub 12 jsb 8.44, hand n ftt and the heavier 9.57 ft work well using immersive optics 14x50 now. bipod and holding the rear of the gun laying prone

Fantastic rifle

Its a fantastic Gun

ye need better cameras

@@markdyson4904 yip but still good keep it up

should be rws 8.4 at 53 yards lol

That's what i thought a first, however, after feeling air escaping when firing i decided to check the reg 1 1-2 turns now no air and very quiet. spread 44 and deviation very high. now down to 9ish so defo an air leak at the reg

long time ago this. this might help but not sure.ri Ervaskivi Also another instruction found. Should also add here as file or sticky: On the transmitter the controls are used as follows: Gear switch: Camera recording On/Off AUX 2 knob: Camera tilt Mix switch: Flight modes 1-6 (depending on D/R switch position) D/R switch: Flight mode bank 1 or 2 select FMOD switch: Not used **********Thold switch: Throttle hold (50%)******* The receiver (marked RX 703) is hooked up as follows: Output 1, marked "data bus": DEVO M flicht controller Output 2, marked "AUX4": Camera tilt Output 3, marked AUX 5: Camera recording On/Off Parameter setup for the DEVO F7 Function Menu > Travel Adjust > Gear: +65%, -65% (all others are unchanged) Function Menu > Sub trim > Gear: -20% (all others are unchanged) Function Menu > Program Mix (I use mix number 1, but it is a free choice) TYPE: Normal ALL SERVOS HOLD: Ok MASTER: Gear SLAVE: GEAR POS 0 < >: 0 POS 0 <->: 0 POS 1 < >: 48 POS 1 <->: -100 OFFSET: -63 THROTTLE STICK: Inhibit Switch: Pos 0 (not important, only shows the position of the D/R switch) Model Menu > Device Select > Flight switch: Inhibit Model Menu > Device Select > Flight mode trim: Common Model Menu > Device Select > Thro Hold Switch: HOLD SW Model Menu > Device Output > Gear: -> MIX SW, Active Model Menu > Device Output > Flap: -> AUX2 KB, Active Model Menu > Device Output > AUX2: -> GEAR SW, Active That is all. With the parameter setting described above I obtain the following results when I look in the flight mode screen in the Mission planner program: With the D/R switch in position 0 the Mixing switch selects flight modes 1, 3 and 5 With the D/R switch in position 1 the Mixing switch select flight modes 2, 4 and 6 I use the following flight modes: MIX , D/R, Mode 0, 0, Stabilize 1, 0, Loiter 2, 0, Circle 0, 1, RTL 1, 1, Loiter 2, 1, Auto 5 January at 23:33 · Like

+So-y-v mille was just the standard pid settings with multiwi, changed to a flip32 board and on luxfloat standard settings.cheers Mark

ok merci

+Michael Law main thing you have to do is change the escs, and a pwm devo receiver to programme the escs, yes i have minimosd and full telemetry. but to be honest a 450 frame, apm26 or28 m8n gps motors escs give yo a goob machine, just had these parts as spares so thought i would give it a try.